Ok, then we can narrow down the issue to Powernow driver. CC Mark who is the
author of Powernow.
Regards
Ke
-----Original Message-----
From: Sander Eikelenboom [mailto:linux@xxxxxxxxxxxxxx]
Sent: Saturday, January 09, 2010 1:24 AM
To: Yu, Ke
Cc: xen-devel@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-devel] [xen 3.4.2][2.6.31.6-pvops] Problems with cpufreq=xen
power management on amd k8 cpu
Hello Ke,
With xen-3.4.2 with your patch and 2.6.31.6-pvops it returns
But when i look at the current linux kernels powernow-k8.c your check isn't
valid for family 15 (CPUID_XFAM_K8) but only for CPUID_XFAM_10H cpu's.
I have a family 15 cpu.
I don't know what this means for the rest of the code in de powernow-k8 version
in xen. Should it support the family 15 cpu's ?
Regards,
Sander
static void check_supported_cpu(void *_rc)
512 {
513 u32 eax, ebx, ecx, edx;
514 int *rc = _rc;
515
516 *rc = -ENODEV;
517
518 if (current_cpu_data.x86_vendor != X86_VENDOR_AMD)
519 return;
520
521 eax = cpuid_eax(CPUID_PROCESSOR_SIGNATURE);
522 if (((eax & CPUID_XFAM) != CPUID_XFAM_K8) &&
523 ((eax & CPUID_XFAM) < CPUID_XFAM_10H))
524 return;
525
526 if ((eax & CPUID_XFAM) == CPUID_XFAM_K8) {
527 if (((eax & CPUID_USE_XFAM_XMOD) != CPUID_USE_XFAM_XMOD) ||
528 ((eax & CPUID_XMOD) > CPUID_XMOD_REV_MASK)) {
529 printk(KERN_INFO PFX
530 "Processor cpuid %x not supported\n", eax);
531 return;
532 }
533
534 eax = cpuid_eax(CPUID_GET_MAX_CAPABILITIES);
535 if (eax < CPUID_FREQ_VOLT_CAPABILITIES) {
536 printk(KERN_INFO PFX
537 "No frequency change capabilities
detected\n");
538 return;
539 }
540
541 cpuid(CPUID_FREQ_VOLT_CAPABILITIES, &eax, &ebx, &ecx, &edx);
542 if ((edx & P_STATE_TRANSITION_CAPABLE)
543 != P_STATE_TRANSITION_CAPABLE) {
544 printk(KERN_INFO PFX
545 "Power state transitions not supported\n");
546 return;
547 }
548 } else { /* must be a HW Pstate capable processor */
549 cpuid(CPUID_FREQ_VOLT_CAPABILITIES, &eax, &ebx, &ecx, &edx);
550 if ((edx & USE_HW_PSTATE) == USE_HW_PSTATE)
551 cpu_family = CPU_HW_PSTATE;
552 else
553 return;
554 }
555
556 *rc = 0;
557 }
Friday, January 8, 2010, 3:32:18 PM, you wrote:
> Hi Sander,
> For option1 "cpufreq=dom0-kernel", it is not working currently, the reason is
> a bit complex, and let me explain. For every processor, there is
> corresponding acpi processor object in ACPI DSDT table. Kernel use struct
> acpi_processor to represent the acpi processor object. There is a field "id"
> in acpi_processor representing the cpu id (the same id as
> smp_processor_id()). Kernel cpufreq use acpi_processor->id to do the
> frequency scaling. Unfortunately, in pv_ops domain0, the acpi_processor->id
> value is not correct, because it is get by acpi_id->apic_id->id mapping, and
> in pv_ops dom0, the apic_id of vcpu is not correctly initialized. Please see
> drivers/acpi/processor_core.c:get_cpu_id() for detail code, where
> cpu_physical_id() is not initialized in pv_ops dom0 case. I am still thinking
> if there is better approach to do the acpi_id->apic_id->id mapping in pv_ops
> dom0 case.
> BTW, "cpufreq=dom0-kernel" is not recommend, due to that it require
> #pCPU=#vCPU, and all vCPU in dom0 must be pined.
> For option2 "cpufreq=xen", from the log, Xen can get all the P states info,
> but it failed to do cpufreq cpu initialization
> (xen/arch/x86/acpi/cpufreq/cpufreq.c: cpufreq_cpu_init()), so the cpufreq is
> not started finally, and xenpm cannot set cpufreq parameter. To get more
> debug info, I write a simple patch as attached, could you please have a try
> and send the debug info?
> Another thing is, does "cpufreq=xen" work with linux-2.6.18-xen dom0?
> Best Regards
> Ke
> -----Original Message-----
> From: xen-devel-bounces@xxxxxxxxxxxxxxxxxxx
> [mailto:xen-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Sander Eikelenboom
> Sent: Thursday, January 07, 2010 11:08 PM
> To: xen-devel@xxxxxxxxxxxxxxxxxxx
> Subject: [Xen-devel] [xen 3.4.2][2.6.31.6-pvops] Problems with cpufreq=xen
> power management on amd k8 cpu
> Hi All,
> I'm trying to get powermanagement working with xen and a 2.6.31.6-pvops
> kernel on xen 3.4.2
> From what I have read, I have 2 options:
> 1) Let the xen hypervisor do the powermanagement (cpufreq=xen)
> 2) Let the dom0 kernel do the powermanagement (cpufreq=dom0-kernel)
> When booting the 2.6.31.6-pvops kernel on bare metal without hypervisor the
> powernow-k8 module works.
> When booting the 2.6.31.6-pvops kernel as dom0 on the xen 3.4.2 hypervisor
> the powernow-k8 module doesn't load and complains:
> Jan 7 15:25:37 localhost kernel: [ 12.797914] powernow-k8: Found 1
> AMD Athlon(tm) Dual Core Processor 4850e processors (2 cpu cores) (version
> 2.20.00)
> Jan 7 15:25:37 localhost kernel: [ 12.797926] powernow-k8: register
> performance failed: bad ACPI data
> Jan 7 15:25:37 localhost kernel: [ 12.797929] [Firmware Bug]:
> powernow-k8: No compatible ACPI _PSS objects found.
> Jan 7 15:25:37 localhost kernel: [ 12.797931] [Firmware Bug]:
> powernow-k8: Try again with latest BIOS.
> Jan 7 15:25:37 localhost kernel: [ 12.797941] powernow-k8: register
> performance failed: bad ACPI data
> Jan 7 15:25:37 localhost kernel: [ 12.822315] acpi-cpufreq:
> acpi_cpufreq_init
> Jan 7 15:25:37 localhost kernel: [ 12.822319] acpi-cpufreq:
> acpi_cpufreq_early_init
> Jan 7 15:25:37 localhost kernel: [ 12.822333] acpi-cpufreq:
> acpi_cpufreq_cpu_init
> Jan 7 15:25:37 localhost kernel: [ 12.822338] acpi-cpufreq:
> acpi_cpufreq_cpu_init
> It could be that additional changes are needed to the pvops kernel that have
> been made to the xen 2.6.18.8 kernel ?
> When trying the first option, and let the hypervisor do the powermanagement
> (booting with cpufreq=xen cpufreq.debug=2 loglvl=all)
> it shows the following in xm dmesg (complete xm dmesg attachted):
> (XEN) Set CPU acpi_id(0) cpuid(0) Px State info:
> (XEN) _PPC: 0
> (XEN) Set CPU acpi_id(0) cpuid(0) Px State info:
> (XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=0,
> bit_offset=0, reserved=0, address=0
> (XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=0,
> bit_offset=0, reserved=0, address=0
> (XEN) _PSS: state_count=6
> (XEN) State0: 2500MHz 50000mW 100us 9us 0xe8201391 0x391
> (XEN) State1: 2400MHz 46020mW 100us 9us 0xe82013d0 0x3d0
> (XEN) State2: 2200MHz 38671mW 100us 9us 0xe820144e 0x44e
> (XEN) State3: 2000MHz 32100mW 100us 9us 0xe82014cc 0x4cc
> (XEN) State4: 1800MHz 26265mW 100us 9us 0xe820154a 0x54a
> (XEN) State5: 1000MHz 13888mW 100us 9us 0xe8201582 0x582
> (XEN) _PSD: num_entries=5 rev=0 domain=0 coord_type=253 num_processors=2
> (XEN) _PPC: 0
> (XEN) Set CPU acpi_id(1) cpuid(1) Px State info:
> (XEN) _PPC: 0
> (XEN) Set CPU acpi_id(1) cpuid(1) Px State info:
> (XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=0,
> bit_offset=0, reserved=0, address=0
> (XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=0,
> bit_offset=0, reserved=0, address=0
> (XEN) _PSS: state_count=6
> (XEN) State0: 2500MHz 50000mW 100us 9us 0xe8201391 0x391
> (XEN) State1: 2400MHz 46020mW 100us 9us 0xe82013d0 0x3d0
> (XEN) State2: 2200MHz 38671mW 100us 9us 0xe820144e 0x44e
> (XEN) State3: 2000MHz 32100mW 100us 9us 0xe82014cc 0x4cc
> (XEN) State4: 1800MHz 26265mW 100us 9us 0xe820154a 0x54a
> (XEN) State5: 1000MHz 13888mW 100us 9us 0xe8201582 0x582
> (XEN) _PSD: num_entries=5 rev=0 domain=0 coord_type=253 num_processors=2
> (XEN) _PPC: 0
> So it seems to find all available powerstates, but using xenpm doesn't seem
> to work:
> serveerstertje:~# xenpm get-cpu-topology
> CPU core socket
> CPU0 0 0
> CPU1 1 0
> serveerstertje:~# xenpm set-scaling-governor userspace
> [CPU0] failed to set governor name
> [CPU1] failed to set governor name
> serveerstertje:~# xenpm set-scaling-governor ondemand
> [CPU0] failed to set governor name
> [CPU1] failed to set governor name
> serveerstertje:~# xenpm set-scaling-governor performance
> [CPU0] failed to set governor name
> [CPU1] failed to set governor name
> serveerstertje:~# xenpm set-scaling-governor powersave
> [CPU0] failed to set governor name
> [CPU1] failed to set governor name
> serveerstertje:~# xenpm get-cpufreq-para
> [CPU0] failed to get cpufreq parameter
> [CPU1] failed to get cpufreq parameter
--
Best regards,
Sander mailto:linux@xxxxxxxxxxxxxx
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home