[Xen-devel] Re: [patch 14/21] Xen-paravirt: Add XEN config options and disable unsupported config options.

[Dan Hecht <dhecht@xxxxxxxxxx>]

On 02/13/2007 02:17 PM, Jeremy Fitzhardinge wrote:
> The XEN config option enables the Xen paravirt_ops interface, which is
> installed when the kernel finds itself running under Xen. (By some
> as-yet fully defined mechanism, implemented in a future patch.)
>
> Xen is no longer a sub-architecture, so the X86_XEN subarch config
> option has gone.
>
> The disabled config options are:
> - PREEMPT: Xen doesn't support it
> - HZ: set to 100Hz for now, to cut down on VCPU context switch rate.
>   This will be adapted to use tickless later.
> - kexec: not yet supported
I assume you plan to eventually get all this stuff working but just want 
to prevent configurations that the Xen paravirt-ops isn't ready for at 
the moment?
Instead can you do it this way:

config XEN
    depends on PARAVIRT && !PREEMPT && HZ_100 && !DOUBLEFAULT && !KEXEC


thanks,
Dan


> Signed-off-by: Jeremy Fitzhardinge <jeremy@xxxxxxxxxxxxx>
> Signed-off-by: Ian Pratt <ian.pratt@xxxxxxxxxxxxx>
> Signed-off-by: Christian Limpach <Christian.Limpach@xxxxxxxxxxxx>
> Signed-off-by: Chris Wright <chrisw@xxxxxxxxxxxx>
>
> ---
>  arch/i386/Kconfig       |    7 +++++--
>  arch/i386/Kconfig.debug |    1 +
>  arch/i386/xen/Kconfig   |   10 ++++++++++
>  kernel/Kconfig.hz       |    4 ++--
>  kernel/Kconfig.preempt  |    1 +
>  5 files changed, 19 insertions(+), 4 deletions(-)
>
> ===================================================================
> --- a/arch/i386/Kconfig
> +++ b/arch/i386/Kconfig
> @@ -192,6 +192,8 @@ config PARAVIRT
>           under a hypervisor, improving performance significantly.
>           However, when run without a hypervisor the kernel is
>           theoretically slower.  If in doubt, say N.
> +
> +source "arch/i386/xen/Kconfig"
>  
>  config ACPI_SRAT
>         bool
> @@ -298,12 +300,12 @@ config X86_UP_IOAPIC
>  
>  config X86_LOCAL_APIC
>         bool
> -       depends on X86_UP_APIC || ((X86_VISWS || SMP) && !X86_VOYAGER) || 
> X86_GENERICARCH
> +       depends on X86_UP_APIC || (((X86_VISWS || SMP) && !X86_VOYAGER) || 
> X86_GENERICARCH)
>         default y
>  
>  config X86_IO_APIC
>         bool
> -       depends on X86_UP_IOAPIC || (SMP && !(X86_VISWS || X86_VOYAGER)) || 
> X86_GENERICARCH
> +       depends on X86_UP_IOAPIC || ((SMP && !(X86_VISWS || X86_VOYAGER)) || 
> X86_GENERICARCH)
>         default y
>  
>  config X86_VISWS_APIC
> @@ -743,6 +745,7 @@ source kernel/Kconfig.hz
>  
>  config KEXEC
>         bool "kexec system call"
> +       depends on !XEN
>         help
>           kexec is a system call that implements the ability to shutdown your
>           current kernel, and to start another kernel.  It is like a reboot
> ===================================================================
> --- a/arch/i386/Kconfig.debug
> +++ b/arch/i386/Kconfig.debug
> @@ -79,6 +79,7 @@ config DOUBLEFAULT
>  config DOUBLEFAULT
>         default y
>         bool "Enable doublefault exception handler" if EMBEDDED
> +       depends on !XEN
>         help
>            This option allows trapping of rare doublefault exceptions that
>            would otherwise cause a system to silently reboot. Disabling this
> ===================================================================
> --- /dev/null
> +++ b/arch/i386/xen/Kconfig
> @@ -0,0 +1,10 @@
> +#
> +# This Kconfig describes xen options
> +#
> +
> +config XEN
> +       bool "Enable support for Xen hypervisor"
> +       depends PARAVIRT
> +       default y
> +       help
> +         This is the Linux Xen port.
> ===================================================================
> --- a/kernel/Kconfig.hz
> +++ b/kernel/Kconfig.hz
> @@ -3,7 +3,7 @@
>  #
>  
>  choice
> -       prompt "Timer frequency"
> +       prompt "Timer frequency" if !XEN
>         default HZ_250
>         help
>          Allows the configuration of the timer frequency. It is customary
> @@ -49,7 +49,7 @@ endchoice
>  
>  config HZ
>         int
> -       default 100 if HZ_100
> +       default 100 if HZ_100 || XEN
>         default 250 if HZ_250
>         default 300 if HZ_300
>         default 1000 if HZ_1000
> ===================================================================
> --- a/kernel/Kconfig.preempt
> +++ b/kernel/Kconfig.preempt
> @@ -35,6 +35,7 @@ config PREEMPT_VOLUNTARY
>  
>  config PREEMPT
>         bool "Preemptible Kernel (Low-Latency Desktop)"
> +       depends on !XEN
>         help
>           This option reduces the latency of the kernel by making
>           all kernel code (that is not executing in a critical section)
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel