Teo,
See below ...
Tim
From: Teo En Ming (Zhang Enming)
[mailto:enming.teo@xxxxxxxxxxxxxxx]
Sent: 03 September 2009 10:15
To: Tim Moore; 'Han, Weidong'
Cc: djmagee@xxxxxxxxxxxx; xen-devel@xxxxxxxxxxxxxxxxxxx
Subject: RE: [Xen-devel] RE: xen-unstable pci passthrough
Hi Tim,
Are you using xen 3.5-unstable? YES
Which changeset are you using? (no
clue at the moment, was the one that v1 patches apply to)
What Intel gfx passthrough patches are you using? (all)
1.
xen-gfx-passthrough.patch
YES
2.
qemu-gfx-passthrough.patch
YES
3.
xen-load-vbios-file.patch
YES
4.
xen-vbar-pbar.patch
YES
5.
qemu-vbar-pbar.patch
YES
6.
secondary-gfx-passthrough.patch
YES
7. revert MMIO
allocation back to 0xf0000000 (examine the patches, it's obvious)
How do you apply the patches and compile xen and tools?
1) Applied the v1 patches
to relevant changeset (I've not updated my HG repo since v2 patches released)
2) Amended memory addresses as Weidong Han recommended for
Secondary or Primary VGA as appropriate
3) Run "make"
on the hvmloader
4) Run "make
install-tools" on xen-unstable
Don't forget to
reboot Dom0 after every attempt at assigning card to DomU, the card needs resetting
to work each time.
What pvops dom 0 kernel are you using?
both 2.6.30-rc6 and
2.6.18-xen works for me
When I do a “xm list”, I see win xp domU running. But I am always
shown a QEMU monitor and couldn’t proceed any further on the matter.
I also get QEMU Monitor in vncviewer, this is because Cirrus VGA
is not loaded. You should have VGA on your passthrough card, if not you will
need vncviewer in the DomU (which will only be accessible when WinXP has booted
successfully)
Regards,
Mr. Teo En Ming (Zhang
Enming) Dip(Mechatronics Engineering) BEng(Hons)(Mechanical Engineering)
Technical Support
Engineer
Information Technology
Department
Asiasoft Online Pte Ltd
Tampines Central 1 #04-01 Tampines Plaza
Singapore 529541
Republic of Singapore
Mobile: +65-9648-9798
MSN: teoenming@xxxxxxxxxxx
From: Tim Moore
[mailto:timothy.moore@xxxxxxxxxxx]
Sent: Thursday, September 03, 2009 5:03 PM
To: 'Han, Weidong'
Cc: 'enming.teo@xxxxxxxxxxxxxxx'; djmagee@xxxxxxxxxxxx;
xen-devel@xxxxxxxxxxxxxxxxxxx
Subject: RE: [Xen-devel] RE: xen-unstable pci passthrough
Hi Weidong,
Thank you for all your hard work
;)
I have just successfully passed
through my Nvidia Geforce GTX260 as a fully functional card to my WinXP DomU
!!!!!
My findings so far:
1) Tried with my 9500 GT
(Secondary card) which DOES load the driver successfully but NO output on the
Monitor (VGA is sized correctly but monitor is OFF)
2) GTX260 (Primary card) (Dom0
boot VGA) starting DomU from remote SSH console, VGA Loads and Display works
!!!!
In both cases I am using the
NVidia binary driver in the WinXP DomU.
The 9500GT (Secondary card)
passthrough still has issues, the driver loads without the Monitor displaying
anything (DPMS?) and if I make ANY changes to the DomU Graphics then the DomU
locks up hard.
In both cases the VGA card only
works the FIRST time, I.e. FLR is required to reset the card for re-use,
display become corrupt on second boot of DomU. Restart Dom0 and the VGA will
work again the first time DomU is started.
Is there anyway we can impletement
the d3r, sbr or flr functionality that is in XCI? I would like to see if a sbr
will enable to Card to be reset.
I would also like to debug the
issue with Secondary passthrough as it seems that this is nearly there too ...
Regards,
Tim
From: xen-devel-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Teo En Ming
(Zhang Enming)
Sent: 03 September 2009 05:12
To: djmagee@xxxxxxxxxxxx; 'Han, Weidong'; xen-devel@xxxxxxxxxxxxxxxxxxx
Subject: RE: [Xen-devel] RE: xen-unstable pci passthrough
Dear Magee,
Any luck with the Intel vga passthrough patches to xen 3.5-unstable
on Intel DQ45CB with extra PCI-e x16 graphics card? Are you using pvops dom 0
kernels 2.6.30-rc3 and 2.6.31-rc6?
Regards,
Mr. Teo En Ming (Zhang
Enming) Dip(Mechatronics Engineering) BEng(Hons)(Mechanical Engineering)
Technical Support
Engineer
Information Technology
Department
Asiasoft Online Pte Ltd
Tampines Central 1 #04-01 Tampines Plaza
Singapore 529541
Republic of Singapore
Mobile: +65-9648-9798
MSN: teoenming@xxxxxxxxxxx
From: xen-devel-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of djmagee@xxxxxxxxxxxx
Sent: Wednesday, September 02, 2009 6:59 PM
To: Han, Weidong; xen-devel@xxxxxxxxxxxxxxxxxxx
Subject: RE: [Xen-devel] RE: xen-unstable pci passthrough
That was the problem,
thank you. Now I’ll work on testing the gfx-passthrough patches.
From: xen-devel-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Han, Weidong
Sent: Tuesday, September 01, 2009 6:55 PM
To: djmagee@xxxxxxxxxxxx; 'xen-devel@xxxxxxxxxxxxxxxxxxx'
Subject: [Xen-devel] RE: xen-unstable pci passthrough
I suspect you are using old hvm config file. The device_model is
changes in config file.
in old config file:
# New stuff
device_model = '/usr/' + arch_libdir + '/xen/bin/qemu-dm'
in new config file:
# Device Model to be used
device_model = 'qemu-dm'
Pls check it, and use the latest config file to create guest.
Regards,
Weidong
From:
xen-devel-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of djmagee@xxxxxxxxxxxx
Sent: 2009年9月2日 6:40
To: xen-devel@xxxxxxxxxxxxxxxxxxx
Subject: [Xen-devel] xen-unstable pci passthrough
I have not been able to passthrough any PCI
devices using the latest xen-unstable. I have a DQ45CB, and have
successfully passed devices to guests using 3.4.1.
The latest c/s in my copy of xen-unstable
is 20145. I just started playing around with unstable yesterday, so I
can’t tell you if earlier revisions worked. I’ve tried with various dom0
kernels, the current 2.6.18.8-xen branch, a xenified 2.6.29.6, and a pvops
2.6.31-rc6, and in every case I get the same error. I’ve tried both
putting pci= in the config file, and hot-adding the device using xm
pci-attach. In every case, the xm command (either create or pci-attach)
fails with the message “Error: Timed out waiting for device model
action”. The guests in every case are HVM guests, some flavors of
Windows, as well as the Knoppix 5.3.1 DVD.
The relevant xm dmesg output is:
(XEN) PCI add device 00:1b.0
(XEN) [VT-D]iommu.c:1292:d0
domain_context_unmap:PCIe: bdf = 0:1b.0
(XEN) [VT-D]iommu.c:1178:d0
domain_context_mapping:PCIe: bdf = 0:1b.0
(XEN) [VT-D]io.c:284:d0 VT-d irq bind:
m_irq = 37 device = 3 intx = 0
(XEN) [VT-D]iommu.c:1292:d0
domain_context_unmap:PCIe: bdf = 0:1b.0
(XEN) [VT-D]iommu.c:1178:d0
domain_context_mapping:PCIe: bdf = 0:1b.0
And the messages from qemu-log:
dm-command: hot insert pass-through pci dev
hot add pci slot -2 exceed.
Please let me know what else I need to
supply to help resolve this problem. If I need to enable debugging
messages, let me know the best way to do this.
Doug Magee
djmagee@xxxxxxxxxxxx
No virus
found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.409 / Virus Database: 270.13.75/2340 - Release Date: 09/01/09
20:03:00
No virus
found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.409 / Virus Database: 270.13.75/2340 - Release Date: 09/01/09
20:03:00
Home