Dexuan,
Could you give me some pointers about the right implementation of
FLR/PCIe reset on pciback driver? I am looking into it now and would
like to get it done.
Thanks,
Neo
On Thu, Sep 18, 2008 at 11:45 PM, Neo Jia <neojia@xxxxxxxxx> wrote:
> Dexuan,
>
> May I know the current development stage of FLR in pciback driver?
>
> Thanks,
> Neo
>
> On Thu, Jul 24, 2008 at 3:19 AM, Cui, Dexuan <dexuan.cui@xxxxxxxxx> wrote:
>> Yuji Shimada wrote:
>>>> Yuji Shimada wrote:
>>>>> On Wed, 23 Jul 2008 11:16:31 +0800
>>>>> "Cui, Dexuan" <dexuan.cui@xxxxxxxxx> wrote:
>>>>>> I think xenstore seems to be a little ugly place to remember the
>>>>>> proper values of all or part of registers of all the devices in
>>>>>> the system. I agree pciback is a good place.
>>>>>> Yes. Now I realize pciback seems to be the best place to do most of
>>>>>> the FLR logic. But this needs modify pciback and add interfaces for
>>>>>> Control Panel. I'm not sure the changes can be small enought to be
>>>>>> in 3.3.
>>>>>
>>>>> Hi Cui,
>>>>>
>>>>> What do you think about the following idea?
>>>>> - For 3.3, modify xend to have limited saving/restoring and
>>>>> resetting functions.
>>>>> - For 3.4, modify pciback to have proper saving/restoring and
>>>>> resetting functions.
>>>> Hi Yuji,
>>>> Thanks very much for the suggestions!
>>>> I agree.
>>>>
>>>>> The purpose of saving is to save the values configured by firmware.
>>>>> So the best timing of saving the value is when dom0 starts. But if
>>>>> saving the values when dom0 starts, pciback is the best place to
>>>>> save/restore. If pciback saves/restores the values, we need many
>>>>> codings. So it is difficult to achieve it in 3.3.
>>>>>
>>>>> So for 3.3, there is a way that saving the value just before
>>>>> resetting. It is possible xend saves/restores the value, I think. In
>>>>
>>>> In current code of xend,
>>>> The steps are:
>>>> 1) save the current values of the configuration space registers 2)
>>>> do_FLR 3) restore the values of the registers
>>>>
>>>> "a way that saving the value just before resetting." -- do you mean
>>>> the same thing?
>>>>
>>>
>>> Hi Cui,
>>>
>>> Yes, I mean the same thing. But in current code of xend, xend saves
>>> all Configuration Registers. The only registers I suggested before
>>> should be saved. Small modification is needed.
>>
>> It sounds good. Namely, we need to save/restore the following registers
>> for now:
>>
>> - Base Address Registers
>> - Cache-line size Register
>> - Latency timer Register
>> - Enable SERR Bit/Enable PERR Bit in Device Control Register
>> - Uncorrectable Error Mask Register
>> - Uncorrectable Error Severity Register
>> - Correctable Error Mask Register
>> - Advanced Error Capabilities and Control Register
>> - Device Control Register
>> - Link Control Register
>> - Secondary Uncorrectable Error Severity Register
>> - Secondary Uncorrectable Error Mask Register
>> - Device Control 2 Register
>> - Link Control 2 Register
>> - The following resister should be configured to "0".
>> - PME Enable Bit/PME Status Bit in PCI Power Management
>> Control/Status Register
>>
>> However, I think maybe the modification is not small enough because
>> 1) we need to save each registers one by one using Python script in
>> xend, and later restore each registers respectively one by one;
>> 2) we should handle bridge in some cases, so we need to distinguish
>> bridges from regular devices since the register layouts are different;
>> 3) Some of the registers you listed are inside the extended PCIe space,
>> so we need detect if a device/bride has the PCIe capability? And find
>> each capability/save the register;
>> 4) xend uses the sys filesystem to access the registers. For the case of
>> PCIe registers, when Dom0 is configured with/without PCIe support (by
>> default, it's "without" now), we should detect and treat it differently?
>>
>> Acutually looks the save/restore-all-the-256-byte idea (which was in
>> hypervisor and is in xend now) works very well for quite a long time,
>> and no actual issue is reported as far as I know. Since it looks very
>> difficult to do things perfectly for now and we'll improve them by
>> changing pciback in the long run, maybe keeping the current simple
>> method is acceptable? :-)
>>
>> Thanks,
>> -- Dexuan
>>>
>>>>> this case, xend don't need saving the values in xenstore. Because
>>>>> interval between saving and restoring is small.
>>>>>
>>>>> My idea is summarized as follows:
>>>>>
>>>>> Xen Timing Where Difficulty
>>>>> 3.3 before resetting xend easy
>>>>> 3.4 when Dom0 starts pciback hard
>>>>>
>>>> I exactly agree with you.
>>>>
>>>
>>> Thanks.
>>
>>
>>
>>
>> _______________________________________________
>> Xen-devel mailing list
>> Xen-devel@xxxxxxxxxxxxxxxxxxx
>> http://lists.xensource.com/xen-devel
>>
>
>
>
> --
> I would remember that if researchers were not ambitious
> probably today we haven't the technology we are using!
>
--
I would remember that if researchers were not ambitious
probably today we haven't the technology we are using!
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home