Stephan,
I finally got a chance to build Xen 3.0 with QLogic as a module and it
works just as before. I've sent my config file privately for you to
compare.
.githogori.
-----------------------------------------------------------
[root@localhost ~]# uname -a
Linux localhost.localdomain 2.6.12-xen0-3.0-gQmodule #7 SMP Wed Oct 12
12:51:44 PDT 2005 i686 i686 i386 GNU/Linux
[root@localhost ~]#
---------------------------------------------------------------
[root@localhost ~]# modprobe qla2300
[root@localhost ~]# mount /dev/sdb /mnt/FCvol
[root@localhost ~]#
---------------------------------------------------------------
WHAT I SEE ON MY SERIAL CONSOLE:
0 00 00
<6>note: smflsh4lx[5046] exited with preempt_count 1
QLogic Fibre Channel HBA Driver
ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 37 (level, low) -> IRQ 37
qla2300 0000:02:0b.0: Found an ISP2312, irq 37, iobase 0xe0068000
scsi1 : qla2xxx
qla2300 0000:02:0b.0: Configuring PCI space...
qla2300 0000:02:0b.0: Configure NVRAM parameters...
qla2300 0000:02:0b.0: Verifying loaded RISC code...
qla2300 0000:02:0b.0: Waiting for LIP to complete...
qla2300 0000:02:0b.0: Cable is unplugged...
qla2300 0000:02:0b.0:
QLogic Fibre Channel HBA Driver: 8.00.02b5-k
QLogic QLA2342 - 133MHz PCI-X to 2Gb FC, Dual Channel
ISP2312: PCI-X (133 MHz) @ 0000:02:0b.0 hdma-, host#=1, fw=3.03.08 IPX
ACPI: PCI Interrupt 0000:02:0b.1[B] -> GSI 38 (level, low) -> IRQ 38
qla2300 0000:02:0b.1: Found an ISP2312, irq 38, iobase 0xe0070000
scsi2 : qla2xxx
qla2300 0000:02:0b.1: Configuring PCI space...
qla2300 0000:02:0b.1: Configure NVRAM parameters...
qla2300 0000:02:0b.1: Verifying loaded RISC code...
qla2300 0000:02:0b.1: Waiting for LIP to complete...
qla2300 0000:02:0b.1: LIP reset occured (f8f7).
qla2300 0000:02:0b.1: LIP occured (f8f7).
qla2300 0000:02:0b.1: LOOP UP detected (1 Gbps).
qla2300 0000:02:0b.1: Topology - (Loop), Host Loop address 0x7d
qla2300 0000:02:0b.1:
QLogic Fibre Channel HBA Driver: 8.00.02b5-k
QLogic QLA2342 - 133MHz PCI-X to 2Gb FC, Dual Channel
ISP2312: PCI-X (133 MHz) @ 0000:02:0b.1 hdma-, host#=2, fw=3.03.08 IPX
Vendor: DGC Model: RAID 5 Rev: 0411
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 68317440 512-byte hdwr sectors (34979 MB)
sdb: cache data unavailable
sdb: assuming drive cache: write through
SCSI device sdb: 68317440 512-byte hdwr sectors (34979 MB)
sdb: cache data unavailable
sdb: assuming drive cache: write through
sdb: unknown partition table
Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
----------------------------------------------------------
-----------------------------------------------------------
On Wed, 2005-10-05 at 16:50 +0200, Stephan Böni wrote:
> I've installed Xen 3.0-devel on SUSE Linux without any problems.
> But when i tryed to boot the system, i've got a funny problem:
>
> qla2300 0000:05:01.0: Found an ISP2312, irq 185, iobase 0xf8812000
> qla2300 0000:05:01.0: Configuring PCI space...
> qla2300 0000:05:01.0: Configure NVRAM parameters...
> qla2300 0000:05:01.0: Verifying loaded RISC code...
> qla2300 0000:05:01.0: Waiting for LIP to complete...
>
> until here all works fine, but then:
>
> input: PS/2 Generic Mouse on synaptcs-pt/serio0
> qla2300 0000:05:01.0: LIP reset occured (f7f7).
> qla2300 0000:05:01.0: LOOP UP detected (2 Gbps).
> qla2300 0000:05:01.0: Topology - (F_Port), Host Loop address 0xffff
> scsi3 : qla2xxx
> qla2300 0000:04:02.0:
> QLogic Fibre Channel HBA Driver: 8.01.00b5-k
> QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
> ISP2312: PCI-X (100 MHz) @ 0000:05:01.0 hdma+, host#=3,
> fw=3.03.15 IPX
> Loading kernel/fs/reiserfs/reiserfs.ko
> Waiting for device /dev/sda4 to appear: .....not found ---
> exiting to /bin/sh
> $
>
> if i use the standard (bigsmp) kernel the normal massages are:
>
> SCSI device sda: 41943040 512-byte hdwr sectors (21475 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 41943040 512-byte hdwr sectors (21475 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3 sda4
> ....usw.
>
> Well, my qla2300 has the storage attached not a generic mouse.
> Of course it isn't possible to boot from this mouse. :-(
>
> What's going wrong here?
>
> Stephan
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home