 Home |
Products |
Support |
Community |
News |
xen-users
[Xen-users] How to setup two NIC with NAT networking between domUs?
| To: | "Xen Users Mailing List" <xen-users@xxxxxxxxxxxxxxxxxxx>, "xen-users-request@xxxxxxxxxxxxxxxxxxx" <xen-users-request@xxxxxxxxxxxxxxxxxxx> |
|---|---|
| Subject: | [Xen-users] How to setup two NIC with NAT networking between domUs? |
| From: | "Eric Jansen" <janseneric@xxxxxxxxx> |
| Date: | Mon, 8 Dec 2008 22:58:23 +0100 |
| Delivery-date: | Mon, 08 Dec 2008 13:59:11 -0800 |
| Dkim-signature: | v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=gamma; h=domainkey-signature:received:received:message-id:date:from:to :subject:mime-version:content-type; bh=wJaZhhdcrLExWz2tLXfpZ8KXYDOlv4qlnsZmz0rjH+I=; b=gFwkzhQWvk4Fo5X/CcRVxrWpNNqj8ev1ah3FfVt0hJi13MlrwjDgHqHo5vST+WlDHm uzATgnpm6V8l0iRmnpGBNBAw0oOGhQk4u6z9CEPeN+TOsVDTIctZHNmMbAhACbkUGE4D +fGx2wD7y+URL+9Nyw3DkcRUGnlhSnKMgpHD8= |
| Domainkey-signature: | a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=message-id:date:from:to:subject:mime-version:content-type; b=jhU0T6doiLkjzxYVcsXSn4wySwIXayHeVsjAqOkvlxkZ3/QhcmESv7CSrdOVlTbXqS iU5Oitm35ZMVSjbo4+XHwX2a1Nrh3gkCfR5YlFU4gdkk5VbXJBWewBmdCennkvpeVCsl aedUca5e093WM0g5qYwfgkKLR/aceQAq6hiKs= |
| Envelope-to: | www-data@xxxxxxxxxxxxxxxxxxx |
| List-help: | <mailto:xen-users-request@lists.xensource.com?subject=help> |
| List-id: | Xen user discussion <xen-users.lists.xensource.com> |
| List-post: | <mailto:xen-users@lists.xensource.com> |
| List-subscribe: | <http://lists.xensource.com/mailman/listinfo/xen-users>, <mailto:xen-users-request@lists.xensource.com?subject=subscribe> |
| List-unsubscribe: | <http://lists.xensource.com/mailman/listinfo/xen-users>, <mailto:xen-users-request@lists.xensource.com?subject=unsubscribe> |
| Sender: | xen-users-bounces@xxxxxxxxxxxxxxxxxxx |
|
Hi all, I have set up 2 ethernet cards (one of them were previously built-in) and the CentOS dom0 recognized them, moreover, the domUs were configured with NAT. Would you mind pointing me how to configure eth1 to be found on domUs and how to setup the NAT with eth1? note: I set up the domUs eth0 NAT with range : 10.0.0.5-10.0.0.9 (gateway:10.0.0.1,netmask:255.0.0.0,broadcast:10.255.255.255), and I would like to set up eth1 NAT with ip range: 192.168.10.5-192.168.10.9 (gateway:192.168.10.1,netmask:255.255.255.0,broadcast:192.168.10.255) -- Eric Jansen _______________________________________________ Xen-users mailing list Xen-users@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-users |
| <Prev in Thread] | Current Thread | [Next in Thread> |
|---|---|---|
| ||
| Previous by Date: | Re: [Xen-users] [VT-D]iommu.c:775: iommu_page_fault: iommu->reg = ffff828bfff57000, daballiemo |
|---|---|
| Next by Date: | [Xen-users] kernel BUG pci-dma-xen.c:361!, josef.navratil |
| Previous by Thread: | [Xen-users] Easy way to remove GPLPV drivers version 0.9.10?, James Pifer |
| Next by Thread: | [Xen-users] kernel BUG pci-dma-xen.c:361!, josef.navratil |
| Indexes: | [Date] [Thread] [Top] [All Lists] |
