Hi,
What
do You think about the using the second possibility of NIC hardware for DomU –
the NE2000 compatible card/driver? Maybe this will work... You must just define
Your virtual network interface in your DomU configuration file with the „model“
switch similary to the line
vif
= [ 'type=ioemu, mac=00:16:3e:00:00:11, bridge=xenbr0, model=ne2k_pci' ]
And
this should bring the different HW to Windows guest – and NE2000
compatible cards could/should be supported more than the realtec...
Good
luck, Archie.
From: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Makoto
Sakurai
Sent: Thursday, April 26, 2007 6:04 PM
To: 'Nakajima, Jun'; xen-users@xxxxxxxxxxxxxxxxxxx
Cc: 'Makoto Sakurai'
Subject: RE: [Xen-users] Network configuration error in Windows
VistaBusinessHVM / Xen 3.04
Hi Jun,
Sorry for the late reply. I tried to
copy the Realtek driver from the Windows 2003 / Xen HVM. However, it did not
work. It is because the version of the Realtek driver installed in Windows 2003
Server was older than that of Windows Vista Business. Moreover, I could not
find out which files / directories are appropriate for the whole copying from
Win2003 to WinVista. I just copied RTL8139.sys from
c:\Windows\System32/drivers.
Is there any advice for me?
Makoto Sakurai
From: Nakajima, Jun
[mailto:jun.nakajima@xxxxxxxxx]
Sent: Monday, April 09, 2007 11:40 PM
To: Makoto Sakurai; xen-users@xxxxxxxxxxxxxxxxxxx
Subject: RE: [Xen-users] Network configulation error in Windows Vista
BusinessHVM / Xen 3.04
That’s a known problem. Can you try
the driver from Windows 2003? The driver on the X64 seems to be working fine,
though.
Jun
---
Intel Open Source Technology Center
From:
xen-users-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Makoto Sakurai
Sent: Saturday, April 07, 2007 6:18 AM
To: xen-users@xxxxxxxxxxxxxxxxxxx
Cc: 'Makoto Sakurai'
Subject: [Xen-users] Network configulation error in Windows Vista
BusinessHVM / Xen 3.04
Dear all;
I am trying to set up the Windows Vista Business of
Japanese version on the Fedora Core 7 test 3, which has the rpm version of
xen-3.0.4-9.fc7. I have a success to install the Windows HVM with Pentium D 750
CPU. However, I cannot configure the network, which can be worked for the
Windows XP / Xen. My network card is on board card of Gigabyte GA-8I945G-MBX
motherboard, that is recognized as the eth0.
When we checked the bridge, we have the following
message;
[root@localhost makoto]# /usr/sbin/brctl show xenbr0
bridge name bridge id STP enabled interfaces
virbr0 8000.000000000000 no
xenbr0 8000.feffffffffff no peth0
vif0.0
peth0 is recognized as the Intel Corporation 82573V
Gigabit Ethernet Controller (Copper) card under the Gnome network
configulation.
After downloading the Realtek driver, I can improved
the network status as “local and internet”; however, the network is
still “unrecognized network”, which I do not know why?
Is there anyone who have tried to install the Windows
Vista and which is successful?
I would appreciate if you would give me some advice.
Best wishes,
Makoto Sakurai
__________ Informace od NOD32 2221 (20070426) __________
Tato zprava byla proverena antivirovym systemem NOD32.
http://www.nod32.cz
Home