Konrad Rzeszutek Wilk wrote:
> Ooooh. Can you give some more details on the hardware flavor? CPU? Memory?
Its an AMD system on an ASUS M2A-VM mainboard with an Athlon 64 X2 CPU
and 8GB of memory.
> What happens if you use dom0_mem=max:512MB or pass in 'irqpoll' to the
> Linux kernel?
irqpoll does not change anything but the memory limit does the trick.
The system then boots fine, I attached the dmesg log.
Since the netconsole now also works, I assume some kind of IRQ problem
which is strengthened by the fact, that the keyboard didn't work either
(for scrolling and searching for problems) without the memory limit option.
> OK. I need the kernel boot log to figure out what might be a potential
> problem.
> Let's try to get your netconsole working or your serial console? Does this
> machine even have a serial port? Maybe you can use that to capture the kernel
> output?
I attached the bootlog with the 512 memory-limit enabled and the xen dmesg.
Unfortunately I have to drive 200km to install a serial cable to the
system. So if there is an IRQ problem would the serial console really
help or would it suffer from the same irq problem?
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.31 (root@brontus) (gcc version 4.3.2 (Debian
4.3.2-1.1) ) #2 SMP Sat Sep 19 15:53:55 CEST 2009
[ 0.000000] Command line: root=/dev/mapper/brontus-xen_root ro debug
netconsole=4444@xxxxxxx/eth0,6666@xxxxxxx/00:12:1E:19:D0:BC loglevel=10
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] xen_release_chunk: looking at area pfn 20000-ddee0
[ 0.000000] xen_release_chunk: looking at area pfn ddf00-e0000
[ 0.000000] xen_release_chunk: looking at area pfn f0000-fec00
[ 0.000000] released 0 pages of unused memory
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] Xen: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] Xen: 000000000009f000 - 0000000000100000 (reserved)
[ 0.000000] Xen: 0000000000100000 - 0000000020000000 (usable)
[ 0.000000] Xen: 00000000ddee0000 - 00000000ddee3000 (ACPI NVS)
[ 0.000000] Xen: 00000000ddee3000 - 00000000ddef0000 (ACPI data)
[ 0.000000] Xen: 00000000ddef0000 - 00000000ddf00000 (reserved)
[ 0.000000] Xen: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] Xen: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.4 present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around
it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable)
==> (reserved)
[ 0.000000] last_pfn = 0x20000 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009f000 (usable)
[ 0.000000] modified: 000000000009f000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 0000000020000000 (usable)
[ 0.000000] modified: 00000000ddee0000 - 00000000ddee3000 (ACPI NVS)
[ 0.000000] modified: 00000000ddee3000 - 00000000ddef0000 (ACPI data)
[ 0.000000] modified: 00000000ddef0000 - 00000000ddf00000 (reserved)
[ 0.000000] modified: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-0000000020000000
[ 0.000000] 0000000000 - 0020000000 page 4k
[ 0.000000] kernel direct mapping tables up to 20000000 @ 100000-202000
[ 0.000000] RAMDISK: 0199a000 - 02054200
[ 0.000000] ACPI: RSDP 00000000000f8210 00024 (v02 ATI )
[ 0.000000] ACPI: XSDT 00000000ddee3100 00044 (v01 ATI ASUSACPI 42302E31
AWRD 00000000)
[ 0.000000] ACPI: FACP 00000000ddee8500 000F4 (v03 ATI ASUSACPI 42302E31
AWRD 00000000)
[ 0.000000] ACPI: DSDT 00000000ddee3280 05210 (v01 ATI ASUSACPI 00001000
MSFT 03000000)
[ 0.000000] ACPI: FACS 00000000ddee0000 00040
[ 0.000000] ACPI: HPET 00000000ddee8740 00038 (v01 ATI ASUSACPI 42302E31
AWRD 00000098)
[ 0.000000] ACPI: MCFG 00000000ddee87c0 0003C (v01 ATI ASUSACPI 42302E31
AWRD 00000000)
[ 0.000000] ACPI: APIC 00000000ddee8640 00084 (v01 ATI ASUSACPI 42302E31
AWRD 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 0020000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000
- 0000001000]
[ 0.000000] #1 [0002156000 - 000216b000] XEN PAGETABLES ==> [0002156000
- 000216b000]
[ 0.000000] #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000
- 0000008000]
[ 0.000000] #3 [0001000000 - 0001979274] TEXT DATA BSS ==> [0001000000
- 0001979274]
[ 0.000000] #4 [000199a000 - 0002054200] RAMDISK ==> [000199a000
- 0002054200]
[ 0.000000] #5 [0002055000 - 0002156000] XEN START INFO ==> [0002055000
- 0002156000]
[ 0.000000] #6 [000197a000 - 000197a155] BRK ==> [000197a000
- 000197a155]
[ 0.000000] #7 [0000100000 - 00001ea000] PGTABLE ==> [0000100000
- 00001ea000]
[ 0.000000] found SMP MP-table at [ffff8800000f6560] f6560
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x00020000
[ 0.000000] On node 0 totalpages: 130959
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 237 pages reserved
[ 0.000000] DMA zone: 3690 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 1736 pages used for memmap
[ 0.000000] DMA32 zone: 125240 pages, LIFO batch:31
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8200 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 20000000 (gap:
20000000:bdee0000)
[ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Allocated 22 4k pages, static data 88032 bytes
[ 0.000000] trying to map vcpu_info 0 at ffffc9000000b020, mfn 21617f,
offset 32
[ 0.000000] cpu 0 using vcpu_info at ffffc9000000b020
[ 0.000000] trying to map vcpu_info 1 at ffffc90000023020, mfn 216195,
offset 32
[ 0.000000] cpu 1 using vcpu_info at ffffc90000023020
[ 0.000000] Xen: using vcpu_info placement
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 128930
[ 0.000000] Kernel command line: root=/dev/mapper/brontus-xen_root ro debug
netconsole=4444@xxxxxxx/eth0,6666@xxxxxxx/00:12:1E:19:D0:BC loglevel=10
[ 0.000000] PID hash table entries: 2048 (order: 11, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Node 0: aperture @ 20000000 size 32 MB
[ 0.000000] Aperture too small (32 MB) than (64 MB)
[ 0.000000] PCI-DMA: Using Xen software bounce buffering for IO (Xen-SWIOTLB)
[ 0.000000] xen_swiotlb_fixup: buf=ffff880002c6c000 size=67108864
[ 0.000000] xen_swiotlb_fixup: buf=ffff880006ccc000 size=32768
[ 0.000000] Placing 64MB Xen software IO TLB between ffff880002c6c000 -
ffff880006c6c000
[ 0.000000] Xen software IO TLB at phys 0x2c6c000 - 0x6c6c000
[ 0.000000] Memory: 430336k/524288k available (5097k kernel code, 452k
absent, 92804k reserved, 2902k data, 568k init)
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2,
Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:424
[ 0.000000] xen: registering gsi 0 triggering 1 polarity 0
[ 0.000000] xen: --> irq=0
[ 0.000000] xen_set_ioapic_routing: irq 0 gsi 0 vector 0 ioapic 0 pin 0
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 1 triggering 1 polarity 0
[ 0.000000] xen: --> irq=1
[ 0.000000] xen_set_ioapic_routing: irq 1 gsi 1 vector 1 ioapic 0 pin 1
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 3 triggering 1 polarity 0
[ 0.000000] xen: --> irq=3
[ 0.000000] xen_set_ioapic_routing: irq 3 gsi 3 vector 3 ioapic 0 pin 3
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 4 triggering 1 polarity 0
[ 0.000000] xen: --> irq=4
[ 0.000000] xen_set_ioapic_routing: irq 4 gsi 4 vector 4 ioapic 0 pin 4
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 5 triggering 1 polarity 0
[ 0.000000] xen: --> irq=5
[ 0.000000] xen_set_ioapic_routing: irq 5 gsi 5 vector 5 ioapic 0 pin 5
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 6 triggering 1 polarity 0
[ 0.000000] xen: --> irq=6
[ 0.000000] xen_set_ioapic_routing: irq 6 gsi 6 vector 6 ioapic 0 pin 6
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 7 triggering 1 polarity 0
[ 0.000000] xen: --> irq=7
[ 0.000000] xen_set_ioapic_routing: irq 7 gsi 7 vector 7 ioapic 0 pin 7
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 8 triggering 1 polarity 0
[ 0.000000] xen: --> irq=8
[ 0.000000] xen_set_ioapic_routing: irq 8 gsi 8 vector 8 ioapic 0 pin 8
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 9 triggering 0 polarity 1
[ 0.000000] xen: --> irq=9
[ 0.000000] xen_set_ioapic_routing: irq 9 gsi 9 vector 9 ioapic 0 pin 9
triggering 1 polarity 1
[ 0.000000] xen: registering gsi 10 triggering 1 polarity 0
[ 0.000000] xen: --> irq=10
[ 0.000000] xen_set_ioapic_routing: irq 10 gsi 10 vector 10 ioapic 0 pin 10
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 11 triggering 1 polarity 0
[ 0.000000] xen: --> irq=11
[ 0.000000] xen_set_ioapic_routing: irq 11 gsi 11 vector 11 ioapic 0 pin 11
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 12 triggering 1 polarity 0
[ 0.000000] xen: --> irq=12
[ 0.000000] xen_set_ioapic_routing: irq 12 gsi 12 vector 12 ioapic 0 pin 12
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 13 triggering 1 polarity 0
[ 0.000000] xen: --> irq=13
[ 0.000000] xen_set_ioapic_routing: irq 13 gsi 13 vector 13 ioapic 0 pin 13
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 14 triggering 1 polarity 0
[ 0.000000] xen: --> irq=14
[ 0.000000] xen_set_ioapic_routing: irq 14 gsi 14 vector 14 ioapic 0 pin 14
triggering 0 polarity 0
[ 0.000000] xen: registering gsi 15 triggering 1 polarity 0
[ 0.000000] xen: --> irq=15
[ 0.000000] xen_set_ioapic_routing: irq 15 gsi 15 vector 15 ioapic 0 pin 15
triggering 0 polarity 0
[ 0.000000] Detected 2399.914 MHz processor.
[ 0.000999] Console: colour VGA+ 80x25
[ 0.000999] console [tty0] enabled
[ 0.000999] Xen: using vcpuop timer interface
[ 0.000999] installing Xen timer for CPU 0
[ 0.000999] alloc irq_desc for 24 on node 0
[ 0.000999] alloc kstat_irqs on node 0
[ 0.000999] Calibrating delay loop (skipped), value calculated using timer
frequency.. 4799.82 BogoMIPS (lpj=2399914)
[ 0.000999] Security Framework initialized
[ 0.000999] SELinux: Initializing.
[ 0.000999] SELinux: Starting in permissive mode
[ 0.000999] Mount-cache hash table entries: 256
[ 0.000999] Initializing cgroup subsys ns
[ 0.000999] Initializing cgroup subsys cpuacct
[ 0.000999] Initializing cgroup subsys freezer
[ 0.000999] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.000999] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.001014] tseg: 00ddf00000
[ 0.001080] CPU: Physical Processor ID: 0
[ 0.001147] CPU: Processor Core ID: 0
[ 0.001218] mce: CPU supports 5 MCE banks
[ 0.001313] Performance Counters: AMD PMU driver.
[ 0.001408] ------------[ cut here ]------------
[ 0.001480] WARNING: at
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/arch/x86/xen/enlighten.c:714
xen_apic_write+0x15/0x17()
[ 0.001586] Hardware name: System Product Name
[ 0.001652] Modules linked in:
[ 0.001745] Pid: 0, comm: swapper Not tainted 2.6.31 #2
[ 0.001812] Call Trace:
[ 0.001882] [<ffffffff8100b361>] ? xen_apic_write+0x15/0x17
[ 0.001953] [<ffffffff8104d22b>] warn_slowpath_common+0x77/0xa4
[ 0.001999] [<ffffffff8104d267>] warn_slowpath_null+0xf/0x11
[ 0.001999] [<ffffffff8100b361>] xen_apic_write+0x15/0x17
[ 0.001999] [<ffffffff8101f09b>] perf_counters_lapic_init+0x2e/0x30
[ 0.001999] [<ffffffff817f113c>] init_hw_perf_counters+0x305/0x3a2
[ 0.001999] [<ffffffff8100f07f>] ? xen_restore_fl_direct_end+0x0/0x1
[ 0.001999] [<ffffffff810dc633>] ? kmem_cache_alloc+0x7b/0xdd
[ 0.001999] [<ffffffff817f0e08>] identify_boot_cpu+0x3c/0x3e
[ 0.001999] [<ffffffff817f0e13>] check_bugs+0x9/0x2d
[ 0.001999] [<ffffffff817e856a>] start_kernel+0x3d7/0x3ec
[ 0.001999] [<ffffffff817e7a9f>] x86_64_start_reservations+0xaa/0xae
[ 0.001999] [<ffffffff817eb8c9>] xen_start_kernel+0x61e/0x625
[ 0.001999] ---[ end trace 4eaa2a86a8e2da22 ]---
[ 0.001999] ... version: 0
[ 0.001999] ... bit width: 48
[ 0.001999] ... generic counters: 4
[ 0.001999] ... value mask: 0000ffffffffffff
[ 0.001999] ... max period: 00007fffffffffff
[ 0.001999] ... fixed-purpose counters: 0
[ 0.001999] ... counter mask: 000000000000000f
[ 0.001999] SMP alternatives: switching to UP code
[ 0.002683] ACPI: Core revision 20090521
[ 0.011105] alloc irq_desc for 25 on node 0
[ 0.011176] alloc kstat_irqs on node 0
[ 0.011250] cpu 0 spinlock event irq 25
[ 0.011319] alloc irq_desc for 26 on node 0
[ 0.011385] alloc kstat_irqs on node 0
[ 0.011455] alloc irq_desc for 27 on node 0
[ 0.011522] alloc kstat_irqs on node 0
[ 0.011592] alloc irq_desc for 28 on node 0
[ 0.011659] alloc kstat_irqs on node 0
[ 0.011731] alloc irq_desc for 29 on node 0
[ 0.011798] alloc kstat_irqs on node 0
[ 0.012061] installing Xen timer for CPU 1
[ 0.012130] alloc irq_desc for 30 on node 0
[ 0.012196] alloc kstat_irqs on node 0
[ 0.012268] alloc irq_desc for 31 on node 0
[ 0.012335] alloc kstat_irqs on node 0
[ 0.012406] cpu 1 spinlock event irq 31
[ 0.012502] SMP alternatives: switching to SMP code
[ 0.012998] alloc irq_desc for 32 on node 0
[ 0.012998] alloc kstat_irqs on node 0
[ 0.013015] alloc irq_desc for 33 on node 0
[ 0.013081] alloc kstat_irqs on node 0
[ 0.013152] alloc irq_desc for 34 on node 0
[ 0.013218] alloc kstat_irqs on node 0
[ 0.013287] alloc irq_desc for 35 on node 0
[ 0.013353] alloc kstat_irqs on node 0
[ 0.000018] Initializing CPU#1
[ 0.000082] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.000086] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.000090] CPU: Physical Processor ID: 0
[ 0.000092] CPU: Processor Core ID: 1
[ 0.000100] mce: CPU supports 5 MCE banks
[ 0.013592] Brought up 2 CPUs
[ 0.014692] Booting paravirtualized kernel on Xen
[ 0.014692] Xen version: 3.5-unstable (preserve-AD) (dom0)
[ 0.015050] Grant table initialized
[ 0.015150] Time: 8:51:59 Date: 09/22/09
[ 0.015301] NET: Registered protocol family 16
[ 0.015420] alloc irq_desc for 36 on node 0
[ 0.015420] alloc kstat_irqs on node 0
[ 0.016038] xenbus_probe_init ok
[ 0.016299] node 0 link 0: io port [c000, ffff]
[ 0.016372] TOM: 00000000e0000000 aka 3584M
[ 0.016440] node 0 link 0: mmio [a0000, bffff]
[ 0.016537] node 0 link 0: mmio [e0000000, dfffffff]
[ 0.016633] node 0 link 0: mmio [f0000000, fe02ffff]
[ 0.016728] node 0 link 0: mmio [e0000000, e03fffff]
[ 0.017022] TOM2: 0000000220000000 aka 8704M
[ 0.017089] bus: [00,03] on node 0 link 0
[ 0.017156] bus: 00 index 0 io port: [0, ffff]
[ 0.017222] bus: 00 index 1 mmio: [a0000, bffff]
[ 0.017289] bus: 00 index 2 mmio: [e0000000, efffffff]
[ 0.017356] bus: 00 index 3 mmio: [f0000000, ffffffff]
[ 0.017423] bus: 00 index 4 mmio: [220000000, fcffffffff]
[ 0.017513] ACPI: bus type pci registered
[ 0.017615] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.017615] PCI: MCFG area at e0000000 reserved in E820
[ 0.086288] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.086363] PCI: Using configuration type 1 for base access
[ 0.100119] bio: create slab <bio-0> at 0
[ 0.102149] ACPI: EC: Look up EC in DSDT
[ 0.114184] ACPI: Interpreter enabled
[ 0.114254] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.114501] ACPI: Using IOAPIC for interrupt routing
[ 0.125358] ACPI: No dock devices found.
[ 0.125606] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.126089] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[ 0.126160] pci 0000:00:07.0: PME# disabled
[ 0.126336] pci 0000:00:12.0: reg 10 io port: [0xff00-0xff07]
[ 0.126413] pci 0000:00:12.0: reg 14 io port: [0xfe00-0xfe03]
[ 0.126490] pci 0000:00:12.0: reg 18 io port: [0xfd00-0xfd07]
[ 0.126568] pci 0000:00:12.0: reg 1c io port: [0xfc00-0xfc03]
[ 0.126645] pci 0000:00:12.0: reg 20 io port: [0xfb00-0xfb0f]
[ 0.126723] pci 0000:00:12.0: reg 24 32bit mmio: [0xfe02f000-0xfe02f3ff]
[ 0.126886] pci 0000:00:13.0: reg 10 32bit mmio: [0xfe02e000-0xfe02efff]
[ 0.127021] pci 0000:00:13.1: reg 10 32bit mmio: [0xfe02d000-0xfe02dfff]
[ 0.127199] pci 0000:00:13.2: reg 10 32bit mmio: [0xfe02c000-0xfe02cfff]
[ 0.127378] pci 0000:00:13.3: reg 10 32bit mmio: [0xfe02b000-0xfe02bfff]
[ 0.127557] pci 0000:00:13.4: reg 10 32bit mmio: [0xfe02a000-0xfe02afff]
[ 0.127772] pci 0000:00:13.5: reg 10 32bit mmio: [0xfe029000-0xfe0290ff]
[ 0.127945] pci 0000:00:13.5: supports D1 D2
[ 0.127980] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
[ 0.127980] pci 0000:00:13.5: PME# disabled
[ 0.128057] pci 0000:00:14.0: reg 10 io port: [0xb00-0xb0f]
[ 0.128262] pci 0000:00:14.1: reg 10 io port: [0x00-0x07]
[ 0.128340] pci 0000:00:14.1: reg 14 io port: [0x00-0x03]
[ 0.128416] pci 0000:00:14.1: reg 18 io port: [0x00-0x07]
[ 0.128493] pci 0000:00:14.1: reg 1c io port: [0x00-0x03]
[ 0.128569] pci 0000:00:14.1: reg 20 io port: [0xf900-0xf90f]
[ 0.129249] pci 0000:01:05.0: reg 10 64bit mmio: [0xfa000000-0xfbffffff]
[ 0.129335] pci 0000:01:05.0: reg 18 64bit mmio: [0xfdbf0000-0xfdbfffff]
[ 0.129412] pci 0000:01:05.0: reg 20 io port: [0xde00-0xdeff]
[ 0.129488] pci 0000:01:05.0: reg 24 32bit mmio: [0xfda00000-0xfdafffff]
[ 0.129595] pci 0000:01:05.0: supports D1 D2
[ 0.129739] pci 0000:00:01.0: bridge io port: [0xd000-0xdfff]
[ 0.129813] pci 0000:00:01.0: bridge 32bit mmio: [0xfda00000-0xfdbfffff]
[ 0.129891] pci 0000:00:01.0: bridge 64bit mmio pref: [0xfa000000-0xfbffffff]
[ 0.129980] pci 0000:02:00.0: reg 10 io port: [0xee00-0xeeff]
[ 0.129980] pci 0000:02:00.0: reg 18 64bit mmio: [0xfdfff000-0xfdffffff]
[ 0.129980] pci 0000:02:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 0.129980] pci 0000:02:00.0: supports D1 D2
[ 0.129980] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.129980] pci 0000:02:00.0: PME# disabled
[ 0.130088] pci 0000:00:07.0: bridge io port: [0xe000-0xefff]
[ 0.130159] pci 0000:00:07.0: bridge 32bit mmio: [0xfdf00000-0xfdffffff]
[ 0.130233] pci 0000:00:07.0: bridge 64bit mmio pref: [0xfdc00000-0xfdcfffff]
[ 0.130423] pci 0000:00:14.4: transparent bridge
[ 0.130495] pci 0000:00:14.4: bridge io port: [0xc000-0xcfff]
[ 0.130567] pci 0000:00:14.4: bridge 32bit mmio: [0xfde00000-0xfdefffff]
[ 0.130639] pci 0000:00:14.4: bridge 32bit mmio pref: [0xfdd00000-0xfddfffff]
[ 0.130733] pci_bus 0000:00: on NUMA node 0
[ 0.130804] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.131395] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 0.131745] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
[ 0.131914] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 0.173113] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0,
disabled.
[ 0.173657] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0,
disabled.
[ 0.174103] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0,
disabled.
[ 0.175102] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0,
disabled.
[ 0.175644] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0,
disabled.
[ 0.176102] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0,
disabled.
[ 0.176643] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11)
[ 0.177073] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0,
disabled.
[ 0.177572] xenbus_probe_backend_init bus registered ok
[ 0.177572] xenbus_probe_frontend_init bus registered ok
[ 0.177572] xen_balloon: Initialising balloon driver.
[ 0.178140] SCSI subsystem initialized
[ 0.178140] libata version 3.00 loaded.
[ 0.179053] usbcore: registered new interface driver usbfs
[ 0.179116] usbcore: registered new interface driver hub
[ 0.179116] usbcore: registered new device driver usb
[ 0.180182] PCI: Using ACPI for IRQ routing
[ 0.180446] IO APIC resources couldn't be allocated.
[ 0.194046] cfg80211: Using static regulatory domain info
[ 0.194058] cfg80211: Regulatory domain: US
[ 0.194124] (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
[ 0.194232] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 0.194305] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.194376] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.194446] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.194516] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.194586] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 0.194667] cfg80211: Calling CRDA for country: US
[ 0.194772] NetLabel: Initializing
[ 0.194772] NetLabel: domain hash size = 128
[ 0.194772] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.194772] NetLabel: unlabeled traffic allowed by default
[ 0.195983] Switched to high resolution mode on CPU 0
[ 0.196210] Switched to high resolution mode on CPU 1
[ 0.202027] pnp: PnP ACPI init
[ 0.202119] ACPI: bus type pnp registered
[ 0.203617] xen: registering gsi 8 triggering 1 polarity 0
[ 0.203686] xen_allocate_pirq: returning irq 8 for gsi 8
[ 0.203752] xen: --> irq=8
[ 0.203819] xen_set_ioapic_routing: irq 8 gsi 8 vector 8 ioapic 0 pin 8
triggering 0 polarity 0
[ 0.204403] xen: registering gsi 13 triggering 1 polarity 0
[ 0.204472] xen_allocate_pirq: returning irq 13 for gsi 13
[ 0.204539] xen: --> irq=13
[ 0.204605] xen_set_ioapic_routing: irq 13 gsi 13 vector 13 ioapic 0 pin 13
triggering 0 polarity 0
[ 0.207199] pnp: PnP ACPI: found 10 devices
[ 0.207268] ACPI: ACPI bus type pnp unregistered
[ 0.207351] system 00:01: ioport range 0x4100-0x411f has been reserved
[ 0.207419] system 00:01: ioport range 0x228-0x22f has been reserved
[ 0.207486] system 00:01: ioport range 0x40b-0x40b has been reserved
[ 0.207553] system 00:01: ioport range 0x4d6-0x4d6 has been reserved
[ 0.207621] system 00:01: ioport range 0xc00-0xc01 has been reserved
[ 0.207688] system 00:01: ioport range 0xc14-0xc14 has been reserved
[ 0.207755] system 00:01: ioport range 0xc50-0xc52 has been reserved
[ 0.207823] system 00:01: ioport range 0xc6c-0xc6d has been reserved
[ 0.207890] system 00:01: ioport range 0xc6f-0xc6f has been reserved
[ 0.207958] system 00:01: ioport range 0xcd0-0xcd1 has been reserved
[ 0.208026] system 00:01: ioport range 0xcd2-0xcd3 has been reserved
[ 0.208093] system 00:01: ioport range 0xcd4-0xcdf has been reserved
[ 0.208160] system 00:01: ioport range 0x4000-0x40fe has been reserved
[ 0.208172] system 00:01: ioport range 0x4210-0x4217 has been reserved
[ 0.208172] system 00:01: ioport range 0xb10-0xb1f has been reserved
[ 0.208172] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 0.208172] system 00:07: ioport range 0x220-0x225 has been reserved
[ 0.208172] system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.208172] system 00:09: iomem range 0xcd600-0xcffff could not be reserved
[ 0.208172] system 00:09: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.208172] system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.208172] system 00:09: iomem range 0xfc000-0xfffff could not be reserved
[ 0.208172] system 00:09: iomem range 0xddef0000-0xddfeffff could not be
reserved
[ 0.208172] system 00:09: iomem range 0xfed00000-0xfed000ff has been reserved
[ 0.208172] system 00:09: iomem range 0xddee0000-0xddefffff could not be
reserved
[ 0.208172] system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
[ 0.208172] system 00:09: iomem range 0x0-0x9ffff could not be reserved
[ 0.208172] system 00:09: iomem range 0x100000-0xddedffff could not be
reserved
[ 0.208172] system 00:09: iomem range 0xddff0000-0xdffeffff has been reserved
[ 0.208172] system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.208172] system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.208172] system 00:09: iomem range 0xfff80000-0xfffeffff has been reserved
[ 0.215470] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.215541] pci 0000:00:01.0: IO window: 0xd000-0xdfff
[ 0.215612] pci 0000:00:01.0: MEM window: 0xfda00000-0xfdbfffff
[ 0.215683] pci 0000:00:01.0: PREFETCH window:
0x000000fa000000-0x000000fbffffff
[ 0.215797] pci 0000:00:07.0: PCI bridge, secondary bus 0000:02
[ 0.215866] pci 0000:00:07.0: IO window: 0xe000-0xefff
[ 0.215937] pci 0000:00:07.0: MEM window: 0xfdf00000-0xfdffffff
[ 0.216002] pci 0000:00:07.0: PREFETCH window:
0x000000fdc00000-0x000000fdcfffff
[ 0.216002] pci 0000:00:14.4: PCI bridge, secondary bus 0000:03
[ 0.216002] pci 0000:00:14.4: IO window: 0xc000-0xcfff
[ 0.216002] pci 0000:00:14.4: MEM window: 0xfde00000-0xfdefffff
[ 0.216002] pci 0000:00:14.4: PREFETCH window: 0xfdd00000-0xfddfffff
[ 0.216002] pci 0000:00:07.0: setting latency timer to 64
[ 0.216002] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.216002] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.216002] pci_bus 0000:01: resource 0 io: [0xd000-0xdfff]
[ 0.216002] pci_bus 0000:01: resource 1 mem: [0xfda00000-0xfdbfffff]
[ 0.216002] pci_bus 0000:01: resource 2 pref mem [0xfa000000-0xfbffffff]
[ 0.216002] pci_bus 0000:02: resource 0 io: [0xe000-0xefff]
[ 0.216002] pci_bus 0000:02: resource 1 mem: [0xfdf00000-0xfdffffff]
[ 0.216002] pci_bus 0000:02: resource 2 pref mem [0xfdc00000-0xfdcfffff]
[ 0.216002] pci_bus 0000:03: resource 0 io: [0xc000-0xcfff]
[ 0.216002] pci_bus 0000:03: resource 1 mem: [0xfde00000-0xfdefffff]
[ 0.216002] pci_bus 0000:03: resource 2 pref mem [0xfdd00000-0xfddfffff]
[ 0.216002] pci_bus 0000:03: resource 3 io: [0x00-0xffff]
[ 0.216002] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.217435] NET: Registered protocol family 2
[ 0.217636] IP route cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.218227] TCP established hash table entries: 65536 (order: 8, 1048576
bytes)
[ 0.218758] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.219365] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.219439] TCP reno registered
[ 0.219662] NET: Registered protocol family 1
[ 0.219824] Trying to unpack rootfs image as initramfs...
[ 0.230681] Freeing initrd memory: 6888k freed
[ 0.237071] Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>,
Peter Oruba
[ 0.237185] Scanning for low memory corruption every 60 seconds
[ 0.237776] audit: initializing netlink socket (disabled)
[ 0.237864] type=2000 audit(1253609519.993:1): initialized
[ 0.245445] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.251181] VFS: Disk quotas dquot_6.5.2
[ 0.251435] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.254044] msgmni has been set to 855
[ 0.254411] SELinux: Registering netfilter hooks
[ 0.255264] alg: No test for stdrng (krng)
[ 0.255568] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
252)
[ 0.255674] io scheduler noop registered
[ 0.255740] io scheduler anticipatory registered
[ 0.255807] io scheduler deadline registered
[ 0.255886] io scheduler cfq registered (default)
[ 0.472067] pci 0000:01:05.0: Boot video device
[ 0.472476] alloc irq_desc for 37 on node 0
[ 0.472543] alloc kstat_irqs on node 0
[ 0.472639] pcieport-driver 0000:00:07.0: setting latency timer to 64
[ 0.473127] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.473758] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.473866] ACPI: Power Button [PWRF]
[ 0.474094] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.474200] ACPI: Power Button [PWRB]
[ 0.474490] fan PNP0C0B:00: registered as cooling_device0
[ 0.474566] ACPI: Fan [FAN] (on)
[ 0.475022] processor LNXCPU:00: registered as cooling_device1
[ 0.475243] processor LNXCPU:01: registered as cooling_device2
[ 0.475451] processor LNXCPU:02: registered as cooling_device3
[ 0.475658] processor LNXCPU:03: registered as cooling_device4
[ 0.479944] ACPI Warning: \_TZ_.THRM._PSL: Return Package type mismatch at
index 0 - found [NULL Object Descriptor], expected Reference 20090521
nspredef-946
[ 0.480003] ACPI: Expecting a [Reference] package element, found type 0
[ 0.480003] ACPI: Invalid passive threshold
[ 0.480721] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.480809] ACPI: Thermal Zone [THRM] (40 C)
[ 0.481131] Event-channel device installed.
[ 0.485298] registering netback
[ 0.492220] alloc irq_desc for 38 on node 0
[ 0.492293] alloc kstat_irqs on node 0
[ 0.493427] hpet_acpi_add: no address or irqs in _CRS
[ 0.493686] Non-volatile memory driver v1.3
[ 0.493955] Linux agpgart interface v0.103
[ 0.494281] [drm] Initialized drm 1.1.0 20060810
[ 0.494508] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.499373] brd: module loaded
[ 0.501396] loop: module loaded
[ 0.501689] input: Macintosh mouse button emulation as
/devices/virtual/input/input2
[ 0.502407] ahci 0000:00:12.0: version 3.0
[ 0.502495] xen: registering gsi 22 triggering 0 polarity 1
[ 0.502565] alloc irq_desc for 22 on node 0
[ 0.503349] alloc kstat_irqs on node 0
[ 0.505513] xen: --> irq=22
[ 0.505580] xen_set_ioapic_routing: irq 22 gsi 22 vector 22 ioapic 0 pin 22
triggering 1 polarity 1
[ 0.505696] ahci 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 0.505885] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf
impl SATA mode
[ 0.505992] ahci 0000:00:12.0: flags: 64bit ncq sntf ilck pm led clo pmp pio
slum part
[ 0.506973] scsi0 : ahci
[ 0.507523] scsi1 : ahci
[ 0.507822] scsi2 : ahci
[ 0.508132] scsi3 : ahci
[ 0.508634] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100
irq 22
[ 0.508745] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180
irq 22
[ 0.508856] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200
irq 22
[ 0.508965] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280
irq 22
[ 0.509326] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 0.509421] xen: registering gsi 19 triggering 0 polarity 1
[ 0.509495] alloc irq_desc for 19 on node 0
[ 0.509564] alloc kstat_irqs on node 0
[ 0.509635] xen: --> irq=19
[ 0.509704] xen_set_ioapic_routing: irq 19 gsi 19 vector 19 ioapic 0 pin 19
triggering 1 polarity 1
[ 0.509824] r8169 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 0.509964] r8169 0000:02:00.0: setting latency timer to 64
[ 0.510100] alloc irq_desc for 39 on node 0
[ 0.510100] alloc kstat_irqs on node 0
[ 0.510834] eth0: RTL8168b/8111b at 0xffffc9000007e000, 00:1b:fc:86:73:27,
XID 38000000 IRQ 39
[ 0.512532] netconsole: local port 4444
[ 0.512600] netconsole: local IP 1.2.3.4
[ 0.512666] netconsole: interface eth0
[ 0.512732] netconsole: remote port 6666
[ 0.512798] netconsole: remote IP 1.2.3.5
[ 0.512864] netconsole: remote ethernet address 00:12:1e:19:d0:bc
[ 0.512932] netconsole: device eth0 not up yet, forcing it
[ 0.513449] r8169: eth0: link down
[ 0.513637] r8169: eth0: link down
[ 0.814306] ata2: SATA link down (SStatus 0 SControl 300)
[ 0.966026] ata1: softreset failed (device not ready)
[ 0.966095] ata1: applying SB600 PMP SRST workaround and retrying
[ 0.967268] ata3: softreset failed (device not ready)
[ 0.967336] ata3: applying SB600 PMP SRST workaround and retrying
[ 0.968269] ata4: softreset failed (device not ready)
[ 0.968337] ata4: applying SB600 PMP SRST workaround and retrying
[ 1.119035] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.120278] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.121280] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.148058] ata1.00: ATA-8: ST3500320NS, SN06, max UDMA/133
[ 1.148129] ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 1.148211] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.149321] ata3.00: ATA-8: ST3500320NS, SN06, max UDMA/133
[ 1.149389] ata3.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 1.149470] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.150260] ata4.00: ATA-8: ST3500320NS, SN06, max UDMA/133
[ 1.150327] ata4.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 1.150408] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.190547] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.190616] ata1.00: configured for UDMA/133
[ 1.191801] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.191870] ata3.00: configured for UDMA/133
[ 1.192677] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.192745] ata4.00: configured for UDMA/133
[ 1.201164] scsi 0:0:0:0: Direct-Access ATA ST3500320NS SN06
PQ: 0 ANSI: 5
[ 1.201799] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465
GiB)
[ 1.201866] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.202146] scsi 2:0:0:0: Direct-Access ATA ST3500320NS SN06
PQ: 0 ANSI: 5
[ 1.202149] sd 0:0:0:0: [sda] Write Protect is off
[ 1.202155] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.202211] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.202485] sda:
[ 1.202913] sd 2:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465
GiB)
[ 1.203185] sd 2:0:0:0: [sdb] Write Protect is off
[ 1.203255] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.203382] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.203755] sdb:
[ 1.203994] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 1.204355] scsi 3:0:0:0: Direct-Access ATA ST3500320NS SN06
PQ: 0 ANSI: 5
[ 1.204879] sd 3:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465
GiB)
[ 1.205091] sd 3:0:0:0: [sdc] Write Protect is off
[ 1.205159] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1.205313] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.205660] sdc:
[ 1.205918] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 1.216527] sda1 sda4
[ 1.217357] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.219995] sdb1 sdb4
[ 1.220772] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 1.223383] sdc1 sdc4
[ 1.224200] sd 3:0:0:0: [sdc] Attached SCSI disk
[ 2.147642] r8169: eth0: link up
[ 2.153019] console [netcon0] enabled
[ 2.154004] netconsole: network logging started
[ 2.207689] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.207767] ehci_hcd: block sizes: qh 192 qtd 96 itd 192 sitd 96
[ 2.207891] xen: registering gsi 19 triggering 0 polarity 1
[ 2.207963] xen_allocate_pirq: returning irq 19 for gsi 19
[ 2.208035] xen: --> irq=19
[ 2.208106] xen_set_ioapic_routing: irq 19 gsi 19 vector 19 ioapic 0 pin 19
triggering 1 polarity 1
[ 2.208227] ehci_hcd 0000:00:13.5: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 2.208328] ehci_hcd 0000:00:13.5: EHCI Host Controller
[ 2.208454]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file 'devices'
[ 2.208580]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '001'
[ 2.208817] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus
number 1
[ 2.208945] ehci_hcd 0000:00:13.5: reset hcs_params 0x10520a dbg=1 cc=5
pcc=2 ordered !ppc ports=10
[ 2.209059] ehci_hcd 0000:00:13.5: reset hcc_params a072 thresh 7 uframes
256/512/1024
[ 2.209240] ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze
workaround
[ 2.209366] ehci_hcd 0000:00:13.5: reset command 080002 (park)=0 ithresh=8
period=1024 Reset HALT
[ 2.209497] ehci_hcd 0000:00:13.5: debug port 1
[ 2.209581] ehci_hcd 0000:00:13.5: MWI active
[ 2.209652] ehci_hcd 0000:00:13.5: supports USB remote wakeup
[ 2.209754] ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000
[ 2.209805] ehci_hcd 0000:00:13.5: reset command 080002 (park)=0 ithresh=8
period=1024 Reset HALT
[ 2.209805] ehci_hcd 0000:00:13.5: init command 010009 (park)=0 ithresh=1
period=256 RUN
[ 2.216018] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00
[ 2.216162] usb usb1: default language 0x0409
[ 2.216253] usb usb1: udev 1, busnum 1, minor = 0
[ 2.216324] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.216395] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.216501] usb usb1: Product: EHCI Host Controller
[ 2.216571] usb usb1: Manufacturer: Linux 2.6.31 ehci_hcd
[ 2.216640] usb usb1: SerialNumber: 0000:00:13.5
[ 2.216781] usb usb1: uevent
[ 2.216959] usb usb1: usb_probe_device
[ 2.217032] usb usb1: configuration #1 chosen from 1 choice
[ 2.217131] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 2.217233] usb 1-0:1.0: uevent
[ 2.217394] hub 1-0:1.0: usb_probe_interface
[ 2.217465] hub 1-0:1.0: usb_probe_interface - got id
[ 2.217536] hub 1-0:1.0: USB hub found
[ 2.217641] hub 1-0:1.0: 10 ports detected
[ 2.217712] hub 1-0:1.0: standalone hub
[ 2.217781] hub 1-0:1.0: no power switching (usb 1.0)
[ 2.217850] hub 1-0:1.0: individual port over-current protection
[ 2.217920] hub 1-0:1.0: power on to power good time: 20ms
[ 2.218018] hub 1-0:1.0: local power source is good
[ 2.218090] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 2.218245]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '001'
[ 2.218492] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.218563] ohci_hcd: block sizes: ed 80 td 96
[ 2.218671] xen: registering gsi 16 triggering 0 polarity 1
[ 2.218745] alloc irq_desc for 16 on node 0
[ 2.218815] alloc kstat_irqs on node 0
[ 2.218894] xen: --> irq=16
[ 2.218964] xen_set_ioapic_routing: irq 16 gsi 16 vector 16 ioapic 0 pin 16
triggering 1 polarity 1
[ 2.219081] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.219170] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 2.219276]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '002'
[ 2.219512] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus
number 2
[ 2.219666] ohci_hcd 0000:00:13.0: created debug files
[ 2.219739] ohci_hcd 0000:00:13.0: supports USB remote wakeup
[ 2.219836] ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000
[ 2.274046] ohci_hcd 0000:00:13.0: OHCI controller state
[ 2.274119] ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
[ 2.274193] ohci_hcd 0000:00:13.0: control 0x283 RWC HCFS=operational CBSR=3
[ 2.274265] ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
[ 2.274336] ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
[ 2.274408] ohci_hcd 0000:00:13.0: intrenable 0x8000001a MIE UE RD WDH
[ 2.274486] ohci_hcd 0000:00:13.0: hcca frame #0005
[ 2.274557] ohci_hcd 0000:00:13.0: roothub.a 02000202 POTPGT=2 NPS NDP=2(2)
[ 2.274628] ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
[ 2.274700] ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
[ 2.274772] ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
[ 2.274845] ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00000100 PPS
[ 2.274952] usb usb2: default language 0x0409
[ 2.275050] usb usb2: udev 1, busnum 2, minor = 128
[ 2.275121] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.275192] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.275300] usb usb2: Product: OHCI Host Controller
[ 2.275370] usb usb2: Manufacturer: Linux 2.6.31 ohci_hcd
[ 2.275439] usb usb2: SerialNumber: 0000:00:13.0
[ 2.275575] usb usb2: uevent
[ 2.275739] usb usb2: usb_probe_device
[ 2.275810] usb usb2: configuration #1 chosen from 1 choice
[ 2.275896] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 2.275995] usb 2-0:1.0: uevent
[ 2.276159] hub 2-0:1.0: usb_probe_interface
[ 2.276230] hub 2-0:1.0: usb_probe_interface - got id
[ 2.276300] hub 2-0:1.0: USB hub found
[ 2.276408] hub 2-0:1.0: 2 ports detected
[ 2.276479] hub 2-0:1.0: standalone hub
[ 2.276548] hub 2-0:1.0: no power switching (usb 1.0)
[ 2.276617] hub 2-0:1.0: global over-current protection
[ 2.276686] hub 2-0:1.0: power on to power good time: 4ms
[ 2.276775] hub 2-0:1.0: local power source is good
[ 2.276844] hub 2-0:1.0: no over-current condition exists
[ 2.276915] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 2.277031]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '001'
[ 2.277205] xen: registering gsi 17 triggering 0 polarity 1
[ 2.277280] alloc irq_desc for 17 on node 0
[ 2.277350] alloc kstat_irqs on node 0
[ 2.277429] xen: --> irq=17
[ 2.277499] xen_set_ioapic_routing: irq 17 gsi 17 vector 17 ioapic 0 pin 17
triggering 1 polarity 1
[ 2.277615] ohci_hcd 0000:00:13.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 2.277702] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 2.277786]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '003'
[ 2.278034] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus
number 3
[ 2.280993] ohci_hcd 0000:00:13.1: created debug files
[ 2.281069] ohci_hcd 0000:00:13.1: supports USB remote wakeup
[ 2.281164] ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000
[ 2.318029] ehci_hcd 0000:00:13.5: GetStatus port 1 status 001803 POWER
sig=j CSC CONNECT
[ 2.318142] hub 1-0:1.0: port 1: status 0501 change 0001
[ 2.318229] ehci_hcd 0000:00:13.5: GetStatus port 2 status 001803 POWER
sig=j CSC CONNECT
[ 2.318340] hub 1-0:1.0: port 2: status 0501 change 0001
[ 2.335045] ohci_hcd 0000:00:13.1: OHCI controller state
[ 2.335118] ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers
[ 2.335191] ohci_hcd 0000:00:13.1: control 0x283 RWC HCFS=operational CBSR=3
[ 2.335264] ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0
[ 2.335335] ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF
[ 2.335405] ohci_hcd 0000:00:13.1: intrenable 0x8000001a MIE UE RD WDH
[ 2.335483] ohci_hcd 0000:00:13.1: hcca frame #0005
[ 2.335553] ohci_hcd 0000:00:13.1: roothub.a 02000202 POTPGT=2 NPS NDP=2(2)
[ 2.335624] ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000
[ 2.335695] ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE
[ 2.335766] ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00000100 PPS
[ 2.335838] ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS
[ 2.335943] usb usb3: default language 0x0409
[ 2.336041] usb usb3: udev 1, busnum 3, minor = 256
[ 2.336111] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.336182] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.336292] usb usb3: Product: OHCI Host Controller
[ 2.336365] usb usb3: Manufacturer: Linux 2.6.31 ohci_hcd
[ 2.336436] usb usb3: SerialNumber: 0000:00:13.1
[ 2.336572] usb usb3: uevent
[ 2.336736] usb usb3: usb_probe_device
[ 2.336811] usb usb3: configuration #1 chosen from 1 choice
[ 2.336900] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 2.337014] usb 3-0:1.0: uevent
[ 2.337175] hub 3-0:1.0: usb_probe_interface
[ 2.337249] hub 3-0:1.0: usb_probe_interface - got id
[ 2.337325] hub 3-0:1.0: USB hub found
[ 2.337440] hub 3-0:1.0: 2 ports detected
[ 2.337513] hub 3-0:1.0: standalone hub
[ 2.337585] hub 3-0:1.0: no power switching (usb 1.0)
[ 2.337656] hub 3-0:1.0: global over-current protection
[ 2.337727] hub 3-0:1.0: power on to power good time: 4ms
[ 2.337818] hub 3-0:1.0: local power source is good
[ 2.337892] hub 3-0:1.0: no over-current condition exists
[ 2.337964] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 2.338083]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '001'
[ 2.338259] xen: registering gsi 18 triggering 0 polarity 1
[ 2.338335] alloc irq_desc for 18 on node 0
[ 2.338403] alloc kstat_irqs on node 0
[ 2.338483] xen: --> irq=18
[ 2.338552] xen_set_ioapic_routing: irq 18 gsi 18 vector 18 ioapic 0 pin 18
triggering 1 polarity 1
[ 2.338668] ohci_hcd 0000:00:13.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.338755] ohci_hcd 0000:00:13.2: OHCI Host Controller
[ 2.338839]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '004'
[ 2.339091] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus
number 4
[ 2.339251] ohci_hcd 0000:00:13.2: created debug files
[ 2.339324] ohci_hcd 0000:00:13.2: supports USB remote wakeup
[ 2.339420] ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000
[ 2.376052] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 2.394045] ohci_hcd 0000:00:13.2: OHCI controller state
[ 2.394118] ohci_hcd 0000:00:13.2: OHCI 1.0, NO legacy support registers
[ 2.394191] ohci_hcd 0000:00:13.2: control 0x283 RWC HCFS=operational CBSR=3
[ 2.394263] ohci_hcd 0000:00:13.2: cmdstatus 0x00000 SOC=0
[ 2.394334] ohci_hcd 0000:00:13.2: intrstatus 0x00000004 SF
[ 2.394405] ohci_hcd 0000:00:13.2: intrenable 0x8000001a MIE UE RD WDH
[ 2.394483] ohci_hcd 0000:00:13.2: hcca frame #0005
[ 2.394554] ohci_hcd 0000:00:13.2: roothub.a 02000202 POTPGT=2 NPS NDP=2(2)
[ 2.394626] ohci_hcd 0000:00:13.2: roothub.b 00000000 PPCM=0000 DR=0000
[ 2.394697] ohci_hcd 0000:00:13.2: roothub.status 00008000 DRWE
[ 2.394769] ohci_hcd 0000:00:13.2: roothub.portstatus [0] 0x00000100 PPS
[ 2.394841] ohci_hcd 0000:00:13.2: roothub.portstatus [1] 0x00000100 PPS
[ 2.394951] usb usb4: default language 0x0409
[ 2.395050] usb usb4: udev 1, busnum 4, minor = 384
[ 2.395122] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.395193] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.395301] usb usb4: Product: OHCI Host Controller
[ 2.395370] usb usb4: Manufacturer: Linux 2.6.31 ohci_hcd
[ 2.395439] usb usb4: SerialNumber: 0000:00:13.2
[ 2.395579] usb usb4: uevent
[ 2.395737] usb usb4: usb_probe_device
[ 2.395807] usb usb4: configuration #1 chosen from 1 choice
[ 2.395893] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[ 2.395992] usb 4-0:1.0: uevent
[ 2.396156] hub 4-0:1.0: usb_probe_interface
[ 2.396226] hub 4-0:1.0: usb_probe_interface - got id
[ 2.396297] hub 4-0:1.0: USB hub found
[ 2.396401] hub 4-0:1.0: 2 ports detected
[ 2.396472] hub 4-0:1.0: standalone hub
[ 2.396542] hub 4-0:1.0: no power switching (usb 1.0)
[ 2.396611] hub 4-0:1.0: global over-current protection
[ 2.396681] hub 4-0:1.0: power on to power good time: 4ms
[ 2.396767] hub 4-0:1.0: local power source is good
[ 2.396836] hub 4-0:1.0: no over-current condition exists
[ 2.396906] hub 4-0:1.0: trying to enable port power on non-switchable hub
[ 2.397026]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '001'
[ 2.397197] xen: registering gsi 17 triggering 0 polarity 1
[ 2.397269] xen_allocate_pirq: returning irq 17 for gsi 17
[ 2.397340] xen: --> irq=17
[ 2.397409] xen_set_ioapic_routing: irq 17 gsi 17 vector 17 ioapic 0 pin 17
triggering 1 polarity 1
[ 2.397529] ohci_hcd 0000:00:13.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 2.397615] ohci_hcd 0000:00:13.3: OHCI Host Controller
[ 2.397700]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '005'
[ 2.397938] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus
number 5
[ 2.398099] ohci_hcd 0000:00:13.3: created debug files
[ 2.398171] ohci_hcd 0000:00:13.3: supports USB remote wakeup
[ 2.398248] ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000
[ 2.418038] hub 1-0:1.0: state 7 ports 10 chg 0006 evt 0000
[ 2.418124] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[ 2.453047] ohci_hcd 0000:00:13.3: OHCI controller state
[ 2.453122] ohci_hcd 0000:00:13.3: OHCI 1.0, NO legacy support registers
[ 2.453194] ohci_hcd 0000:00:13.3: control 0x283 RWC HCFS=operational CBSR=3
[ 2.453266] ohci_hcd 0000:00:13.3: cmdstatus 0x00000 SOC=0
[ 2.453337] ohci_hcd 0000:00:13.3: intrstatus 0x00000004 SF
[ 2.453409] ohci_hcd 0000:00:13.3: intrenable 0x8000001a MIE UE RD WDH
[ 2.453487] ohci_hcd 0000:00:13.3: hcca frame #0005
[ 2.453559] ohci_hcd 0000:00:13.3: roothub.a 02000202 POTPGT=2 NPS NDP=2(2)
[ 2.453630] ohci_hcd 0000:00:13.3: roothub.b 00000000 PPCM=0000 DR=0000
[ 2.453701] ohci_hcd 0000:00:13.3: roothub.status 00008000 DRWE
[ 2.453774] ohci_hcd 0000:00:13.3: roothub.portstatus [0] 0x00000100 PPS
[ 2.453846] ohci_hcd 0000:00:13.3: roothub.portstatus [1] 0x00000100 PPS
[ 2.453951] usb usb5: default language 0x0409
[ 2.454075] usb usb5: udev 1, busnum 5, minor = 512
[ 2.454146] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.454217] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.454324] usb usb5: Product: OHCI Host Controller
[ 2.454393] usb usb5: Manufacturer: Linux 2.6.31 ohci_hcd
[ 2.454462] usb usb5: SerialNumber: 0000:00:13.3
[ 2.454599] usb usb5: uevent
[ 2.454759] usb usb5: usb_probe_device
[ 2.454830] usb usb5: configuration #1 chosen from 1 choice
[ 2.454915] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[ 2.455024] usb 5-0:1.0: uevent
[ 2.455181] hub 5-0:1.0: usb_probe_interface
[ 2.455252] hub 5-0:1.0: usb_probe_interface - got id
[ 2.455323] hub 5-0:1.0: USB hub found
[ 2.455427] hub 5-0:1.0: 2 ports detected
[ 2.455498] hub 5-0:1.0: standalone hub
[ 2.455568] hub 5-0:1.0: no power switching (usb 1.0)
[ 2.455637] hub 5-0:1.0: global over-current protection
[ 2.455706] hub 5-0:1.0: power on to power good time: 4ms
[ 2.455793] hub 5-0:1.0: local power source is good
[ 2.455862] hub 5-0:1.0: no over-current condition exists
[ 2.455932] hub 5-0:1.0: trying to enable port power on non-switchable hub
[ 2.456053]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '001'
[ 2.456222] xen: registering gsi 18 triggering 0 polarity 1
[ 2.456293] xen_allocate_pirq: returning irq 18 for gsi 18
[ 2.456363] xen: --> irq=18
[ 2.456432] xen_set_ioapic_routing: irq 18 gsi 18 vector 18 ioapic 0 pin 18
triggering 1 polarity 1
[ 2.456550] ohci_hcd 0000:00:13.4: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.456637] ohci_hcd 0000:00:13.4: OHCI Host Controller
[ 2.456724]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '006'
[ 2.456966] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus
number 6
[ 2.457127] ohci_hcd 0000:00:13.4: created debug files
[ 2.457199] ohci_hcd 0000:00:13.4: supports USB remote wakeup
[ 2.457277] ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000
[ 2.469285] ehci_hcd 0000:00:13.5: port 1 high speed
[ 2.469360] ehci_hcd 0000:00:13.5: GetStatus port 1 status 001005 POWER
sig=se0 PE CONNECT
[ 2.512048] ohci_hcd 0000:00:13.4: OHCI controller state
[ 2.512121] ohci_hcd 0000:00:13.4: OHCI 1.0, NO legacy support registers
[ 2.512194] ohci_hcd 0000:00:13.4: control 0x283 RWC HCFS=operational CBSR=3
[ 2.512265] ohci_hcd 0000:00:13.4: cmdstatus 0x00000 SOC=0
[ 2.512337] ohci_hcd 0000:00:13.4: intrstatus 0x00000004 SF
[ 2.512408] ohci_hcd 0000:00:13.4: intrenable 0x8000001a MIE UE RD WDH
[ 2.512486] ohci_hcd 0000:00:13.4: hcca frame #0005
[ 2.513003] ohci_hcd 0000:00:13.4: roothub.a 02000202 POTPGT=2 NPS NDP=2(2)
[ 2.513003] ohci_hcd 0000:00:13.4: roothub.b 00000000 PPCM=0000 DR=0000
[ 2.513003] ohci_hcd 0000:00:13.4: roothub.status 00008000 DRWE
[ 2.513003] ohci_hcd 0000:00:13.4: roothub.portstatus [0] 0x00000100 PPS
[ 2.513003] ohci_hcd 0000:00:13.4: roothub.portstatus [1] 0x00000100 PPS
[ 2.515753] usb usb6: default language 0x0409
[ 2.515843] usb usb6: udev 1, busnum 6, minor = 640
[ 2.515912] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.515984] usb usb6: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.516091] usb usb6: Product: OHCI Host Controller
[ 2.516160] usb usb6: Manufacturer: Linux 2.6.31 ohci_hcd
[ 2.516230] usb usb6: SerialNumber: 0000:00:13.4
[ 2.516377] usb usb6: uevent
[ 2.516537] usb usb6: usb_probe_device
[ 2.516608] usb usb6: configuration #1 chosen from 1 choice
[ 2.516693] usb usb6: adding 6-0:1.0 (config #1, interface 0)
[ 2.516792] usb 6-0:1.0: uevent
[ 2.516948] hub 6-0:1.0: usb_probe_interface
[ 2.517019] hub 6-0:1.0: usb_probe_interface - got id
[ 2.517089] hub 6-0:1.0: USB hub found
[ 2.517201] hub 6-0:1.0: 2 ports detected
[ 2.517273] hub 6-0:1.0: standalone hub
[ 2.517343] hub 6-0:1.0: no power switching (usb 1.0)
[ 2.517412] hub 6-0:1.0: global over-current protection
[ 2.517481] hub 6-0:1.0: power on to power good time: 4ms
[ 2.517569] hub 6-0:1.0: local power source is good
[ 2.517638] hub 6-0:1.0: no over-current condition exists
[ 2.517709] hub 6-0:1.0: trying to enable port power on non-switchable hub
[ 2.517815]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '001'
[ 2.518072] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.518548] usbcore: registered new interface driver usblp
[ 2.518621] Initializing USB Mass Storage driver...
[ 2.518801] usbcore: registered new interface driver usb-storage
[ 2.518874] USB Mass Storage support registered.
[ 2.519059] usbcore: registered new interface driver libusual
[ 2.519508] PNP: No PS/2 controller found. Probing ports directly.
[ 2.520155] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.520232] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.520291] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 2.520579] mice: PS/2 mouse device common for all mice
[ 2.521250] rtc_cmos 00:04: RTC can wake from S4
[ 2.521460] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 2.521580] rtc0: alarms up to one month, 242 bytes nvram
[ 2.521896] it87: Found IT8716F chip at 0x228, revision 1
[ 2.521989] it87: in3 is VCC (+5V)
[ 2.522062] it87: in7 is VCCH (+5V Stand-By)
[ 2.522321] ACPI: I/O resource it87 [0x22d-0x22e] conflicts with ACPI region
IP__ [0x22d-0x22e]
[ 2.522434] ACPI: Device needs an ACPI driver
[ 2.522617] k8temp 0000:00:18.3: Temperature readouts might be wrong - check
erratum #141
[ 2.522959] md: raid1 personality registered for level 1
[ 2.523504] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised:
dm-devel@xxxxxxxxxx
[ 2.523857] cpuidle: using governor ladder
[ 2.523930] cpuidle: using governor menu
[ 2.526630] usbcore: registered new interface driver hiddev
[ 2.526804] usbcore: registered new interface driver usbhid
[ 2.526876] usbhid: v2.6:USB HID core driver
[ 2.527177] Netfilter messages via NETLINK v0.30.
[ 2.527282] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 2.527782] ctnetlink v0.93: registering with nfnetlink.
[ 2.529421] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.529530] TCP cubic registered
[ 2.529599] Initializing XFRM netlink socket
[ 2.530174] NET: Registered protocol family 10
[ 2.533243] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.533431] IPv6 over IPv4 tunneling driver
[ 2.535164] NET: Registered protocol family 17
[ 2.535710] RPC: Registered udp transport module.
[ 2.535781] RPC: Registered tcp transport module.
[ 2.536254] PM: Resume from disk failed.
[ 2.536367] registered taskstats version 1
[ 2.536602] Magic number: 9:856:877
[ 2.536915] Freeing unused kernel memory: 568k freed
[ 2.537304] Write protecting the kernel read-only data: 7344k
[ 2.571303] ehci_hcd 0000:00:13.5: port 1 high speed
[ 2.571390] ehci_hcd 0000:00:13.5: GetStatus port 1 status 001005 POWER
sig=se0 PE CONNECT
[ 2.636518] usb 1-1: default language 0x0409
[ 2.638893] usb 1-1: udev 2, busnum 1, minor = 1
[ 2.638964] usb 1-1: New USB device found, idVendor=1005, idProduct=b113
[ 2.639038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.639114] usb 1-1: Product: USB FLASH DRIVE
[ 2.639117] usb 1-1: Manufacturer:
[ 2.639120] usb 1-1: SerialNumber: 1968050104CA
[ 2.639231] usb 1-1: uevent
[ 2.639532] usb 1-1: usb_probe_device
[ 2.639607] usb 1-1: configuration #1 chosen from 1 choice
[ 2.639897] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 2.640016] usb 1-1:1.0: uevent
[ 2.640198] usb-storage 1-1:1.0: usb_probe_interface
[ 2.640282] usb-storage 1-1:1.0: usb_probe_interface - got id
[ 2.647884] scsi4 : SCSI emulation for USB Mass Storage devices
[ 2.656535] usb-storage: device found at 2
[ 2.656582]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '002'
[ 2.656654] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 2.656821] usb-storage: waiting for device to settle before scanning
[ 2.708046] ehci_hcd 0000:00:13.5: port 2 full speed --> companion
[ 2.708137] ehci_hcd 0000:00:13.5: GetStatus port 2 status 003801 POWER
OWNER sig=j CONNECT
[ 2.708318] hub 1-0:1.0: port 2 not reset yet, waiting 50ms
[ 2.760038] ehci_hcd 0000:00:13.5: GetStatus port 2 status 003002 POWER
OWNER sig=se0 CSC
[ 2.760224] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 2.760319] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 2.760408] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 2.760494] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 2.760570] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0004
[ 2.760657] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 2.760742] ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] =
0x00010101 CSC PPS CCS
[ 2.760873] hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
[ 2.861139] usb usb2: uevent
[ 2.861175] usb 2-0:1.0: uevent
[ 2.861277] usb usb3: uevent
[ 2.861314] usb 3-0:1.0: uevent
[ 2.861415] usb usb4: uevent
[ 2.861450] usb 4-0:1.0: uevent
[ 2.861549] usb usb5: uevent
[ 2.861583] usb 5-0:1.0: uevent
[ 2.861687] usb usb6: uevent
[ 2.861722] usb 6-0:1.0: uevent
[ 2.861822] usb usb1: uevent
[ 2.861858] usb 1-0:1.0: uevent
[ 2.861897] usb 1-1: uevent
[ 2.861933] usb 1-1:1.0: uevent
[ 2.864048] hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status
0x101
[ 2.885134] ohci_hcd 0000:00:13.0: port[1] reset timeout, stat 00000111
[ 2.936150] ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] =
0x00100103 PRSC PPS PES CCS
[ 2.987064] usb 2-2: new full speed USB device using ohci_hcd and address 2
[ 3.009070] ohci_hcd 0000:00:13.0: port[1] reset timeout, stat 00000113
[ 3.060049] ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] =
0x00100103 PRSC PPS PES CCS
[ 3.130077] usb 2-2: skipped 1 descriptor after interface
[ 3.130082] usb 2-2: skipped 1 descriptor after interface
[ 3.134823] usb 2-2: default language 0x0409
[ 3.140083] usb 2-2: udev 2, busnum 2, minor = 129
[ 3.140164] usb 2-2: New USB device found, idVendor=14dd, idProduct=0002
[ 3.140246] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.140249] usb 2-2: Product: MultiDevice
[ 3.140252] usb 2-2: Manufacturer: Peppercon AG
[ 3.140255] usb 2-2: SerialNumber: 768E1175CA002E778E2336515C01B222
[ 3.140390] usb 2-2: uevent
[ 3.140410] usb 2-2: usb_probe_device
[ 3.140414] usb 2-2: configuration #1 chosen from 1 choice
[ 3.142084] usb 2-2: adding 2-2:1.0 (config #1, interface 0)
[ 3.142125] usb 2-2:1.0: uevent
[ 3.142157] usbhid 2-2:1.0: usb_probe_interface
[ 3.142161] usbhid 2-2:1.0: usb_probe_interface - got id
[ 3.148471] input: Peppercon AG MultiDevice as
/devices/pci0000:00/0000:00:13.0/usb2/2-2/2-2:1.0/input/input3
[ 3.148709] generic-usb 0003:14DD:0002.0001: input,hidraw0: USB HID v1.01
Keyboard [Peppercon AG MultiDevice] on usb-0000:00:13.0-2/input0
[ 3.148875] usb 2-2: adding 2-2:1.1 (config #1, interface 1)
[ 3.148983] usb 2-2:1.1: uevent
[ 3.149011] usbhid 2-2:1.1: usb_probe_interface
[ 3.149116] usbhid 2-2:1.1: usb_probe_interface - got id
[ 3.156179] input: Peppercon AG MultiDevice as
/devices/pci0000:00/0000:00:13.0/usb2/2-2/2-2:1.1/input/input4
[ 3.156442] generic-usb 0003:14DD:0002.0002: input,hidraw1: USB HID v1.01
Mouse [Peppercon AG MultiDevice] on usb-0000:00:13.0-2/input1
[ 3.156600]
/usr/src/xen/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c:
creating file '002'
[ 3.156757] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 3.455023] ohci_hcd 0000:00:13.1: auto-stop root hub
[ 3.455041] ohci_hcd 0000:00:13.2: auto-stop root hub
[ 3.704027] ohci_hcd 0000:00:13.3: auto-stop root hub
[ 3.704043] ohci_hcd 0000:00:13.4: auto-stop root hub
[ 5.181123] md: md1 stopped.
[ 5.192108] md: bind<sdb4>
[ 5.192562] md: bind<sda4>
[ 5.192995] md: bind<sdc4>
[ 5.196365] raid1: raid set md1 active with 3 out of 3 mirrors
[ 5.196482] md1: detected capacity change from 0 to 499586957312
[ 5.198531] md1: unknown partition table
[ 5.705038] hub 4-0:1.0: hub_suspend
[ 5.705127] usb usb4: bus auto-suspend
[ 5.705202] ohci_hcd 0000:00:13.2: suspend root hub
[ 5.705296] hub 5-0:1.0: hub_suspend
[ 5.705373] usb usb5: bus auto-suspend
[ 5.705447] ohci_hcd 0000:00:13.3: suspend root hub
[ 5.705527] hub 6-0:1.0: hub_suspend
[ 5.705604] usb usb6: bus auto-suspend
[ 5.705678] ohci_hcd 0000:00:13.4: suspend root hub
[ 5.706023] hub 3-0:1.0: hub_suspend
[ 5.706101] usb usb3: bus auto-suspend
[ 5.706174] ohci_hcd 0000:00:13.1: suspend root hub
[ 7.657119] scsi 4:0:0:0: Direct-Access USB FLASH DRIVE 34CE
PQ: 0 ANSI: 0 CCS
[ 7.657361] sd 4:0:0:0: Attached scsi generic sg3 type 0
[ 7.658235] sd 4:0:0:0: [sdd] 2015232 512-byte logical blocks: (1.03 GB/984
MiB)
[ 7.659030] usb-storage: device scan complete
[ 7.659462] sd 4:0:0:0: [sdd] Write Protect is off
[ 7.659467] sd 4:0:0:0: [sdd] Mode Sense: 23 00 00 00
[ 7.659471] sd 4:0:0:0: [sdd] Assuming drive cache: write through
[ 7.662974] sd 4:0:0:0: [sdd] Assuming drive cache: write through
[ 7.662980] sdd: sdd1 sdd2 sdd3
[ 7.665259] sd 4:0:0:0: [sdd] Assuming drive cache: write through
[ 7.665263] sd 4:0:0:0: [sdd] Attached SCSI removable disk
[ 12.131313] kjournald starting. Commit interval 5 seconds
[ 12.131332] EXT3-fs: mounted filesystem with writeback data mode.
[ 12.852010] eth0: no IPv6 routers present
[ 13.381651] udevd version 125 started
[ 13.517401] usb usb2: uevent
[ 13.517438] usb 2-0:1.0: uevent
[ 13.517480] usb 2-2: uevent
[ 13.517539] usb 2-2:1.0: uevent
[ 13.517788] usb 2-2:1.1: uevent
[ 13.518236] usb usb3: uevent
[ 13.518273] usb 3-0:1.0: uevent
[ 13.518387] usb usb4: uevent
[ 13.518424] usb 4-0:1.0: uevent
[ 13.518550] usb usb5: uevent
[ 13.518598] usb 5-0:1.0: uevent
[ 13.518730] usb usb6: uevent
[ 13.518767] usb 6-0:1.0: uevent
[ 13.518886] usb usb1: uevent
[ 13.518937] usb 1-0:1.0 __ __ _____ ____ _ _ _
\ \/ /___ _ __ |___ / | ___| _ _ _ __ ___| |_ __ _| |__ | | ___
\ // _ \ \047_ \ |_ \ |___ \ __| | | | \047_ \/ __| __/ _` | \047_ \| |/
_ \
/ \ __/ | | | ___) | ___) |__| |_| | | | \__ \ || (_| | |_) | | __/
/_/\_\___|_| |_| |____(_)____/ \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
(XEN) Xen version 3.5-unstable (root@xxxxxxxxxxxxxxxx) (gcc version 4.3.2
(Debian 4.3.2-1.1) ) Sat Sep 19 12:38:39 CEST 2009
(XEN) Latest ChangeSet: Fri Sep 18 14:45:40 2009 +0100 20228:3a71e070e3c5
(XEN) Command line:
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds
(XEN) EDID info not retrieved because of reasons unknown
(XEN) Disc information:
(XEN) Found 4 MBR signatures
(XEN) Found 4 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009f000 (usable)
(XEN) 000000000009f000 - 00000000000a0000 (reserved)
(XEN) 00000000000f0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000ddee0000 (usable)
(XEN) 00000000ddee0000 - 00000000ddee3000 (ACPI NVS)
(XEN) 00000000ddee3000 - 00000000ddef0000 (ACPI data)
(XEN) 00000000ddef0000 - 00000000ddf00000 (reserved)
(XEN) 00000000e0000000 - 00000000f0000000 (reserved)
(XEN) 00000000fec00000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 0000000220000000 (usable)
(XEN) System RAM: 8158MB (8354300kB)
(XEN) ACPI: RSDP 000F8210, 0024 (r2 ATI )
(XEN) ACPI: XSDT DDEE3100, 0044 (r1 ATI ASUSACPI 42302E31 AWRD 0)
(XEN) ACPI: FACP DDEE8500, 00F4 (r3 ATI ASUSACPI 42302E31 AWRD 0)
(XEN) ACPI: DSDT DDEE3280, 5210 (r1 ATI ASUSACPI 1000 MSFT 3000000)
(XEN) ACPI: FACS DDEE0000, 0040
(XEN) ACPI: HPET DDEE8740, 0038 (r1 ATI ASUSACPI 42302E31 AWRD 98)
(XEN) ACPI: MCFG DDEE87C0, 003C (r1 ATI ASUSACPI 42302E31 AWRD 0)
(XEN) ACPI: APIC DDEE8640, 0084 (r1 ATI ASUSACPI 42302E31 AWRD 0)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-0000000220000000
(XEN) Domain heap initialised
(XEN) found SMP MP-table at 000f6560
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x4008
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[4004,0], pm1x_evt[4000,0]
(XEN) ACPI: wakeup_vec[ddee000c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
(XEN) Processor #0 15:11 APIC version 16
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
(XEN) Processor #1 15:11 APIC version 16
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
(XEN) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
(XEN) ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) ACPI: HPET id: 0x8200 base: 0xfed00000
(XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
(XEN) PCI: MCFG area at e0000000 reserved in E820
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2400.019 MHz processor.
(XEN) CPU0: AMD Flush Filter disabled
(XEN) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
(XEN) CPU: L2 Cache: 512K (64 bytes/line)
(XEN) CPU 0(2) -> Core 0
(XEN) AMD SVM: ASIDs disabled.
(XEN) HVM: SVM enabled
(XEN) CPU0: AMD K8 machine check reporting enabled
(XEN) I/O virtualisation disabled
(XEN) CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 02
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU1: AMD Flush Filter disabled
(XEN) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
(XEN) CPU: L2 Cache: 512K (64 bytes/line)
(XEN) CPU 1(2) -> Core 1
(XEN) AMD: Disabling C1 Clock Ramping Node #0
(XEN) AMD SVM: ASIDs disabled.
(XEN) CPU1: AMD K8 machine check reporting enabled
(XEN) CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 02
(XEN) Total of 2 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 2 CPUs:
(XEN) CPU#0 had -662 usecs TSC skew, fixed it up.
(XEN) CPU#1 had 662 usecs TSC skew, fixed it up.
(XEN) Platform timer is 14.318MHz HPET
(XEN) Brought up 2 CPUs
(XEN) do_IRQ: 1.231 No irq handler for vector (irq -1)
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) HPET: 4 timers in total, 0 timers will be used for broadcast
(XEN) ACPI sleep modes: S3
(XEN) MCA: Use hw thresholding to adjust polling frequency
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80200000 memsz=0x26a870
(XEN) elf_parse_binary: phdr: paddr=0xffffffff8046b000 memsz=0x868e8
(XEN) elf_parse_binary: phdr: paddr=0xffffffff804f2000 memsz=0xc08
(XEN) elf_parse_binary: phdr: paddr=0xffffffff804f4000 memsz=0xccc1c
(XEN) elf_parse_binary: memory: 0xffffffff80200000 -> 0xffffffff805c0c1c
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0xffffffff80000000
(XEN) elf_xen_parse_note: ENTRY = 0xffffffff80200000
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80206000
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: FEATURES =
"writable_page_tables|writable_descriptor_tables|auto_translated_physmap|pae_pgdir_above_4gb|supervisor_mode_kernel"
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_addr_calc_check: addresses:
(XEN) virt_base = 0xffffffff80000000
(XEN) elf_paddr_offset = 0xffffffff80000000
(XEN) virt_offset = 0x0
(XEN) virt_kstart = 0xffffffff80200000
(XEN) virt_kend = 0xffffffff805c0c1c
(XEN) virt_entry = 0xffffffff80200000
(XEN) p2m_base = 0xffffffffffffffff
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, lsb, paddr 0xffffffff80200000 -> 0xffffffff805c0c1c
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000214000000->0000000218000000 (2014025 pages to be
allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff80200000->ffffffff805c0c1c
(XEN) Init. ramdisk: ffffffff805c1000->ffffffff817ec800
(XEN) Phys-Mach map: ffffffff817ed000->ffffffff8276aa48
(XEN) Start info: ffffffff8276b000->ffffffff8276b4b4
(XEN) Page tables: ffffffff8276c000->ffffffff82785000
(XEN) Boot stack: ffffffff82785000->ffffffff82786000
(XEN) TOTAL: ffffffff80000000->ffffffff82c00000
(XEN) ENTRY ADDRESS: ffffffff80200000
(XEN) Dom0 has maximum 2 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 -> 0xffffffff8046a870
(XEN) elf_load_binary: phdr 1 at 0xffffffff8046b000 -> 0xffffffff804f18e8
(XEN) elf_load_binary: phdr 2 at 0xffffffff804f2000 -> 0xffffffff804f2c08
(XEN) elf_load_binary: phdr 3 at 0xffffffff804f4000 -> 0xffffffff8052dff8
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three times to switch input
to Xen)
(XEN) Freed 140kB init memory.
(XEN) io_apic.c:2206:
(XEN) ioapic_guest_write: apic=0, pin=2, irq=0
(XEN) ioapic_guest_write: new_entry=00000900
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) PCI add device 00:14.1
(XEN) Set CPU acpi_id(0) cpuid(0) Px State info:
(XEN) _PPC: 0
(XEN) Set CPU acpi_id(1) cpuid(1) Px State info:
(XEN) _PPC: 0
(XEN) no cpu_id for acpi_id 2
(XEN) no cpu_id for acpi_id 3
(XEN) PCI add device 00:13.0
(XEN) allocated vector for irq:16
(XEN) PCI add device 00:13.1
(XEN) allocated vector for irq:17
(XEN) PCI add device 00:13.2
(XEN) allocated vector for irq:18
(XEN) PCI add device 00:13.3
(XEN) PCI add device 00:13.4
(XEN) PCI add device 00:13.5
(XEN) allocated vector for irq:19
(XEN) PCI add device 00:14.1
(XEN) PCI add device 02:00.0
(XEN) PCI add device 00:12.0
(XEN) allocated vector for irq:22
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home