WARNING - OLD ARCHIVES

This is an archived copy of the Xen.org mailing list, which we have preserved to ensure that existing links to archives are not broken. The live archive, which contains the latest emails, can be found at http://lists.xen.org/
   
 
 
Xen 
 
Home Products Support Community News
 
   
 

xen-users

Re: [Xen-users] centos 5.6 upgrade to 4.1 - no DomUs listed

To: xen-users@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-users] centos 5.6 upgrade to 4.1 - no DomUs listed
From: Andy Howell <AndyHowell@xxxxxxxxxxxxx>
Date: Wed, 18 May 2011 05:52:27 -0500
Delivery-date: Wed, 18 May 2011 03:53:41 -0700
Envelope-to: www-data@xxxxxxxxxxxxxxxxxxx
In-reply-to: <4DD3848D.30606@xxxxxxxxxxxxxxxxxxxxx>
List-help: <mailto:xen-users-request@lists.xensource.com?subject=help>
List-id: Xen user discussion <xen-users.lists.xensource.com>
List-post: <mailto:xen-users@lists.xensource.com>
List-subscribe: <http://lists.xensource.com/mailman/listinfo/xen-users>, <mailto:xen-users-request@lists.xensource.com?subject=subscribe>
List-unsubscribe: <http://lists.xensource.com/mailman/listinfo/xen-users>, <mailto:xen-users-request@lists.xensource.com?subject=unsubscribe>
References: <4DD2C00A.2070307@xxxxxxxxxxxxx> <BANLkTimzPi+-AgCQLYG3oQDAK7y1ufuBag@xxxxxxxxxxxxxx> <4DD2EF66.3060304@xxxxxxxxxxxxx> <BANLkTik1S2njvxwdNXw3u3-0q-_jeC6ByQ@xxxxxxxxxxxxxx> <4DD3749B.9060205@xxxxxxxxxxxxx> <4DD3848D.30606@xxxxxxxxxxxxxxxxxxxxx>
Sender: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
User-agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.2.17) Gecko/20110424 Lightning/1.0b2 Thunderbird/3.1.10
On 05/18/2011 03:34 AM, Randy Katz wrote:
> try booting with pci=nomsi on the kernel line,
> If you setup networking according to this then things should be working, and 
> no need to
> use vif in the bridge line: 
> http://wiki.xensource.com/xenwiki/HostConfiguration/Networking
> 
> One of my working confs looks like this (CentOS 5.6 Xen 4.1):
> 
> name = "test1"
> memory = "512"
> disk = [ "phy:/dev/vg1/test1,xvda,w" ]
> vif = [ 'mac=00:16:3e:aa:aa:91,bridge=xenbr0' ]
> vcpus=1
> on_reboot = 'restart'
> on_crash = 'restart'
> bootloader = "/usr/bin/pygrub"
> 
> on node:
> # netstat -rn
> Kernel IP routing table
> Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
> 192.168.0.0      0.0.0.0         255.255.255.0   U         0 0          0 
> xenbr0
> 169.254.0.0     0.0.0.0         255.255.0.0     U         0 0          0 
> xenbr0
> 0.0.0.0         192.168.1.1      0.0.0.0         UG        0 0          0 
> xenbr0
> 

Randy,

        Thanks! pci-nomsi enabled me to boot. I'm able to get a domu up and 
login via vncviewer.
Networking isn't working however. I created xenbr0 with no IP address, as it was
previously. Something isn't correct. I don't see the interfaces that were part 
of the
bridge before:

   tap0
   vif1.0
   peth0
   vif0.0

I vaguely remember the xen scripts created those. I'll have to read up on it 
after a bit
of sleep. Thanks again.

Andy


/etc/sysconfig/network-scripts/ifcfg-xenbr0
DEVICE=xenbr0
TYPE=Bridge
BOOTPROTO=none
ONBOOT=yes
DELAY=0
NM_CONTROLLED=no

/etc/sysconfig/network-scripts/ifcfg-eth0
# Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet 
controller
DEVICE=eth0
BOOTPROTO=static
HWADDR=E0:CB:4E:97:68:DD
IPADDR=172.16.1.8
NETMASK=255.255.0.0
ONBOOT=yes
#BRIDGE=xenbr0


_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users