On Sun, Mar 28, 2010 at 02:34:39PM +0300, Pasi Kärkkäinen wrote:
> On Sat, Mar 27, 2010 at 08:21:49PM -0700, Ritu kaur wrote:
> > I tried another thing. After compilation, I did "make modules_install"
> > in
> > xcp ddk in order to use following command
> >
> > mkinitrd -f ./initrd-2.6.32.img 2.6.32
> >
> > I get following errors...
> >
> > modinfo: could not find module ide-disk
> > No module ide-disk found for kernel 2.6.32, aborting
> >
>
> mkinitrd reads /etc/modprobe.conf to figure out what modules should be
> included into the initrd image.
>
also I'm not sure if ide-disk is a required module for 2.6.32?
-- Pasi
> > My boot disk is ide and looking into .config didn't give me any ideas as
> > to what has to be enabled.
> >
>
> If you need some other module then fix it in /etc/modprobe.conf
> You need to figure out what's the correct driver for your root/boot disk.
>
> -- Pasi
>
> > Thanks
> >
> > On Sat, Mar 27, 2010 at 6:32 PM, Ritu kaur <[1]ritu.kaur.us@[2]gmail.com>
> > wrote:
> >
> > Thanks Pasi. I had used following command to regenerate initrd image in
> > xcp ddk
> >
> > mkinitrd -f ./initrd-2.6.32.img 2.6.27.42-0.1.1.xs0.1.1.737.1065xen
> >
> > it doesn't work either. While booting screen goes blank immediately
> > after I see
> > ...
> > Booting:MBI=0x00010120, entry=0x00100000
> >
> > and next thing I see is BIOS setup, so not sure connecting serial cable
> > will reveal anything more. Inputs appreciated.
> >
> > Thanks
> >
> > On Sat, Mar 27, 2010 at 11:43 AM, Pasi Kärkkäinen <[3]pasik@xxxxxx>
> > wrote:
> >
> > On Sat, Mar 27, 2010 at 11:28:12AM -0700, Ritu kaur wrote:
> > > Any inputs on this? I compiled xen/next kernel in Debian Lenny
> > and booted
> > > successfully as a domU(I am using same .config file which I used
> > to build
> > > under xcp-ddk). Looks to me xen/next doesn't work with xcp0.1.1.
> > >
> >
> > You need to re-generate the dom0 kernel initrd to match your kernel.
> > You cannot use the default xcp initrd image.
> >
> > Please provide the full serial console boot log so we can
> > troubleshoot
> > it:
> > [4]http://wiki.xensource.com/xenwiki/XenSerialConsole
> >
> > -- Pasi
> >
> > > Thanks
> > >
> > > On Fri, Mar 26, 2010 at 12:11 PM, Ritu kaur
> > <[1][5]ritu.kaur.us@[2][6]gmail.com>
> > > wrote:
> > >
> > > Hi Pasi,
> > >
> > > Messages seen with not-working case
> > >
> > >
> >
> > /***********************************************************************************
> > > kernel:/boot/xen.3.4.3.gz dom0-mem=752M
> > lowmem-emergency-pool=1M
> > > crashkernel=64M@32M console=comX vga=mode-0x0311
> > > loading /boot/xen.3.4.3.gz..........
> > > Module:/boot/vmlinuz-2.6.32 root=LABEL=root-mhycetek ro
> > Xencons=hvc
> > > console=hvc0 console=tty0 quiet vga=785 splash
> > > Loading /boot/vmlinuz-2.6.32.........
> > > Module:/boot/initrd-2.6-xen.img
> > > Loading
> > >
> >
> > /boot/initrd-2.6-xen.img...............................................................................................
> > > Booting:MBI=0x00010120, entry=0x00100000
> > >
> >
> > ***************************************************************************************/
> > >
> > > Screen is blank after these messages and system returns to
> > BIOS
> > setup.
> > >
> > > Messages seen with working case
> > >
> >
> > /***********************************************************************************
> > > kernel:/boot/xen.gz dom0-mem=752M lowmem-emergency-pool=1M
> > > crashkernel=64M@32M comsole=comX vga=mode-0x0311
> > > loading /boot/xen.gz..........
> > > Module:/boot/vmlinuz-2.6.xen root=LABEL=root-mhycetek ro
> > Xencons=hvc
> > > console=hvc0 console=tty0 quiet vga=785 splash
> > > Loading /boot/vmlinuz-2.6.xen.........
> > > Module:/boot/initrd-2.6-xen.img
> > > Loading
> > >
> >
> > /boot/initrd-2.6-xen.img...............................................................................................
> > > Booting:MBI=0x00010120, entry=0x00100000
> > >
> >
> > ***************************************************************************************/
> > >
> > > Versions used in Non-working case
> > >
> > > xen - 3.4.3/4.0.0
> > > kernel - xen/next
> > > initrd - default one which came with xcp0.1.1 download.(Ps
> > note, in xcp
> > > ddk cannot build initrd image)
> > >
> > > in Working case
> > >
> > > xen - 3.4.2
> > > kernel - xcp 0.1.1
> > > initrd - one that came with xcp 0.1.1
> > >
> > > Checked in my .config and changed CONFIG_PHYSICAL_START to
> > 0x00100000
> > > and CONFIG_PHYSICAL_ALIGN=0x100000, didn't help.
> > >
> > > Inputs appreciated.
> > >
> > > Thanks
> > >
> > > References
> > >
> > > Visible links
> > > 1. [7]http://ritu.kaur.us/
> > > 2. [8]http://gmail.com/
> >
> > > _______________________________________________
> > > Xen-devel mailing list
> > > [9]Xen-devel@xxxxxxxxxxxxxxxxxxx
> > > [10]http://lists.xensource.com/xen-devel
> >
> > References
> >
> > Visible links
> > 1. http://ritu.kaur.us/
> > 2. http://gmail.com/
> > 3. mailto:pasik@xxxxxx
> > 4. http://wiki.xensource.com/xenwiki/XenSerialConsole
> > 5. http://ritu.kaur.us/
> > 6. http://gmail.com/
> > 7. http://ritu.kaur.us/
> > 8. http://gmail.com/
> > 9. mailto:Xen-devel@xxxxxxxxxxxxxxxxxxx
> > 10. http://lists.xensource.com/xen-devel
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home