(XEN) Console output is synchronous. (XEN) xen image pstart: 0x4000000, xenheap pend: 0x8000000 (XEN) efi.trim_top: ignoring 4KB of memory at 0x0 due to granule hole at 0x0 (XEN) efi.trim_top: ignoring 636KB of memory at 0x1000 due to granule hole at 0x0 (XEN) efi.trim_bottom: ignoring 15360KB of memory at 0x100000 due to granule hole at 0x0 (XEN) ready to move Dom0 to 0x8000000 with len e31d70...ready to move initrd to 0x8e34000 with len 0...Done (XEN) find_memory: efi_memmap_walk returns max_page=9ffff (XEN) find_memory: last granule reserved for dom0; xen max_page=9f800 (XEN) Before heap_start: f000000004106a00 (XEN) After heap_start: f00000000411c000 (XEN) Init boot pages: 0x1000000 -> 0x4000000. (XEN) Init boot pages: 0x8000000 -> 0x3f5e4000. (XEN) Init boot pages: 0x3fb00000 -> 0x3fb2c000. (XEN) Init boot pages: 0x100000000 -> 0x27fffc000. (XEN) System RAM: 7142MB (7313456kB) (XEN) size of frame_table: 25520kB (XEN) alloc_dom0: starting (initializing 512 MB...) (XEN) alloc_dom0: dom0_start=0x8000000 (XEN) Xen heap: 62MB (64400kB) (XEN) About to call scheduler_init() (XEN) Using scheduler: Simple EDF Scheduler (sedf) (XEN) ACPI: RSDP (v002 HP ) @ 0x000000003fb2e000 (XEN) ACPI: XSDT (v001 HP zx6000 0x00000000 HP 0x00000000) @ 0x000000003fb2e02c (XEN) ACPI: FADT (v003 HP zx6000 0x00000000 HP 0x00000000) @ 0x000000003fb369e0 (XEN) ACPI: SPCR (v001 HP zx6000 0x00000000 HP 0x00000000) @ 0x000000003fb36b18 (XEN) ACPI: DBGP (v001 HP zx6000 0x00000000 HP 0x00000000) @ 0x000000003fb36b68 (XEN) ACPI: MADT (v001 HP zx6000 0x00000000 HP 0x00000000) @ 0x000000003fb36c28 (XEN) ACPI: SPMI (v004 HP zx6000 0x00000000 HP 0x00000000) @ 0x000000003fb36ba0 (XEN) ACPI: CPEP (v001 HP zx6000 0x00000000 HP 0x00000000) @ 0x000000003fb36bf0 (XEN) ACPI: SSDT (v001 HP zx6000 0x00000006 INTL 0x02012044) @ 0x000000003fb33870 (XEN) ACPI: SSDT (v001 HP zx6000 0x00000006 INTL 0x02012044) @ 0x000000003fb33a50 (XEN) ACPI: SSDT (v001 HP zx6000 0x00000006 INTL 0x02012044) @ 0x000000003fb33da0 (XEN) ACPI: SSDT (v001 HP zx6000 0x00000006 INTL 0x02012044) @ 0x000000003fb347c0 (XEN) ACPI: SSDT (v001 HP zx6000 0x00000006 INTL 0x02012044) @ 0x000000003fb351e0 (XEN) ACPI: SSDT (v001 HP zx6000 0x00000006 INTL 0x02012044) @ 0x000000003fb35c00 (XEN) ACPI: SSDT (v001 HP zx6000 0x00000006 INTL 0x02012044) @ 0x000000003fb36620 (XEN) ACPI: SSDT (v001 HP zx6000 0x00000006 INTL 0x02012044) @ 0x000000003fb36800 (XEN) ACPI: SSDT (v001 HP zx6000 0x00000006 INTL 0x02012044) @ 0x000000003fb368f0 (XEN) ACPI: DSDT (v001 HP zx6000 0x00000007 INTL 0x02012044) @ 0x0000000000000000 (XEN) SAL 3.1: HP version 2.31 (XEN) SAL Platform features: None (XEN) SAL: AP wakeup using external interrupt vector 0xff (XEN) No logical to physical processor mapping available (XEN) avail:0x1180c60000000000, status:0x60000000000,control:0x1180c00000000000, vm?0x0 (XEN) No VT feature supported. (XEN) cpu_init: current=f0000000040b4000, current->domain->arch.mm=0000000000000000 (XEN) vhpt_init: vhpt size=0x1000000, align=0x1000000 (XEN) vhpt_init: vhpt paddr=0x27d000000, end=0x27dffffff (XEN) ACPI: Local APIC address e8000000fee00000 (XEN) ACPI: LAPIC_ADDR_OVR (address[00000000fee00000]) (XEN) ACPI: LSAPIC (acpi_id[0x00] lsapic_id[0x00] lsapic_eid[0x00] enabled) (XEN) CPU 0 (0x0000) enabled (BSP) (XEN) ACPI: LSAPIC (acpi_id[0x01] lsapic_id[0x01] lsapic_eid[0x00] enabled) (XEN) CPU 1 (0x0100) enabled (XEN) ACPI: IOSAPIC (id[0x0] address[00000000fed20800] gsi_base[16]) (XEN) ACPI: IOSAPIC (id[0x1] address[00000000fed22800] gsi_base[27]) (XEN) ACPI: IOSAPIC (id[0x2] address[00000000fed24800] gsi_base[38]) (XEN) ACPI: IOSAPIC (id[0x3] address[00000000fed26800] gsi_base[49]) (XEN) ACPI: [APIC:0x06] ignored 3 entries of 7 found (XEN) 2 CPUs available, 2 CPUs total (XEN) ia64_mca_init() skipped (Machine check abort handling) (XEN) machine to physical table: 0xf000000004800000 mpt_table_size 0x4fc000 (XEN) mpt_order 9 max_page 0x9f800 (XEN) About to call init_xen_time() (XEN) CPU 0: base freq=200.000MHz, ITC ratio=13/2, ITC freq=1300.000MHz+/-650ppm (XEN) Time init: (XEN) .... System Time: 1561459ns (XEN) .... scale: C4EC4EC4 (XEN) About to call timer_init() (XEN) Boot processor id 0x0/0x0 (XEN) num_online_cpus=1, max_cpus=64 (XEN) cpu_init: current=f000000007ff0000, current->domain->arch.mm=0000000000000000 (XEN) vhpt_init: vhpt size=0x1000000, align=0x1000000 (XEN) vhpt_init: vhpt paddr=0x27c000000, end=0x27cffffff (XEN) CPU 1: synchronized ITC with CPU 0 (last diff -10 cycles, maxerr 573 cycles) (XEN) CPU 1: base freq=200.000MHz, ITC ratio=13/2, ITC freq=1300.000MHz+/-650ppm (XEN) Brought up 2 CPUs (XEN) Total of 2 processors activated (0.52 BogoMIPS). (XEN) About to call sort_main_extable() (XEN) About to call domain_create() (XEN) ###allocating rid_range, domain f00000000411cce0: starting_rid=40000, ending_rid=80000 (XEN) arch_domain_create: domain=f00000000411cce0 (XEN) About to call construct_dom0() (XEN) *** LOADING DOMAIN 0 *** (XEN) METAPHYSICAL MEMORY ARRANGEMENT: (XEN) Kernel image: 4000000->4f7d748 (XEN) Entry address: 400ff20 (XEN) Init. ramdisk: 0 len 0 (XEN) Start info.: 4f80000->4f84000 (XEN) Dom0 max_vcpus=1 (XEN) Dom0: 0xf00000000411cce0, domain: 0xf00000000411cce0 (XEN) Domain0 EFI passthrough:enable lsapic entry: 0xf00000003fb36c60 (XEN) DISABLE lsapic entry: 0xf00000003fb36c6c (XEN) ACPI 2.0=0x3fb2e000 SMBIOS=0x3fb3a000 HCDP=0x3fb2c000 (XEN) domain mem: type=2, attr=0x8, range=[0x0000000008000000-0x0000000008100000) (1MB) (XEN) domain mem: type=13, attr=0x8, range=[0x0000000008100000-0x0000000008200000) (1MB) (XEN) domain mem: type=7, attr=0x8, range=[0x0000000008200000-0x0000000027000000) (494MB) (XEN) domain mem: type=7, attr=0x8, range=[0x000000027e000000-0x000000027f000000) (16MB) (XEN) domain mem: type=12, attr=0x8000000000000001, range=[0x0003fffffc000000-0x0004000000000000) (64MB) (XEN) initrd start 0x27c00000 initrd size 0x0 (XEN) sync_split_caches ignored for CPU with no split cache (XEN) Scrubbing Free RAM: .......................................................................................................done. (XEN) About to call init_trace_bufs() (XEN) Xen trace buffers: disabled (XEN) About to call schedulers_start dom0=f00000000411cce0, idle_dom=f0000000040bbe08 (XEN) About to call startup_cpu_idle_loop() (XEN) vcpu_get_lrr0: Unmasked interrupts unsupported (XEN) vcpu_get_lrr1: Unmasked interrupts unsupported (XEN) Linux version 2.6.16-xen (awilliam@xenbuild) (gcc version 3.4.6 20060122 (prerelease) (Debian 3.4.5-2)) #1 SMP Sun Apr 9 09:05:11 MDT 2006 (XEN) EFI v1.00 by Xen/ia64: SALsystab=0x8000178 ACPI 2.0=0x3fb2e000 SMBIOS=0x3fb3a000 HCDP=0x3fb2c000 (XEN) warning: unable to switch EFI into virtual mode (status=9223372036854775811) (XEN) PCDP: v0 at 0x3fb2c000 (XEN) Explicit "console="; ignoring PCDP (XEN) Initial ramdisk at: 0xe000000027c00000 (0 bytes) (XEN) SAL 0.1: Xen/ia64 Xen/ia64 version 0.0 (XEN) **** vcpu_set_itv(65536): vitm=109c27bf6, setting to 0 (XEN) xen_pal_emulator: UNIMPLEMENTED PAL CALL 42!!!! (XEN) No logical to physical processor mapping available (XEN) vcpu_set_itc: Setting ar.itc is currently disabled (XEN) **** vcpu_set_itv(65536): vitm=0, setting to 0 (XEN) cpu_init: PAL VM summary failed, assuming 18 RID bits (XEN) ACPI: Local APIC address c0000000fee00000 (XEN) GSI 36 (level, low) -> CPU 0 (0x0000) vector 48 (XEN) 1 CPUs available, 2 CPUs total (XEN) *** CALLED SAL_SET_VECTORS. IGNORED... (XEN) SMP: Allowing 2 CPUs, 1 hotplug CPUs (XEN) Built 1 zonelists (XEN) Kernel command line: nomca root=/dev/sda2 xencons=ttyS8 console=ttyS8 ro (XEN) PID hash table entries: 4096 (order: 12, 131072 bytes) (XEN) Console: colour VGA+ 80x25 (XEN) Running on Xen! start_info_pfn=0x13e0 nr_pages=32768 flags=0x3 (XEN) xen-event-channel using irq 233 (XEN) Delivering first extint to domain: isr=0x0, iip=0xa0000001004d23f0 Dentry cache hash table entries: 2097152 (order: 10, 16777216 bytes) Inode-cache hash table entries: 1048576 (order: 9, 8388608 bytes) Placing software IO TLB between 0xcf80000 - 0x10f80000 Memory: 378976k/523264k available (10316k code, 143024k reserved, 4151k data, 288k init) McKinley Errata 9 workaround not needed; disabling it Mount-cache hash table entries: 1024 Boot processor id 0x0/0x0 Brought up 1 CPUs Total of 1 processors activated (1874.32 BogoMIPS). migration_cost=0 checking if image is initramfs... it is grant table at e000010000000000 Grant table initialized NET: Registered protocol family 16 ACPI: bus type pci registered ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOSAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) kernel unaligned access to 0xe00000027e9e3b84, ip=0xa00000010056c801 kernel unaligned access to 0xe00000027e9e3bb4, ip=0xa00000010056c801 kernel unaligned access to 0xe00000027e9e3bec, ip=0xa00000010056c801 kernel unaligned access to 0xe00000027e9e3c3c, ip=0xa00000010056c801 kernel unaligned access to 0xe00000027e9e3b7c, ip=0xa00000010056b601 ACPI: PCI Root Bridge [PCI1] (0000:20) (XEN) f+0ACPI: PCI Root Bridge [PCI2] (0000:40) ACPI: PCI Root Bridge [PCI3] (0000:60) ACPI: PCI Root Bridge [PCI4] (0000:80) ACPI: PCI Root Bridge [PCI6] (0000:c0) ACPI: PCI Root Bridge [PCI7] (0000:e0) SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub perfmon: version 2.0 IRQ 238 perfmon: Itanium 2 PMU detected, 16 PMCs, 18 PMDs, 4 counters (47 bits) PAL Information Facility v0.5 perfmon: added sampling format default_format perfmon_default_smpl: default_format v2.0 registered Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). SGI XFS with large block/inode numbers, no debug enabled Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered pci_hotplug: PCI Hot Plug PCI Core version: 0.5 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 radeonfb_pci_register BEGIN GSI 83 (level, low) -> CPU 0 (0x0000) vector 49 ACPI: PCI Interrupt 0000:e0:02.0[A] -> GSI 83 (level, low) -> IRQ 49 radeonfb (0000:e0:02.0): Found 16384k of DDR 64 bits wide videoram radeonfb (0000:e0:02.0): mapped 16384k videoram radeonfb: Found Intel x86 BIOS ROM Image radeonfb: Retrieved PLL infos from BIOS radeonfb: Reference=27.00 MHz (RefDiv=60) Memory=166.00 Mhz, System=166.00 MHz radeonfb: PLL min 12000 max 35000 1 chips in connector info - chip 1 has 2 connectors * connector 0 of type 2 (CRT) : 2300 * connector 1 of type 3 (DVI-I) : 3201 Starting monitor auto detection... radeonfb: I2C (port 1) ... not found radeonfb: I2C (port 2) ... not found radeonfb: I2C (port 3) ... found CRT display radeonfb: I2C (port 4) ... not found radeonfb: I2C (port 2) ... not found radeonfb: I2C (port 4) ... not found radeonfb: I2C (port 3) ... found CRT display radeonfb: Monitor 1 type CRT found radeonfb: EDID probed radeonfb: Monitor 2 type no found radeonfb (0000:e0:02.0): ATI Radeon QY radeonfb_pci_register END ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (FF) [SLPF] ACPI: Thermal Zone [THM0] (27 C) EFI Time Services Driver v0.4 Linux agpgart interface v0.101 (c) Dave Jones [drm] Initialized drm 1.0.1 20051102 i8042.c: No controller found. Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled GSI 34 (edge, high) -> CPU 0 (0x0000) vector 50 serial8250: ttyS0 at MMIO 0xff5e0000 (irq = 50) is a 16550A GSI 35 (edge, high) -> CPU 0 (0x0000) vector 51 serial8250: ttyS1 at MMIO 0xff5e2000 (irq = 51) is a 16550A GSI 82 (level, low) -> CPU 0 (0x0000) vector 52 ACPI: PCI Interrupt 0000:e0:01.0[A] -> GSI 82 (level, low) -> IRQ 52 0000:e0:01.0: ttyS2 at MMIO 0xf8051000 (irq = 52) is a 16550A ACPI: PCI Interrupt 0000:e0:01.1[A] -> GSI 82 (level, low) -> IRQ 52 0000:e0:01.1: ttyS3 at MMIO 0xf8050000 (irq = 52) is a 16550A Couldn't register serial port 0000:e0:01.1: -28 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) nbd: registered device at major 43 Intel(R) PRO/1000 Network Driver - version 6.3.9-k4 Copyright (c) 1999-2005 Intel Corporation. eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin and others GSI 20 (level, low) -> CPU 0 (0x0000) vector 53 ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 53 eth0: OEM i82557/i82558 10/100 Ethernet, 00:30:6E:1E:CE:5C, IRQ 53. Board assembly 000000-000, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. Secondary interface chip i82555. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0xb874c1d3). e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation tg3.c:v3.49 (Feb 2, 2006) GSI 29 (level, low) -> CPU 0 (0x0000) vector 54 ACPI: PCI Interrupt 0000:20:02.0[A] -> GSI 29 (level, low) -> IRQ 54 eth1: Tigon3 [partno(BCM95700A6) rev 0105 PHY(5701)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:30:6e:1e:de:2e eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] eth1: dma_rwctrl[76ff2d0f] dma_mask[64-bit] tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky arcnet: v3.93 BETA 2000/04/29 - by Avery Pennarun et al. netconsole: not configured, aborting Linux video capture interface: v1.00 Xen virtual console successfully installed as ttyS8 Event-channel device installed. blkif_init: reqs=64, pages=704, mmap_vstart=0xa000000200000000 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx CMD649: IDE controller at PCI slot 0000:00:02.0 GSI 21 (level, low) -> CPU 0 (0x0000) vector 55 ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 21 (level, low) -> IRQ 55 CMD649: chipset revision 2 CMD649: 100% native mode on irq 55 ide0: BM-DMA at 0x0d40-0x0d47, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x0d48-0x0d4f, BIOS settings: hdc:pio, hdd:pio hda: DV-28E-A, ATAPI CD/DVD-ROM drive ide0 at 0xd58-0xd5f,0xd66 on irq 55 hda: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide st: Version 20050830, fixed bufsize 32768, s/g segs 256 osst :I: Tape driver with OnStream support version 0.99.3 osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $ Fusion MPT base driver 3.03.07 Copyright (c) 1999-2005 LSI Logic Corporation Fusion MPT SPI Host driver 3.03.07 GSI 27 (level, low) -> CPU 0 (0x0000) vector 56 ACPI: PCI Interrupt 0000:20:01.0[A] -> GSI 27 (level, low) -> IRQ 56 mptbase: Initiating ioc0 bringup ioc0: 53C1030: Capabilities={Initiator,Target} scsi0 : ioc0: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=255, IRQ=56 Vendor: HP 73.4G Model: ST373207LC Rev: HPC1 Type: Direct-Access ANSI SCSI revision: 03 SCSI device sda: 143374738 512-byte hdwr sectors (73408 MB) sda: Write Protect is off SCSI device sda: drive cache: write through w/ FUA SCSI device sda: 143374738 512-byte hdwr sectors (73408 MB) sda: Write Protect is off SCSI device sda: drive cache: write through w/ FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 Vendor: HP 36.4G Model: MAS3367NC Rev: HPC3 Type: Direct-Access ANSI SCSI revision: 03 SCSI device sdb: 71132960 512-byte hdwr sectors (36420 MB) sdb: Write Protect is off SCSI device sdb: drive cache: write through w/ FUA SCSI device sdb: 71132960 512-byte hdwr sectors (36420 MB) sdb: Write Protect is off SCSI device sdb: drive cache: write through w/ FUA sdb: sdb1 sdb2 sdb3 sd 0:0:1:0: Attached scsi disk sdb sd 0:0:1:0: Attached scsi generic sg1 type 0 GSI 28 (level, low) -> CPU 0 (0x0000) vector 57 ACPI: PCI Interrupt 0000:20:01.1[B] -> GSI 28 (level, low) -> IRQ 57 mptbase: Initiating ioc1 bringup ioc1: 53C1030: Capabilities={Initiator,Target} scsi1 : ioc1: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=255, IRQ=57 Vendor: HP 73.4G Model: ST373207LC Rev: HPC1 Type: Direct-Access ANSI SCSI revision: 03 SCSI device sdc: 143374738 512-byte hdwr sectors (73408 MB) sdc: Write Protect is off SCSI device sdc: drive cache: write through w/ FUA SCSI device sdc: 143374738 512-byte hdwr sectors (73408 MB) sdc: Write Protect is off SCSI device sdc: drive cache: write through w/ FUA sdc: sdc1 sdc2 sdc3 sd 1:0:2:0: Attached scsi disk sdc sd 1:0:2:0: Attached scsi generic sg2 type 0 Fusion MPT SAS Host driver 3.03.07 usbmon: debugfs is not available GSI 18 (level, low) -> CPU 0 (0x0000) vector 58 ACPI: PCI Interrupt 0000:00:01.2[C] -> GSI 18 (level, low) -> IRQ 58 ehci_hcd 0000:00:01.2: EHCI Host Controller ehci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:01.2: irq 58, io mem 0x80021000 ehci_hcd 0000:00:01.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected GSI 16 (level, low) -> CPU 0 (0x0000) vector 59 ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 59 ohci_hcd 0000:00:01.0: OHCI Host Controller ohci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:01.0: irq 59, io mem 0x80023000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected GSI 17 (level, low) -> CPU 0 (0x0000) vector 60 ACPI: PCI Interrupt 0000:00:01.1[B] -> GSI 17 (level, low) -> IRQ 60 ohci_hcd 0000:00:01.1: OHCI Host Controller ohci_hcd 0000:00:01.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:01.1: irq 60, io mem 0x80022000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 2-2: new full speed USB device using ohci_hcd and address 2 usb 2-2: configuration #1 chosen from 1 choice USB Universal Host Controller Interface driver v2.3 Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver hiddev input: ATEN CS124U V1.00 as /class/input/input0 input: USB HID v1.00 Keyboard [ATEN CS124U V1.00] on usb-0000:00:01.0-2 input: ATEN CS124U V1.00 as /class/input/input1 input: USB HID v1.00 Mouse [ATEN CS124U V1.00] on usb-0000:00:01.0-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice i2c /dev entries driver device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@xxxxxxxxxx EFI Variables Facility v0.08 2004-May-17 efivars: get_next_variable: status=8000000000000003 Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC). no UART detected at 0x1 MTVAP IRQ 7 busy snd_mtpav: probe of snd_mtpav failed with error -16 specify port snd_mpu401: probe of snd_mpu401.0 failed with error -22 ALSA device list: #0: Dummy 1 #1: Virtual MIDI Card 1 NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 6, 1048576 bytes) TCP established hash table entries: 524288 (order: 9, 8388608 bytes) TCP bind hash table entries: 65536 (order: 6, 1048576 bytes) TCP: Hash tables configured (established 524288 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 288kB freed INIT: version 2.86 booting Mounting a tmpfs over /dev...done. Creating initial device nodes...done. Activating swap. Adding 2000768k swap on /dev/sda3. Priority:-1 extents:1 across:2000768k Checking root file system... fsck 1.37 (21-Mar-2005) Debian: clean, 436564/8699904 files, 2710860/17397216 blocks (check after next mount) EXT3 FS on sda2, internal journal System time was Sun Apr 9 15:20:35 UTC 2006. Setting the System Clock using the Hardware Clock as reference... System Clock set. System local time is now Sun Apr 9 15:20:37 UTC 2006. Cleaning up ifupdown...done. Not running depmod because /lib/modules/2.6.16-xen/ is not writeable. Loading modules... ide-cd FATAL: Could not load /lib/modules/2.6.16-xen/modules.dep: No such file or directory ide-disk FATAL: Could not load /lib/modules/2.6.16-xen/modules.dep: No such file or directory ide-generic FATAL: Could not load /lib/modules/2.6.16-xen/modules.dep: No such file or directory psmouse FATAL: Could not load /lib/modules/2.6.16-xen/modules.dep: No such file or directory sd_mod FATAL: Could not load /lib/modules/2.6.16-xen/modules.dep: No such file or directory All modules loaded. FATAL: Could not load /lib/modules/2.6.16-xen/modules.dep: No such file or directory Checking all file systems... fsck 1.37 (21-Mar-2005) Setting kernel variables ... ... done. Mounting local filesystems... Cleaning /tmp /var/run /var/lock. Detecting hardware: e100 tg3 cmd64x mptscsih usb_ohci ehci_hcd Skipping unavailable/built-in e100 module. Skipping unavailable/built-in tg3 module. Skipping unavailable/built-in cmd64x module. Skipping unavailable/built-in mptscsih module. Skipping unavailable/built-in ohci_hcd module. Skipping unavailable/built-in ehci_hcd module. Running 0dns-down to make sure resolv.conf is ok...done. Setting up networking...done. Starting hotplug subsystem: pci ignoring pci display device e0:02.0 pci [success] usb usb [success] isapnp isapnp [success] ide ide [success] input input [success] scsi FATAL: Could not load /lib/modules/2.6.16-xen/modules.dep: No such file or directory sd_mod: can't be loaded (for disk) FATAL: Could not load /lib/modules/2.6.16-xen/modules.dep: No such file or directory sd_mod: can't be loaded (for disk) FATAL: Could not load /lib/modules/2.6.16-xen/modules.dep: No such file or directory sd_mod: can't be loaded (for disk) scsi [success] done. Setting up IP spoofing protection: rp_filter. Configuring network interfaces...Internet Software Consortium DHCP Client 2.0pl5 Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium. All rights reserved. Please contribute if you find this software useful. For info, please visit http://www.isc.org/dhcp-contrib.html Listening on LPF/eth1/00:30:6e:1e:de:2e Sending on LPF/eth1/00:30:6e:1e:de:2e Sending on Socket/fallback/fallback-net DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 4 tg3: eth1: Link is up at 1000 Mbps, full duplex. tg3: eth1: Flow control is off for TX and off for RX. DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 10 DHCPOFFER from 10.0.0.1 DHCPREQUEST on eth1 to 255.255.255.255 port 67 DHCPACK from 10.0.0.1 bound to 10.91.73.11 -- renewal in 129600 seconds. done. Starting portmap daemon: portmap. Setting the System Clock using the Hardware Clock as reference... System Clock set. Local time: Sun Apr 9 09:20:58 MDT 2006 Initializing random number generator...done. Recovering nvi editor sessions... done. Setting up X server socket directory /tmp/.X11-unix...done. Setting up ICE socket directory /tmp/.ICE-unix...done. INIT: Entering runlevel: 2 Starting system log daemon: syslogd. Starting kernel log daemon: klogd. Starting portmap daemon: portmap. Starting MTA: exim4. Starting internet superserver: inetd. Starting printer spooler: lpd . Starting salinfo decode daemons: salinfo. Starting OpenBSD Secure Shell server: sshd. Starting NFS common utilities: statd. Starting deferred execution scheduler: atd. Starting periodic command scheduler: cron. Debian GNU/Linux 3.1 longs1 ttyS0 longs1 login: