Hi
Weidong,
Thanks for your
replies...
I now have Windows XP
DomU with Primary VGA , USB Keyboard + Mouse Passthrough. I am using
2.6.30-rc3 pvops with netbk vif.
Primary VGA is Nvidia
Geforce GTX260
The DomU has
hangs/locks with any graphics intensive operations, i.e. Opening Internet
Explorer on the MSN homepage makes DomU freeze !!
I noticed in the
attached qemu log that the some of the memory addresses are not the same as
the lspci output:
pt_register_regions: IO
region registered (size=0x01000000
base_addr=0xb6000000)
pt_register_regions: IO
region registered (size=0x10000000
base_addr=0xe000000c)
pt_register_regions: IO
region registered (size=0x02000000
base_addr=0xb4000004)
02:00.0 VGA compatible
controller: nVidia Corporation GT200 [GeForce GTX 260] (rev a1) (prog-if 00
[VGA controller])
Subsystem: nVidia Corporation Device 068e
Flags: bus master, fast devsel, latency 0, IRQ 11
[virtual] Memory at b6000000 (32-bit, non-prefetchable)
[size=16M]
Memory at e0000000 (64-bit, prefetchable)
[size=256M]
Memory at b4000000 (64-bit, non-prefetchable)
[size=32M]
I/O ports at 3000 [size=128]
Is this expected
?
Would you have any
idea why this would be so unstable / crash ?
Also, the Mouse is
passthrough using usbdevice=”host:##:##”, but has a really bad lag/delay on
refresh .. can this be helped ?
Cheers,
Tim
Tim,
See my
comments belew.
From: Tim
Moore [mailto:timothy.moore@xxxxxxxxxxx]
Sent: 2009年9月3日
17:03
To: Han, Weidong
Cc: 'enming.teo@xxxxxxxxxxxxxxx'; djmagee@xxxxxxxxxxxx; xen-devel@xxxxxxxxxxxxxxxxxxx
Subject:
RE: [Xen-devel] RE: xen-unstable pci passthrough
Hi
Weidong,
Thank you for all
your hard work ;)
I have just
successfully passed through my Nvidia Geforce GTX260 as a fully functional
card to my WinXP DomU !!!!!
My findings so
far:
1) Tried with my 9500
GT (Secondary card) which DOES load the driver successfully but NO output on
the Monitor (VGA is sized correctly but monitor is
OFF)
2) GTX260 (Primary
card) (Dom0 boot VGA) starting DomU from remote SSH console, VGA Loads and
Display works !!!!
In both cases I am
using the NVidia binary driver in the WinXP DomU.
The 9500GT (Secondary
card) passthrough still has issues, the driver loads without the Monitor
displaying anything (DPMS?) and if I make ANY changes to the DomU Graphics
then the DomU locks up hard.
[Weidong]:
I didn't try 9500GT. Seems it needs extra hacks.
In both cases the VGA
card only works the FIRST time, I.e. FLR is required to reset the card for
re-use, display become corrupt on second boot of DomU. Restart Dom0 and the
VGA will work again the first time DomU is started.
[Weidong]: Yes,
it's not reset well. I suspect it's still in graphics mode, so cannot
display the boot messages in VGA mode. In my experiments,
WinXP guest can still boot into graphics mode, although you
cannot see booting progress.
Is there anyway we
can impletement the d3r, sbr or flr functionality that is in XCI? I would
like to see if a sbr will enable to Card to be reset.
[Weidong]:
these reset functions are already in xen-unstable, but no one can
really reset gfx. In my feeling, it needs vendor specific method
to reset it.
I would also like to
debug the issue with Secondary passthrough as it seems that this is nearly
there too ...
Regards,
Tim
Dear
Magee,
Any
luck with the Intel vga passthrough patches to xen 3.5-unstable on Intel
DQ45CB with extra PCI-e x16 graphics card? Are you using pvops dom 0 kernels
2.6.30-rc3 and 2.6.31-rc6?
Regards,
Mr. Teo En Ming
(Zhang Enming) Dip(Mechatronics Engineering) BEng(Hons)(Mechanical
Engineering)
Technical Support
Engineer
Information
Technology Department
Asiasoft Online Pte Ltd
Tampines Central 1
#04-01 Tampines Plaza
Singapore 529541
That was
the problem, thank you. Now I’ll work on testing the gfx-passthrough
patches.
I
suspect you are using old hvm config file. The device_model is changes in
config file.
in old
config file:
# New
stuff
device_model = '/usr/' + arch_libdir +
'/xen/bin/qemu-dm'
in new
config file:
# Device
Model to be used
device_model = 'qemu-dm'
Pls
check it, and use the latest config file to create guest.
Regards,
Weidong
From: xen-devel-bounces@xxxxxxxxxxxxxxxxxxx [mailto:xen-devel-bounces@xxxxxxxxxxxxxxxxxxx]
On Behalf Of djmagee@xxxxxxxxxxxx
Sent:
2009年9月2日
6:40
To: xen-devel@xxxxxxxxxxxxxxxxxxx
Subject:
[Xen-devel] xen-unstable pci passthrough
I have not been able to passthrough any
PCI devices using the latest xen-unstable. I have a DQ45CB, and have
successfully passed devices to guests using 3.4.1.
The latest c/s in my copy of
xen-unstable is 20145. I just started playing around with unstable
yesterday, so I can’t tell you if earlier revisions worked. I’ve tried
with various dom0 kernels, the current 2.6.18.8-xen branch, a xenified
2.6.29.6, and a pvops 2.6.31-rc6, and in every case I get the same
error. I’ve tried both putting pci= in the config file, and hot-adding
the device using xm pci-attach. In every case, the xm command (either
create or pci-attach) fails with the message “Error: Timed out waiting for
device model action”. The guests in every case are HVM guests, some
flavors of Windows, as well as the Knoppix 5.3.1 DVD.
The relevant xm dmesg output
is:
(XEN) PCI add device 00:1b.0
(XEN) [VT-D]iommu.c:1292:d0
domain_context_unmap:PCIe: bdf = 0:1b.0
(XEN) [VT-D]iommu.c:1178:d0
domain_context_mapping:PCIe: bdf = 0:1b.0
(XEN) [VT-D]io.c:284:d0 VT-d irq bind:
m_irq = 37 device = 3 intx = 0
(XEN) [VT-D]iommu.c:1292:d0
domain_context_unmap:PCIe: bdf = 0:1b.0
(XEN) [VT-D]iommu.c:1178:d0
domain_context_mapping:PCIe: bdf = 0:1b.0
And the messages from
qemu-log:
dm-command: hot insert pass-through pci
dev
hot add pci slot -2
exceed.
Please let me know what else I need to
supply to help resolve this problem. If I need to enable debugging
messages, let me know the best way to do this.
Doug Magee
djmagee@xxxxxxxxxxxx
No virus
found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.409 / Virus Database:
270.13.75/2340 - Release Date: 09/01/09 20:03:00
Home