Hello everyone,
I can’t seem to figure out why when I specify a kick-start;
the network can never be found on a dual bridged xen setup…
However if I do the installation manually it works smoothly….
My configuration;
Xen version
3.1.0-rc7-2950.fc8
running on Fedora 8
The command I’m using to do the kickstart
install is:
virt-install -n test -r 256
\
-f
/var/xen/default/test-default.dsk -s 5 \
-f
/var/xen/default/test-swap.dsk -s 5 \
-p
--location=http://10.1.1.1/cldn \
--nographics \
--bridge=eth0
--mac=00:16:3e:00:00:00 \
--bridge=eth1
--mac=00:16:3e:00:00:01 \
--os-type='linux' \
--vcpus=1 \
-x "ks=http://10.1.1.1/cldn01-ks.cfg"
(even without reference to the second bridge it
doesn’t work)
In the kickstart file; I set the address I want the
virtual machine to assume (for ethernet 0)
If I do a manual install and specify these entries,
everything seems to work… but this link (supposedly automating the
install) does not work:
network --bootproto=static
--device=eth0 --ip=10.1.1.2 --netmask=255.255.255.0--gateway=10.1.1.250 --
--hostname=cldn01.c1
First I get stuck on this screen (with the kickstart)
------
Welcome to Fedora for i386
+---------+ Networking Device +----------+
|
|
| You have multiple network devices on |
| this system. Which would you like to |
| install
through?
|
|
|
| eth0 - Xen Virtual
Ethernet |
| eth1 - Xen Virtual
Ethernet |
|
|
|
+----+
+------+ |
| | OK
| |
Back | |
|
+----+
+------+ |
|
|
|
|
+----------------------------------------+
<Tab>/<Alt-Tab> between
elements | <Space> selects | <F12> next screen
After I choose eth0 (as this is the network I install
from the http server) it hangs forever here…
Welcome to Fedora for i386
+-------------------------------------------------------+
|
|
| Sending request for IP information for
eth0... |
|
|
+-------------------------------------------------------+
<Tab>/<Alt-Tab> between
elements | <Space> selects | <F12> next screen
… I specifically set the bootproto to ‘not’
use dhcp yet it still persists to run…
Here is my network information:
eth0
Link encap:Ethernet HWaddr 00:22:43:EB:15:79
inet addr: 10.1.1.1 Bcast: 10.1.1.255 Mask:255.255.255.0
inet6 addr: fe80::211:43ff:feeb:1579/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1780014 errors:0 dropped:0 overruns:0 frame:0
TX packets:825913 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:437644968 (417.3 MiB) TX bytes:572632433 (546.1 MiB)
eth1
Link encap:Ethernet HWaddr 00:22:43:EB:15:7A
inet addr:172.1.0.2 Bcast:172.1.255.255 Mask:255.255.0.0
inet6 addr: fe80::211:43ff:feeb:157a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1084056 errors:0 dropped:0 overruns:0 frame:0
TX packets:160 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:344078469 (328.1 MiB) TX bytes:11698 (11.4 KiB)
lo
Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1563262 errors:0 dropped:0 overruns:0 frame:0
TX packets:1563262 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3170783887 (2.9 GiB) TX bytes:3170783887 (2.9 GiB)
peth0
Link encap:Ethernet HWaddr 00:11:43:EB:15:79
inet6 addr: fe80::211:43ff:feeb:1579/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1821237 errors:0 dropped:0 overruns:0 frame:0
TX packets:826115 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:472306027 (450.4 MiB) TX bytes:575959158 (549.2 MiB)
Interrupt:18
peth1
Link encap:Ethernet HWaddr 00:11:43:EB:15:7A
inet6 addr: fe80::211:43ff:feeb:157a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1125669 errors:0 dropped:0 overruns:0 frame:0
TX packets:166 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:366268811 (349.3 MiB) TX bytes:14656 (14.3 KiB)
Interrupt:19
My bridges appear to be in place as well:
$>brctl show
bridge
name bridge
id
STP enabled interfaces
eth0
8000.001143eb1579
no
peth0
eth1
8000.001143eb157a
no
peth1
This is my custom bridge script:
#!/bin/sh
dir=$(dirname
"$0")
"$dir/network-bridge"
"$@" vifnum=0 netdev=eth0 bridge=eth0
"$dir/network-bridge"
"$@" vifnum=1 netdev=eth1 bridge=eth1
Perhaps my problem is related to the fact that
netdev = the bridge?
eth0 and eth1 have aliases in my etc/modprob.conf…
could they be conflicting?
Originally I was having problems using the xenbr0
and xenbr1 bridges…. It was always leaving a tmpbridge in my network and
never setting up the bridges properly.
What am I doing wrong?
Home