Hi Neo,
Sorry, for now I have no update for it. We're focusing on fixing some important
bugs since xen 3.3.1 is coming...
Thanks,
-- Dexuan
-----Original Message-----
From: Neo Jia [mailto:neojia@xxxxxxxxx]
Sent: 2008年9月19日 14:46
To: Cui, Dexuan
Cc: Yuji Shimada; xen-devel@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-devel] [PATCH] Improve the current FLR logic
Dexuan,
May I know the current development stage of FLR in pciback driver?
Thanks,
Neo
On Thu, Jul 24, 2008 at 3:19 AM, Cui, Dexuan <dexuan.cui@xxxxxxxxx> wrote:
> Yuji Shimada wrote:
>>> Yuji Shimada wrote:
>>>> On Wed, 23 Jul 2008 11:16:31 +0800
>>>> "Cui, Dexuan" <dexuan.cui@xxxxxxxxx> wrote:
>>>>> I think xenstore seems to be a little ugly place to remember the
>>>>> proper values of all or part of registers of all the devices in
>>>>> the system. I agree pciback is a good place.
>>>>> Yes. Now I realize pciback seems to be the best place to do most of
>>>>> the FLR logic. But this needs modify pciback and add interfaces for
>>>>> Control Panel. I'm not sure the changes can be small enought to be
>>>>> in 3.3.
>>>>
>>>> Hi Cui,
>>>>
>>>> What do you think about the following idea?
>>>> - For 3.3, modify xend to have limited saving/restoring and
>>>> resetting functions.
>>>> - For 3.4, modify pciback to have proper saving/restoring and
>>>> resetting functions.
>>> Hi Yuji,
>>> Thanks very much for the suggestions!
>>> I agree.
>>>
>>>> The purpose of saving is to save the values configured by firmware.
>>>> So the best timing of saving the value is when dom0 starts. But if
>>>> saving the values when dom0 starts, pciback is the best place to
>>>> save/restore. If pciback saves/restores the values, we need many
>>>> codings. So it is difficult to achieve it in 3.3.
>>>>
>>>> So for 3.3, there is a way that saving the value just before
>>>> resetting. It is possible xend saves/restores the value, I think. In
>>>
>>> In current code of xend,
>>> The steps are:
>>> 1) save the current values of the configuration space registers 2)
>>> do_FLR 3) restore the values of the registers
>>>
>>> "a way that saving the value just before resetting." -- do you mean
>>> the same thing?
>>>
>>
>> Hi Cui,
>>
>> Yes, I mean the same thing. But in current code of xend, xend saves
>> all Configuration Registers. The only registers I suggested before
>> should be saved. Small modification is needed.
>
> It sounds good. Namely, we need to save/restore the following registers
> for now:
>
> - Base Address Registers
> - Cache-line size Register
> - Latency timer Register
> - Enable SERR Bit/Enable PERR Bit in Device Control Register
> - Uncorrectable Error Mask Register
> - Uncorrectable Error Severity Register
> - Correctable Error Mask Register
> - Advanced Error Capabilities and Control Register
> - Device Control Register
> - Link Control Register
> - Secondary Uncorrectable Error Severity Register
> - Secondary Uncorrectable Error Mask Register
> - Device Control 2 Register
> - Link Control 2 Register
> - The following resister should be configured to "0".
> - PME Enable Bit/PME Status Bit in PCI Power Management
> Control/Status Register
>
> However, I think maybe the modification is not small enough because
> 1) we need to save each registers one by one using Python script in
> xend, and later restore each registers respectively one by one;
> 2) we should handle bridge in some cases, so we need to distinguish
> bridges from regular devices since the register layouts are different;
> 3) Some of the registers you listed are inside the extended PCIe space,
> so we need detect if a device/bride has the PCIe capability? And find
> each capability/save the register;
> 4) xend uses the sys filesystem to access the registers. For the case of
> PCIe registers, when Dom0 is configured with/without PCIe support (by
> default, it's "without" now), we should detect and treat it differently?
>
> Acutually looks the save/restore-all-the-256-byte idea (which was in
> hypervisor and is in xend now) works very well for quite a long time,
> and no actual issue is reported as far as I know. Since it looks very
> difficult to do things perfectly for now and we'll improve them by
> changing pciback in the long run, maybe keeping the current simple
> method is acceptable? :-)
>
> Thanks,
> -- Dexuan
>>
>>>> this case, xend don't need saving the values in xenstore. Because
>>>> interval between saving and restoring is small.
>>>>
>>>> My idea is summarized as follows:
>>>>
>>>> Xen Timing Where Difficulty
>>>> 3.3 before resetting xend easy
>>>> 3.4 when Dom0 starts pciback hard
>>>>
>>> I exactly agree with you.
>>>
>>
>> Thanks.
>
>
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home