Hi Matthias,
sadly, nogplpv options does not have any effect in my case (still blue
screen)
with nogplpv option but without disabling digital signatures with F8:
error because of digital signature.
(it's "bcdedit /copy {oldid} /d" name and
"bcdedit /set {newid} loadoptions nogplpv" right?)
with nogplpv and with disabled digital signatures: blue screen
STOP: 0x7B
did you use a file, or a real partition (maybe an lvm-volume)?
I am using
disk = [ 'file:/path/to/hda.img,hda,w' ]
regards,
Max
Matthias Reif wrote:
>
> Max,
>
> I had the same bluescreen 0x7b on reboot after installing the GPLPV
> (0.10.0.69) drivers onto a Windows 2008 64-bit domU.
>
> What fixed it for me was a reboot with the NOGPLPV boot option and then
> reboot again with the GPLPV drivers enabled. The blue screen did not
> re-occur since.
>
> Thanks
> Matthias
>
>
>
>
>
> *_Matthias Reif_*
> *Max-Julian Pogner <mjp@xxxxxxxxxxxx>*
> Sent by: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
>
> 20/05/2009 01:30 AM
>
>
> To
> xen-users@xxxxxxxxxxxxxxxxxxx
> cc
>
>
>
> Subject
> [Xen-users] Bluescreen after installing gplpv 0.10.0.69
>
>
>
>
>
>
>
>
> Hi all,
>
>
> I'm setting up Windows 2008 64bit on xen+hvm
>
> after windows setup has finished, I installed the drivers with
> gplpv_fre_wlh_AMD64_0.10.0.69.msi and
> a) either get an digital signature error, OR when disabling signature
> checking via Pressing F8 during boot, get
> b) a Bluescreen with a STOP: 0x00007B error.
>
> I have tried
> - DSEO from http://www.ngohq.com/home.php?page=dseo
> (gives same bluescreen),
> - importing james harper's signature as CA/etc, no change.
> (windows still does not recognize xenpci.sys as digitally signed)
>
>
> As far as I grasp the idea, the blue screen should be unrelated to the
> digital-signature issue, since that is temporarily "resolved" by the F8
> option to disable signature verification.
>
> 0x7B means that windows has some device issues, so the xen drivers do
> not load despite disabling the digital signature?
>
>
> additionally I have seen, that after installing the drivers, but before
> reboot, the device manager lists the xenpci.sys driver for the Xen PV
> PCI device as "not signed" (but the .sys file has Harper's siganture
> according to it's file-properties).
>
>
>
> Any ideas?
>
>
> regards,
>
>
> Max Pogner
>
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users
>
>
>
>
> *SOUTH PACIFIC SEEDS*
> PO Box 934, GRIFFITH N.S.W. 2680. AUSTRALIA/
> Phone:/ 02 6962 7333 /Fax:/ 02 6964 1311
> ------------------------------------------------------------------------
> _CAUTION:_ The information contained in this e-mail is privileged and
> confidential. If you are reading this message and you are not the
> intended recipient, you are hereby notified that any use, dissemination,
> distribution or reproduction of all or part of the contents is
> prohibited. If you receive this message in error, please notify the
> sender immediately. Any opinions or views expressed in this message are
> those of the individual sender and may not represent those of their
> employer.
>
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home