Thank you guys very very much for your patience and time.
I got winXP setup running with sdl.
I need to figure out why vnc isn't working but that's another story.
Thank again
Ben
Am Mittwoch, den 20.12.2006, 19:15 +0000 schrieb Ryan Worsley:
> Benny Pfitzner wrote:
> > Am Mittwoch, den 20.12.2006, 16:04 +0000 schrieb Ryan Worsley:
> >
> >> Hi Benny,
> >>
> >> Benny Pfitzner wrote:
> >>
> >>> Hi,
> >>>
> >>> I run debian etch with xen packages provided by debian. They are running
> >>> fine.
> >>> Today I tryed to install Windows XP. Here is my config:
> >>> ***********************************************
> >>> kernel = "/usr/lib/xen-3.0.3-1/boot/hvmloader"
> >>> builder = 'hvm'
> >>> memory = 512
> >>> name = "winxp"
> >>> vcpus = 1
> >>> vif = [ 'type=ioemu, bridge=xenbr0' ]
> >>> disk = [ 'file://vserver/images/domains/winxp/winxp.img,ioemu:hda,w' ]
> >>> device_model = '/usr/lib/xen/bin/qemu-dm'
> >>> #cdrom='/dev/hda'
> >>> cdrom='/vserver/images/domains/winxp/winxp.iso'
> >>>
> >>>
> >> The cdrom= lines had no effect for me, I think they're obsolete now or
> >> something, instead I have a disk line that looks like this;
> >>
> >> disk = [ 'phy:/dev/sys_vg/windows_os,ioemu:hda,w',
> >> 'file:/vserver/images/domains/winxp/winxp.iso,hdc:cdrom,r' ]
> >>
> >
> > Thank you very much Ryan,
> >
> > you are totally right. They changed it in version 3.0.3.
> >
> > I added vncviewer=1 and sdl=1 to my configfile and started the domain
> > again.
> >
>
> You're welcome man. I think it's intended that you use EITHER the vnc
> viewer OR the SDL viewer and not both simultaneously. Maybe someone can
> clear up the technicality of this?
> > Then I automatically I got vncviewer running my WinXP install screen.
> > After formatting the image and so on Windows want's to reboot.
> >
> > Since then I don't have connection to the domain.
> >
> Is it the VNC viewer you've got or an SDL viewer, the top of the window
> should give it away. You say it reboots but you have no connection to
> the domain, this may be something to do with having both vnc and sdl on
> at the same time. In my experience with SDL, you get a new window pop
> up after the reboot. Not so sure with VNC though.
> > I posted my netstat -l output here because I just can't find the port:
> > http://pastebin.ca/raw/286397
> >
>
> The only line pertaining to VNC looks like this one;
>
> tcp 0 0 localhost.localdom:5900 *:* LISTEN
>
>
>
> But that said, this is more than likely just the vncserver you have
> running on Dom0. So it looks to me that perhaps having both vnc and sdl
> enabled might be causing problems!
> > My logs don't show anything regarding vnc.
> > Here is the output of the most recent qemu-log:
> > *************************************************
> > domid: 7
> > qemu: the number of cpus is 1
> > shared page at pfn:1ffff, mfn: 1d24b
> > buffered io page at pfn:1fffd, mfn: 1d24d
> > *************************************************
> >
> > Here I posted the last couple of lines from the xend.log file.
> > http://pastebin.ca/286403
> >
> This all looks fine to me.
>
> Thanks,
>
> Ryan.
> >
> > Thanks Ben
> >
> >
> >>> ne2000=0
> >>> boot='d'
> >>> vif = [ 'ip=192.168.0.205' ]
> >>> vnc=1
> >>> vncviewer=0
> >>>
> >>>
> >> Do you not have to set vncviewer to 1 to get it create the window for
> >> you? I personally used SDL instead (sdl=1). You also say your domain
> >> is 17, I think when I experimented with VNC I found it to create the
> >> listening port on something like 4017 or whatever. I used netstat -l to
> >> find out what port it was actually on.
> >>
> >> Ben, lastly, could you check your /var/log/xen folder for error
> >> messages, specifically check the most recent qemu log.
> >>
> >> Thanks,
> >>
> >> Ryan.
> >>
> >>> ***********************************************
> >>>
> >>> When I try to start the domain it seems to run fine:
> >>> ***********************************************
> >>> pfitzner:/etc/xen# xm create winxp2
> >>> Using config file "winxp2".
> >>> Started domain winxp
> >>> ***********************************************
> >>>
> >>> But when I try to connect to the domain via vnc I get the message that
> >>> the viewer can't connect:
> >>> ***********************************************
> >>> pfitzner:/vserver/images/domains# vncviewer pfitzner:17
> >>> vncviewer: ConnectToTcpAddr: connect: Connection refused
> >>> Unable to connect to VNC server
> >>> ***********************************************
> >>>
> >>> P.S.:
> >>> 17 is the ID of the domain and I have a Intel Pentuim D with VT:
> >>> pfitzner:/vserver/images/domains# xm dmesg | grep VMX
> >>> (XEN) VMXON is done
> >>> (XEN) VMXON is done
> >>>
> >>>
> >>> Does somebody might have a idea what I did do wrong?
> >>>
> >>> Tanks Ben
> >>>
> >>>
> >>> _______________________________________________
> >>> Xen-users mailing list
> >>> Xen-users@xxxxxxxxxxxxxxxxxxx
> >>> http://lists.xensource.com/xen-users
> >>>
> >>>
> >> _______________________________________________
> >> Xen-users mailing list
> >> Xen-users@xxxxxxxxxxxxxxxxxxx
> >> http://lists.xensource.com/xen-users
> >>
> >
> >
> > _______________________________________________
> > Xen-users mailing list
> > Xen-users@xxxxxxxxxxxxxxxxxxx
> > http://lists.xensource.com/xen-users
> >
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home