Hello,
After searching the archives, I've found only two messages regarding
this case, but there were no solution.
I have a similar problem, so I try to ask here.
I have twi HFC chipset ISDN cards in my pc:
0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network
controller [HFC-PCI] (rev 02)
Subsystem: Cologne Chip Designs GmbH ISDN Board
Flags: bus master, medium devsel, latency 16, IRQ 11
I/O ports at b800 [disabled] [size=8]
Memory at de800000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
0000:00:0e.0 Network controller: Cologne Chip Designs GmbH ISDN network
controller [HFC-PCI] (rev 02)
Subsystem: Cologne Chip Designs GmbH ISDN Board
Flags: bus master, medium devsel, latency 16, IRQ 3
I/O ports at b400 [disabled] [size=8]
Memory at de000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
Note that "I/O ports at b400 [disabled]". Why is it disabled?
I've downloaded the bristuff driver, and compiled it with "make
ARCH=xen". The driver installs correctly, finds the cards, but when I
issue the ztcfg command, the domain crashes immidiatly:
Zapata Telephony Interface Registered on major 196
PCI: Enabling device 0000:00:0d.0 (0006 -> 0007)
PCI: Obtained IRQ 11 for device 0000:00:0d.0
zaphfc: CCD/Billion/Asuscom 2BD0 configured at mem 0xd08b2000 fifo
0xcf048000(0x3b292000) IRQ 11 HZ 100
zaphfc: Card 0 configured for TE mode
PCI: Enabling device 0000:00:0e.0 (0006 -> 0007)
PCI: Obtained IRQ 3 for device 0000:00:0e.0
zaphfc: CCD/Billion/Asuscom 2BD0 configured at mem 0xd08be000 fifo
0xcf068000(0x3b272000) IRQ 3 HZ 100
zaphfc: Card 1 configured for TE mode
zaphfc: 2 hfc-pci card(s) in this box.
testvm:~# lsmod
Module Size Used by
zaphfc 13076 0
zaptel 227332 1 zaphfc
crc_ccitt 1728 1 zaptel
tulip 50144 0
testvm:~# free
total used free shared buffers cached
Mem: 256128 27088 229040 0 4252 10720
-/+ buffers/cache: 12116 244012
Swap: 1048568 0 1048568
testvm:~# ztcfg
Registered tone zone 3 (Netherlands)
testvm:~# zaphfc: bchan rx fifo not enough bytes to receive! (z1=0, z2=0,
wanted 8 got 0), probably a buffer overrun.
zaphfc: bchan rx fifo not enough bytes to receive! (z1=0, z2=0, wanted 8 got
0), probably a buffer overrun.
************ REMOTE CONSOLE EXITED *****************
The kernel is a 2.6.11.7 with the patches from 2.0-testing xen source. Xen
itself is 2.0.5 stable. Can it cause the problem?
The kernel is configured as a privileged guest, based on the dom0 config.
Here's the config of this vm:
kernel = "/boot/xen/xen-linux-2.6.11-xenu-priv"
memory = 256
name = "testvm"
nics = 1
ip = "192.168.1.10"
gateway = "192.168.1.254"
hostname = "testvm"
disk = [ 'phy:vg00/testvm,sda1,w', 'phy:vg00/testvmpv,sdb1,w' ]
root = "/dev/sda1"
restart = "onreboot"
pci = [ '0,0d,0', '0,0e,0', '0,0f,0' ]
Regards,
Krisztian Czako
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home