WARNING - OLD ARCHIVES

This is an archived copy of the Xen.org mailing list, which we have preserved to ensure that existing links to archives are not broken. The live archive, which contains the latest emails, can be found at http://lists.xen.org/
   
 
 
Xen 
 
Home Products Support Community News
 
   
 

xen-users

Re: [Xen-users] help--dom0 network goes unpingable when xend starts

By following the section of the following wiki:

http://mywiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround

in particular downloading the broadcom netextreme MS-DOS utilities
mentioned there, booting under DOS, and disabling the IPMI
network management on both broadcom nic's on the poweredge 1950,
I can now see the network from dom0 and domU after the Xen instance
is started up.  This works both with single bridge and dual bridge
configurations.

Steve Timm




On Mon, 5 May 2008, Steven Timm wrote:

Here's another update.  Some wiki's suggested that a
firmware upgrade on the NIC and on the PE1950 bios would solve
the problem. Unfortunately it did not. Problem is exactly
the same as before--that the network will boot OK for starters but
as soon as xend is started up (before any domu's start) the
network locks up totally and dom0 is unpingable from the outside.
It can ping any domu's it starts and the domu's can ping it, and
also get to the outside world.

I've looked through the network wiki but thus far have not found
the right diagnostics that I should be checking.

Does anyone have Xen 3.1 working on a poweredge 1950? IF so, what did
you do?

Steve


On Thu, 17 Apr 2008, Steven Timm wrote:

I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on
three new machines today, using a configuration setup that I've
used successfully many times before.  However, I encountered  a
new problem.

These are Dell Poweredge 1950 servers, by the way.
From lspci
04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12)

from lspci
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, 2006)
ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at
mem f4000000, IRQ 16, node addr 0019b9ec40ba
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at
mem f8000000, IRQ 16, node addr 0019b9ec40b8

---------------

note that the Xen kernel 2.6.18 picks the opposite mac addresses as eth0
from what the redhatized non-xen kernel does.  This is
undone by ifcfg-eth0.

When the xen kernel boots, before xend starts, I can see the outside network just fine.

[root@fnpcsrv3 xen]# netstat -nNr
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.167.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 131.225.166.0 0.0.0.0 255.255.254.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 131.225.167.200 0.0.0.0 UG 0 0 0 eth0


[root@fnpcsrv3 xen]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:19:B9:EC:40:B8
         inet addr:131.225.166.97  Bcast:131.225.167.255 Mask:255.255.254.0
         inet6 addr: fe80::219:b9ff:feec:40b8/64 Scope:Link
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:591697 errors:0 dropped:0 overruns:0 frame:0
         TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:38067586 (36.3 MiB)  TX bytes:395536 (386.2 KiB)
         Interrupt:16 Memory:f8000000-f8011100

eth1      Link encap:Ethernet  HWaddr 00:19:B9:EC:40:BA
         inet addr:192.168.167.3  Bcast:192.168.167.255 Mask:255.255.255.0
         UP BROADCAST MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
         Interrupt:16 Memory:f4000000-f4011100

lo        Link encap:Local Loopback
         inet addr:127.0.0.1  Mask:255.0.0.0
         inet6 addr: ::1/128 Scope:Host
         UP LOOPBACK RUNNING  MTU:16436  Metric:1
         RX packets:192 errors:0 dropped:0 overruns:0 frame:0
         TX packets:192 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:15314 (14.9 KiB)  TX bytes:15314 (14.9 KiB)
--------------------------------------------------------------

Now here's ifconfig from an identical system once xend is turned on

[root@fnpcsrv5 ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:19:B9:EC:4A:21
inet addr:131.225.166.100 Bcast:131.225.167.255 Mask:255.255.254.0
         inet6 addr: fe80::219:b9ff:feec:4a21/64 Scope:Link
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:508292 errors:0 dropped:0 overruns:0 frame:0
         TX packets:33 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:30786266 (29.3 MiB)  TX bytes:1658 (1.6 KiB)

lo        Link encap:Local Loopback
         inet addr:127.0.0.1  Mask:255.0.0.0
         inet6 addr: ::1/128 Scope:Host
         UP LOOPBACK RUNNING  MTU:16436  Metric:1
         RX packets:21 errors:0 dropped:0 overruns:0 frame:0
         TX packets:21 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:1916 (1.8 KiB)  TX bytes:1916 (1.8 KiB)

peth0     Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
         inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
         UP BROADCAST RUNNING NOARP  MTU:1500  Metric:1
         RX packets:523679 errors:0 dropped:0 overruns:0 frame:0
         TX packets:15964 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:33836052 (32.2 MiB)  TX bytes:1132609 (1.0 MiB)
         Interrupt:16 Memory:f4000000-f4011100

vif0.0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
         inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
         UP BROADCAST RUNNING NOARP  MTU:1500  Metric:1
         RX packets:33 errors:0 dropped:0 overruns:0 frame:0
         TX packets:508293 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:1658 (1.6 KiB)  TX bytes:30786336 (29.3 MiB)

vif1.0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
         inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
         UP BROADCAST RUNNING NOARP  MTU:1500  Metric:1
         RX packets:7848 errors:0 dropped:0 overruns:0 frame:0
         TX packets:499340 errors:0 dropped:159 overruns:0 carrier:0
         collisions:0 txqueuelen:32
         RX bytes:347417 (339.2 KiB)  TX bytes:30239848 (28.8 MiB)

vif2.0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
         inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
         UP BROADCAST RUNNING NOARP  MTU:1500  Metric:1
         RX packets:7867 errors:0 dropped:0 overruns:0 frame:0
         TX packets:496186 errors:0 dropped:191 overruns:0 carrier:0
         collisions:0 txqueuelen:32
         RX bytes:346478 (338.3 KiB)  TX bytes:30050363 (28.6 MiB)

xenbr0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:508099 errors:0 dropped:0 overruns:0 frame:0
         TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:23650570 (22.5 MiB)  TX bytes:90 (90.0 b)

xenbr1    Link encap:Ethernet  HWaddr 00:00:00:00:00:00
         inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:0 (0.0 b)  TX bytes:468 (468.0 b)

------------------------------------------------------------------------

As part of the debugging I dialed back my configuration, which normally
has a xenbr0 and a xenbr1, to use a just a xenbr0 and have just one
network interface on each domU and on the dom0.  Nevertheless the
problem is the same and I can't seem to get rid of the xenbr1.
I note that at the start of the xend there is a timeout of about 10-15
seconds as it is trying to turn on the second bridge.

Now here is the really strange part.  While logged in on the
console of the dom0, I can go ahead and start xen domU's, and they
go ahead and boot up normally and can see the outside network fine.

[root@fnpcsrv5 ~]# xm list
Name                                      ID   Mem VCPUs      State Time(s)
Domain-0 0 1953 8 r----- 127.3 fnpc5x1 1 6000 4 -b---- 23.1 fnpc5x4 2 2000 1 -b---- 20.6
[root@fnpcsrv5 ~]#

Oh, and by the way, dom0 is pingable from the domU's although
it cannot be seen from the outside net.

What should I be looking at?

Steve Timm



------------------------------------------------------------------
Steven C. Timm, Ph.D  (630) 840-8525
timm@xxxxxxxx  http://home.fnal.gov/~timm/
Fermilab Computing Division, Scientific Computing Facilities,
Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader.

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users




--
------------------------------------------------------------------
Steven C. Timm, Ph.D  (630) 840-8525
timm@xxxxxxxx  http://home.fnal.gov/~timm/
Fermilab Computing Division, Scientific Computing Facilities,
Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader.

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

<Prev in Thread] Current Thread [Next in Thread>