I had a similar issue with one of my Centos 5.1 servers, which was fixed by
running the command:
ethtool -K eth0 tx off
I added this to my rc.local file of each DomU.
Hope it works for you.
Steve
________________________________________
From: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
[xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of s@l
[sal.bayat@xxxxxxxxxxxxxxxx]
Sent: Friday, July 18, 2008 3:50 PM
To: xen-users@xxxxxxxxxxxxxxxxxxx
Subject: [Xen-users] Xen Installation without virtualization enabled in Bios
Hi there,
Having a problem with Xen using RHEL 5. Using a dell poweredge 1950 with
BCM5708 integrated NIC's.
07:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708
Gigabit Ethernet (rev 12)
Subsystem: Dell Unknown device 01b3
Control: I/O- Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f4000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=8
Status: Dev=07:00.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 214082b132d03000 Data: 0b40
Basically, I have this strange issue where everything is good, I can create
my virtual guests, but there is some issue with network connectivity. I can
get to the outside world no problem from the virtual host, but on the
guests, I can only ping the local machine, I cant ping or access anything on
the outside world.
At first I was taking a look at drivers and other network related problems,
when I noticed that the virtualization option in the bios cpu settings was
NOT enabled. I enabled it, but im still having the same problem.
My question is: Would installing RHEL 5 and Xen while this option was NOT
enabled in the bios cause problems and perhaps cause this networking
connectivity issue im experiencing? Do I need to reinstall xen?
Info:
version: xen-3.0.3-64.el5_2.1
--
View this message in context:
http://www.nabble.com/Xen-Installation-without-virtualization-enabled-in-Bios-tp18532312p18532312.html
Sent from the Xen - User mailing list archive at Nabble.com.
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home