| |
|
 |
|
 |
|
|
|
| |
|
|
xen-devel
RE: [Xen-devel] FC-HBA assigned to guest domain does not work.
I'm also suffering from the issue: the assigned FC-HBA (rev 03) doesn't work.
But I don't see the iommu fault in your mail.
Serial messages don't give any special info in my case.
In my case, the issue looks like a regression. For example, "Xen 16711 + Dom0
417" can work while the latest xen-unstable doesn't work.
I can only access the host remotely and it died... I'll continue to look into
the issue next week.
-- Dexuan
-----Original Message-----
From: xen-devel-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Yuji Shimada
Sent: 2008年8月29日 16:05
To: xen-devel@xxxxxxxxxxxxxxxxxxx
Subject: [Xen-devel] FC-HBA assigned to guest domain does not work.
I assigned FC-HBA to guest domain, but it did not work.
FC-HBA seems to write its internal memory which is mapped to host
memory space via pci transaction. But there is no mapping in IOMMU's
page table, so that page fault occurs in IOMMU.
I think that MMIO resource mapped via p2m table should be mapped via
IOMMU's page table too. In other word, XEN_DOMCTL_memory_mapping
hypercall should update not only p2m table, but also IOMMU's page table.
What do you think about this?
Does anyone see the same issue?
/var/log/message on guest linux:
Aug 28 11:53:28 localhost kernel: Emulex LightPulse Fibre Channel SCSI driver
8.2.0.22
Aug 28 11:53:28 localhost kernel: Copyright(c) 2004-2008 Emulex. All rights
reserved.
Aug 28 11:53:28 localhost kernel: GSI 16 sharing vector 0xA9 and IRQ 16
Aug 28 11:53:28 localhost kernel: ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI
40(level, low) -> IRQ 169
Aug 28 11:53:28 localhost kernel: scsi0 : on PCI bus 00 device 30 irq 169
Aug 28 11:53:28 localhost kernel: lpfc 0000:00:06.0: 0:0453 Adapter failed to
init, mbxCmd xb READ_CONFIG, mbxStatus x0
Aug 28 11:53:28 localhost kernel: ACPI: PCI interrupt for device 0000:00:06.0
disabled
lspci output on guest linux:
00:06.0 Fibre Channel: Emulex Corporation Zephyr LightPulse Fibre Channel Host
Adapter (rev 02)
Subsystem: Emulex Corporation Zephyr LightPulse Fibre Channel Host
Adapter
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Interrupt: pin A routed to IRQ 169
Region 0: Memory at f3041000 (64-bit, non-prefetchable) [disabled]
[size=4K]
^^^^^^^^
Region 2: Memory at f3042000 (64-bit, non-prefetchable) [disabled]
[size=4K]
Region 4: I/O ports at c100 [disabled] [size=256]
Expansion ROM at f3000000 [disabled] [size=256K]
xm dmesg output on dom0 linux:
(XEN) [VT-D]iommu.c:775: iommu_page_fault: iommu->reg = ffff828bfff58000
(XEN) [VT-D]iommu.c:747: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:729: iommu_fault:DMA Write: 7:0.0 addr f3041000 REASON 5
^^^^^^^^
iommu->reg = ffff828bfff58000
(XEN) print_vtd_entries: iommu = ffff8300d6e01780 bdf = 7:0:0 gmfn = f3041
(XEN) root_entry = ffff83021fdf2000
(XEN) root_entry[7] = 217de9001
(XEN) context = ffff830217de9000
(XEN) context[0] = 201_2155d1001
(XEN) l3 = ffff8302155d1000
(XEN) l3_index = 3
(XEN) l3[3] = 1d802a003
(XEN) l2 = ffff8301d802a000
(XEN) l2_index = 198
(XEN) l2[198] = 0
(XEN) l2[198] not present
Thanks,
--
Yuji Shimada
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
|
|
| |
|
Home