Why not have a short look to Novells article?
http://www.novell.com/coolsolutions/feature/17605.html
It works perfectly for me.
Am 10.03.2007 18:59 Uhr schrieb "Mark Williamson" unter
<mark.williamson@xxxxxxxxxxxx>:
>> I have a machine with two different nics (sis900 and dmfe).
>> I am trying bonding in Xen. (on FC6, intel x386, para virtualization).
>>
>> In the past I did successfully configured and used bonding on non-Xen
>> Linux machines.
>>
>> I saw some posts in this list and in other sites regarding Xen
>> bonding, but I am a little bewildered
>> so I want to verify something:
>>
>> I am using the default /etc/xen/xend-config.sxp config file, which
>> means I am using
>> bridging (ifconfig can show xenbr0).
>>
>> When booting into domain 0 both nics are recognized (as I can see from
>> dmesg), also "ifconfig -a" from dom0 shows eth0 and eth1.
>
> The default config bridges eth0, so you'll need to tweak things a bit to get
> both eth0 and eth1 working as a bonding device on that bridge...
>
>> Now when I boot into domain U , "ifconfig -a" shows only eth0.
>> /etc/modprobe.conf has a line saying "alias eth0 xennet" (but eth1
>> does not appear in /etc/modprobe.conf).
>
> That's fine - domUs just see a virtual ethernet device. There's probably not
> much point in exposing the two real ethernet devices to guests. If you
> configure bonding in dom0 you should be able to hide this detail completely
> from the guests - they'll just see their virtual network going faster.
>
>> Now I have two questions:
>> 1)I want to configure bonding through the initscripts
>> (namely , create /etc/sysconfig/network-scripts/ifcfg-bond0 and add
>> MASTER/SLAVE entries in /etc/sysconfig/network-scripts/ifcfg-eth0 and
>> /etc/sysconfig/network-scripts/ifcfg-eth1 ,
>> etc.) Where should I do it ? In dom 0 ? or in dom U ? I saw somewhere
>> in xen-user mailing list that it should be done in dom U ; but as I
>> said, ifconfig -a does not show eth1 in dom U .
>> Any tips or guidance as to what should I do or pointers to bonding on
>> Xen that worked for you will be helpful.
>
> If you edit the config you could pass it through, but I think it would be
> better to try and do it in dom0 so that the guests don't need to be configured
> individually.
>
>>
>> 2)
>> After boot of domain U , I ran ifconfig -a ***in domain 0***, and I
>> saw only ONE vif1.* instance (vif1.0) I expected to see also vif1.1
>> for the second nic.
>> The XenNetworking wiki page says : "If you create multiple network
>> interfaces for a domU, it's ends will be eth0, eth1, etc, whereas the
>> dom0 end will be vif<id#>.0, vif<id#>.1, etc."
>> (http://wiki.xensource.com/xenwiki/XenNetworking). Did I misunderstood
>> something ?
>> Am I wrong somewhere?
>
> Unless you explicitly specified two virtual network interfaces in the domain's
> config, you won't get two appearing there. This is probably fine for you;
>
> I'd be inclined to try bonding eth0 and eth1 in the normal way in dom0 then
> arranging for the bonding device to be added to the bridge instead of either
> eth0 or eth1... I'm not sure if there would be any nasty interactions with
> the bridging and bonding code here. If you have any problems, you could also
> try using a routed rather than bridged setup.
>
> Solutions to this will probably involve some fiddling with the dom0 config
> and / or the networking setup scripts used to configure vifs.
>
> Hope this clears up some things for you!
>
> Cheers,
> Mark
>
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home