Basically the issue comes down to my Volume Groups not being found by
this initrd, causing good ole kernel panic.
initrd-2.6.12.6-xen3_12.1_rhel4.1.img
[root@xen01 lvm]# uname -a
Linux xen01.inside.***.com 2.6.9-22.0.2.ELsmp #1 SMP Thu Jan 5 17:13:01
EST 2006 i686 i686 i386 GNU/Linux
[root@xen01 lvm]# cat /etc/redhat-release
Red Hat Enterprise Linux ES release 4 (Nahant Update 2)
Everything was installed by the rpms, as I've done another machine that
wasn't scsi, and had this work fine.
The part I'm worried about is this:
" Couldn't find all physical volumes for volume group VolGroup00."
I have sda, and sdb in a software mirror, as shown below, and I'm
thinking that has something to do with it.
[root@xen01 ~]# pvscan
PV /dev/sdc1 VG VolGroup00 lvm2 [68.34 GB / 0 free]
PV /dev/md2 VG VolGroup00 lvm2 [66.25 GB / 64.00 MB free]
Total: 2 [134.59 GB] / in use: 2 [134.59 GB] / in no VG: 0 [0 ]
[root@xen01 ~]# vgscan
Reading all physical volumes. This may take a while...
Found volume group "VolGroup00" using metadata type lvm2
[root@xen01 ~]# lvscan
ACTIVE '/dev/VolGroup00/LogVolRoot' [8.00 GB] inherit
ACTIVE '/dev/VolGroup00/LogVolTmp' [4.00 GB] inherit
ACTIVE '/dev/VolGroup00/LogVolVar' [4.00 GB] inherit
ACTIVE '/dev/VolGroup00/LogVolXen' [118.53 GB] inherit
sda1:sdb1 = boot (100MB)
sda2:sdb2 = swap (2048MB)
sda3:sdb3 = Lvm
sdc = Lvm
[root@xen01 boot]# lsmod | grep mpt
mptscsih 41469 0
mptbase 57757 1 mptscsih
scsi_mod 116429 3 sg,mptscsih,sd_mod
Does anyone have any suggestions on the steps I should take next to
debug this?
Thanks everyone.
*************** Lots of dmesg output follows, beware *******************
Loading scsi_mod.ko module
scsi_mod: no version for "struct_module" found: kernel tainted.
SCSI subsystem initialized
Loading sd_mod.ko module
Loading mptbase.ko module
Fusion MPT base driver 3.01.20
Copyright (c) 1999-2004 LSI Logic Corporation
ACPI: PCI Interrupt 0000:04:05.0[A] -> GSI 18 (level, low) -> IRQ 18
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator,Target}
ACPI: PCI Interrupt 0000:04:05.1[B] -> GSI 19 (level, low) -> IRQ 19
mptbase: Initiating ioc1 bringup
ioc1: 53C1030: Capabilities={Initiator,Target}
Loading mptscsih.ko module
Fusion MPT SCSI Host driver 3.01.20
scsi0 : ioc0: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=255, IRQ=18
Vendor: FUJITSU Model: MAP3735NC Rev: 5608
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 143374650 512-byte hdwr sectors (73408 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 143374650 512-byte hdwr sectors (73408 MB)
SCSI device sda: drive cache: write through
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: FUJITSU Model: MAP3735NC Rev: 5608
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sdb: 143374650 512-byte hdwr sectors (73408 MB)
SCSI device sdb: drive cache: write through
SCSI device sdb: 143374650 512-byte hdwr sectors (73408 MB)
SCSI device sdb: drive cache: write through
sdb: sdb1 sdb2 sdb3
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
Vendor: FUJITSU Model: MAP3735NC Rev: 5608
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sdc: 143374650 512-byte hdwr sectors (73408 MB)
SCSI device sdc: drive cache: write through
SCSI device sdc: 143374650 512-byte hdwr sectors (73408 MB)
SCSI device sdc: drive cache: write through
sdc: sdc1
Attached scsi disk sdc at scsi0, channel 0, id 2, lun 0
Vendor: PE/PV Model: 1x3 SCSI BP Rev: 1.1
Type: Processor ANSI SCSI revision: 02
scsi1 : ioc1: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=255, IRQ=19
Loading dm-mod.ko module
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx
Loading md.ko module
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Loading raid1.ko module
md: raid1 personality registered as nr 3
Loading jbd.ko module
Loading ext3.ko module
Loading dm-mirror.ko module
Loading dm-zero.ko module
Loading dm-snapshot.ko module
raidautorun: RAID_AUTORUN failed: 19
raidautorun: RAID_AUTORUN failed: 19
raidautorun: RAID_AUTORUN failed: 19
Making device-mapper control node
Scanning logical volumes
File descriptor 3 left open
Reading all physical volumes. This may take a while...
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54 { AbortedCommand
LastFailedSense=0x05 }
ide: failed opcode was: unknown
cdrom: open failed.
/dev/hdc: open failed: No medium found
Couldn't find device with uuid 'v6mYx2-YWLn-1MNL-Z3nl-HKoa-qNna-Thhd6y'.
Couldn't find all physical volumes for volume group VolGroup00.
Volume group "VolGroup00" not found
ERROR: /bin/lvm exited abnormally!
--
Michael Montgomery
Systems Administrator
http://theplanet.com
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home