> before a login prompt (when xend is starting I think)
>
> Note that I have NOT bisected tools, just the hypervisor
> so the crashes are likely due to a newer xend failing on
> an older hypervisor (which is irrelevant to this problem).
I realized I just had to disable xend to test this and it
confirmed my hypothesis.
So 20072 boots fine without max_cstate=2, while 20073
fails to boot unless max_cstate=2 is a Xen boot parameter.
> -----Original Message-----
> From: Dan Magenheimer
> Sent: Tuesday, December 08, 2009 4:25 PM
> To: Dan Magenheimer; Yu, Ke; Xen-Devel (E-mail)
> Cc: xiantao.zhang@xxxxxxxxx
> Subject: RE: latest xen-unstable fails to boot on Dell D630 (likely
> hpet/Cstate problem)
>
>
> > But I'll give bisecting a try.
>
> Looks like the problem has been around for awhile. It appears
> the problem starts at c/s 20073. Xiantao cc'ed since 20073
> was his patch.
>
> 20070 boots OK without max_cstate=2
>
> 20072 boots most of the way without max_cstate=2 but crashes
> before a login prompt (when xend is starting I think)
>
> 20073 FAILS to boot without max_cstate=2 but crashes
> before a login prompt
>
> 20082 FAILS to boot without max_cstate=2 but crashes
> before a login prompt with max_cstate=2
>
> 20143 FAILS to boot without max_cstate=2 but boots OK
> with max_cstate=2
>
> Note that I have NOT bisected tools, just the hypervisor
> so the crashes are likely due to a newer xend failing on
> an older hypervisor (which is irrelevant to this problem).
>
> > -----Original Message-----
> > From: Dan Magenheimer
> > Sent: Tuesday, December 08, 2009 10:42 AM
> > To: Yu, Ke; Xen-Devel (E-mail)
> > Subject: RE: latest xen-unstable fails to boot on Dell D630 (likely
> > hpet/Cstate problem)
> >
> >
> > > case, if convenient, could you help to do some bisect to see
> > > which cset cause this bug?
> >
> > I can do this, but because it is often no longer easy to
> > bisect Xen because of interdependencies with other
> > components, I was hoping that Keir or you or someone might
> > have some idea of what changeset might have caused the regression.
> > But I'll give bisecting a try.
> >
> > > max_cstate=2), when dom0 hangs, is xen still alive, E.g. can
> > > Xen response to three Ctrl-'A' in serial?
> >
> > Unfortunately, I can't seem to get a Xen console working on
> > the Merom machine, and the problem can't be reproduced on
> > my other machine where the Xen console is working (because
> > Conroe doesn't support deep C).
> >
> > > -----Original Message-----
> > > From: Yu, Ke [mailto:ke.yu@xxxxxxxxx]
> > > Sent: Tuesday, December 08, 2009 12:08 AM
> > > To: Dan Magenheimer; Xen-Devel (E-mail)
> > > Subject: RE: latest xen-unstable fails to boot on Dell
> D630 (likely
> > > hpet/Cstate problem)
> > >
> > >
> > > >-----Original Message-----
> > > >In this thread, I observed that I was unable to
> > > >provoke deep C state (C3) on my Dell D630, which has
> > > >a Intel Merom (dual-core laptop) processor. At that
> > > >time, when I tried enabling hpetbroadcast, dom0 boot failed.
> > > >
> > > >http://lists.xensource.com/archives/html/xen-devel/2009-10/ms
> > > g01027.html
> > > >
> > > >As it turned out, all RHEL5-based (maybe RHEL4- also) dom0
> > > >default installation run /sbin/hwclock, which IIRC takes
> > > >the RTC away from Xen and gives it to dom0. Since the
> > > >Xen hpet emulation does not do RTC emulation, bad things
> > > >then happen when a deep Cstate is entered (dom0 apparently
> > > >never wakes up). I think Ke Yu has also reproduced this problem.
> > > >
> > > >Sometime in the last few weeks, some patch in xen-unstable
> > > >apparently changed some defaults and xen-unstable will
> > > >no longer boot with this processor/dom0, with or without
> > > >hpetbroadcast on the Xen command line. However, specifying
> > > >max_cstate=2 on the Xen command line allows a successful
> > > >dom0 boot, so I suspect the problem is the same (or at
> > > >least very similar).
> > > >
> > > >I did a quick scan for hpet changes and found c/s 20497,
> > > >but backing it out made no difference.
> > > >
> > > >I have a workaround for now, but since it is likely that
> > > >many customers (including all of Oracle's OVS customers)
> > > >use a RHEL5-based dom0 boot sequence, and Merom processors
> > > >work fine otherwise, it would be nice to get this identified
> > > >and fixed before 4.0.
> > >
> > > Let's firstly figure out which component the issue resides.
> > >
> > > Firstly, in the default boot (i.e. without specifying
> > > max_cstate=2), when dom0 hangs, is xen still alive, E.g. can
> > > Xen response to three Ctrl-'A' in serial?
> > >
> > > If only dom0 hangs, it is probably that RTC malfunction make
> > > incorrect dom0 time and lead dom0 fail to boot. Then RTC
> > > emulation in hypervisor should fix this issue.
> > >
> > > If Xen also hangs, it should be another bug, i.e. hpet
> > > broadcast does not wake up CPU in deep C states. in this
> > > case, if convenient, could you help to do some bisect to see
> > > which cset cause this bug?
> > >
> > > Best Regards
> > > Ke
> > >
> > >
> >
>
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home