RE: [Xen-ia64-devel] Could you tell me howto run xen on ski?

["Magenheimer, Dan (HP Labs Fort Collins)" <dan.magenheimer@xxxxxx>]

One other possible problem:  I think you need to specify
the command line as: 

# xski bootloader vmlinux simscsi=/nue/var/ski-disks/sd

Note that you need to leave the "a" off of "sda" in the
simscsi= line but the filename is still sda.

Dan

> -----Original Message-----
> From: xen-ia64-devel-bounces@xxxxxxxxxxxxxxxxxxx 
> [mailto:xen-ia64-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf 
> Of Magenheimer, Dan (HP Labs Fort Collins)
> Sent: Friday, December 02, 2005 8:02 AM
> To: Matsumoto; xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
> Subject: RE: [Xen-ia64-devel] Could you tell me howto run xen on ski?
> 
> I have often used ski for Xen development but have not tried
> it in a few months.  However I never tried to use networking
> (simeth).  Did you build the vmlinux with the hpsim config
> file or just turn on CONFIG_HP_SIM?   Also I think the command
> line options you are specifying may be wrong... I will
> have to try it again to check (and may not be able to
> try until next week as I am focused on Xen 3.0 release
> right now).
> 
> > -----Original Message-----
> > From: xen-ia64-devel-bounces@xxxxxxxxxxxxxxxxxxx 
> > [mailto:xen-ia64-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf 
> > Of Matsumoto
> > Sent: Friday, December 02, 2005 2:53 AM
> > To: xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
> > Subject: [Xen-ia64-devel] Could you tell me howto run xen on ski?
> > 
> > Hi, all
> > 
> > I am interested in running ski for Xen development.
> > 
> > First, I tried to run native vmlinux(which is complied with 
> > CONFIG_HP_SIM
> > and so on).
> > 
> > But I have not been able to boot vmlinux.
> > 
> > # xski bootloader vmlinux root=/dev/sda1 
> > simscsi=/nue/var/ski-disks/sda
> > simeth=eth0
> > 
> > The result is :
> > 
> > ==================================================
> > 
> > loading vmlinux...
> > 
> > starting kernel...
> > 
> > Linux version 2.6.12 (root@xxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc 
> > version 3.4.4
> > 
> > 20050721 (Red Hat 3.4.4-2)) #1 SMP Fri Dec 2 13:43:29 JST 
> > 2005 EFI v1.00 by
> > Hewlett-Packard: SALsystab=0x10a0b8
> > 
> > warning: unable to switch EFI into virtual mode 
> > (status=9223372036854775811)
> > No I/O port range found in EFI memory map, falling back to 
> > AR.KR0 I/O port
> > base = 0xffffc000000
> > 
> > efi.trim_top: ignoring 2048KB of memory at 0x200000 due to 
> > granule hole at
> > 0x8000000
> > 
> > warning: skipping physical page 0
> > 
> > SAL 0.1: Hewlett-Packard HP-simulator version 0.0 No logical 
> > to physical
> > processor mapping available
> > 
> > get_max_cacheline_size: ia64_pal_cache_summary() failed (status=-1)
> > PAL_VM_PAGE_SIZE failed with status=-1;defaulting to 
> architected purge
> > page-sizes.
> > 
> > cpu_init: PAL VM summary failed, assuming 18 RID bits MCA related
> > initialization done Virtual mem_map starts at 
> > 0xa0007fffff1e4000 Built 1
> > zonelists Kernel command line: root=/dev/sda1 
> > simscsi=/root/ski/xenia64.img
> > simeth=eth0 PID hash table entries: 1024 (order: 10, 32768 
> bytes) :-<
> > "Processing stops here. "
> > 
> > ==================================================
> > 
> > Did I mistake anything?
> > 
> > Please tell me howto run xen on ski if anyone use ski.
> > 
> > Thanks,
> > 
> > Nakato
> > 
> > 
> > 
> > _______________________________________________
> > Xen-ia64-devel mailing list
> > Xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
> > http://lists.xensource.com/xen-ia64-devel
> > 
> 
> _______________________________________________
> Xen-ia64-devel mailing list
> Xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-ia64-devel
> 

_______________________________________________
Xen-ia64-devel mailing list
Xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-ia64-devel