On Fri, 2009-05-29 at 09:31 -0400, Adam Wead wrote:
> On May 28, 2009, at 9:16 PM, Fajar A. Nugraha wrote:
>
> > On Fri, May 29, 2009 at 3:55 AM, Mike Brady
> > <mike.brady@xxxxxxxxxxxxxx> wrote:
> >>
> >> That would be because both Xen and RHEL/Centos are broken when it
> >> comes
> >> to bonded bridged interfaces.
> >
> >> Apply the patch from https://bugzilla.redhat.com/show_bug.cgi?
> >> id=463014
> >
> > Thanks for the info. I have a similar setup, but strangely enough it
> > works without any need for patch.
> > Perhaps its because I'm using bridging on top of vlan on top of
> > bonding.
> >
>
> Mine works as well too, under Red Hat EL5, but I don't use any config
> file under sysconfig to create the bridge or any vlan either. This
> may be why this bug didn't' affect me. Instead I have Red Hat only
> create the bond device from the 2 interfaces, and have Xen create the
> bridge:
>
> /etc/sysconfig/network-scripts/ifcfg-eth0
> DEVICE=eth0
> TYPE=Ethernet
> USERCTL=no
> ONBOOT=yes
> BOOTPROTO=none
> IPV6INIT=no
> PEERDNS=no
> HWADDR=00:1A:64:09:26:F4
> MASTER=bond0
> SLAVE=yes
>
> /etc/sysconfig/network-scripts/ifcfg-eth1
> DEVICE=eth1
> TYPE=Ethernet
> USERCTL=no
> ONBOOT=yes
> BOOTPROTO=none
> IPV6INIT=no
> PEERDNS=no
> HWADDR=00:1A:64:09:26:F6
> MASTER=bond0
> SLAVE=yes
>
> /etc/sysconfig/network-scripts/ifcfg-bond0
> DEVICE=bond0
> BOOTPROTO=none
> ONBOOT=yes
> USERCTL=no
> IPV6INIT=no
> PEERDNS=no
> IPADDR=10.79.184.5
> NETMASK=255.255.255.0
> GATEWAY=10.79.184.254
>
> Putting the following options under /etc/modprobe.conf takes care of
> the rest:
> alias bond0 bonding
> options bonding miimon=100 mode=0
>
> Then, Xen creates the bridge to bond0 under /etc/xen/xend.cfg
> (network-script 'network-bridge netdev=bond0')
>
> and then creates pbond0, and xenbr0
>
> The only problem I'm having with this setup is that I can apparently
> only attach one guest to xenbr0. If I attach a second, it's network
> connectivity is unstable and it's inaccessible over the network.
> However, the setup works great for one guest: you can unplug either
> NIC and the network stays up.
>
> There is a network-bridge-bonding script under /etc/xen/scripts that
> would seem to address everyone's needs. I tried to use it under
> xend.cfg:
> (network-script 'network-bridge-bonding netdev=bond0')
>
> But could never get it to work...
>
> I'd like to find out to attach multiple guests to a bonded device,
> but don't have an extra multi-NIC system handy to play with. I'd
> appreciate hearing you all's views on this.
>
> best,
>
> ...adam
>
>
>
Which Xen and therefore network-bridge script are you running?
Your configuration will work with Red Hat's network-bridge script. The
default Xen script takes the interface down (in this case bond0) when
it is moving the addresses etc around, which breaks the bond. The Red
Hat network-bridge script doesn't take the interface down if is a
bond. I was doing things the way you are when I was using the Red Hat
Xen packages. When I moved to the gitco packages (which has the
standard Xen network-bridge script) I changed to what I have previously
indicated.
I currently only have 3 DomUs using the bridge, but have had more in
the past with no networking issues.
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home