| |
|
 |
|
 |
|
|
|
| |
|
|
xen-devel
Re: [Xen-devel] debugging Xen in a serial-less environment
Gerd Hoffmann wrote:
Christian Tramnitz wrote:
I'm currently trying to debug a couple of iommu issues I'm experiencing
on a X58 board with VT-d while passing through hardware into a Windows
HVM domU, but unfortunately it seems legacy hardware was deemed obsolete
and not a single serial port is provided by the board (Asus P6T Deluxe
for that matter).
Are there any alternatives to the Xen console on serial or vga?
Does the box have AMT? The you can use serial-over-lan.
There's the USB debug port stuff which got added to the kernel a while
ago. Looks like it shouldn't be too hard to graft into Xen.
J
Mini-HOWTO for using the earlyprintk=dbgp boot option with a
USB2 Debug port key and a debug cable, on x86 systems.
You need two computers, the 'USB debug key' special gadget and
and two USB cables, connected like this:
[host/target] <-------> [USB debug key] <-------> [client/console]
1. There are three specific hardware requirements:
a.) Host/target system needs to have USB debug port capability.
You can check this capability by looking at a 'Debug port' bit in
the lspci -vvv output:
# lspci -vvv
...
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #1 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo ThinkPad T61
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fe227000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [58] Debug port: BAR=1 offset=00a0
^^^^^^^^^^^ <==================== [ HERE ]
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
...
( If your system does not list a debug port capability then you probably
wont be able to use the USB debug key. )
b.) You also need a Netchip USB debug cable/key:
http://www.plxtech.com/products/NET2000/NET20DC/default.asp
This is a small blue plastic connector with two USB connections,
it draws power from its USB connections.
c.) Thirdly, you need a second client/console system with a regular USB port.
2. Software requirements:
a.) On the host/target system:
You need to enable the following kernel config option:
CONFIG_EARLY_PRINTK_DBGP=y
And you need to add the boot command line: "earlyprintk=dbgp".
(If you are using Grub, append it to the 'kernel' line in
/etc/grub.conf)
NOTE: normally earlyprintk console gets turned off once the
regular console is alive - use "earlyprintk=dbgp,keep" to keep
this channel open beyond early bootup. This can be useful for
debugging crashes under Xorg, etc.
b.) On the client/console system:
You should enable the following kernel config option:
CONFIG_USB_SERIAL_DEBUG=y
On the next bootup with the modified kernel you should
get a /dev/ttyUSBx device(s).
Now this channel of kernel messages is ready to be used: start
your favorite terminal emulator (minicom, etc.) and set
it up to use /dev/ttyUSB0 - or use a raw 'cat /dev/ttyUSBx' to
see the raw output.
c.) On Nvidia Southbridge based systems: the kernel will try to probe
and find out which port has debug device connected.
3. Testing that it works fine:
You can test the output by using earlyprintk=dbgp,keep and provoking
kernel messages on the host/target system. You can provoke a harmless
kernel message by for example doing:
echo h > /proc/sysrq-trigger
On the host/target system you should see this help line in "dmesg" output:
SysRq : HELP : loglevel(0-9) reBoot Crashdump terminate-all-tasks(E)
memory-full-oom-kill(F) kill-all-tasks(I) saK show-backtrace-all-active-cpus(L)
show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P)
show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W)
dump-ftrace-buffer(Z)
On the client/console system do:
cat /dev/ttyUSB0
And you should see the help line above displayed shortly after you've
provoked it on the host system.
If it does not work then please ask about it on the linux-kernel@xxxxxxxxxxxxxxx
mailing list or contact the x86 maintainers.
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
|
|
| |
|
Home