# HG changeset patch
# User Keir Fraser <keir.fraser@xxxxxxxxxx>
# Date 1224241225 -3600
# Node ID 50aaffd8f87c7dd085cc02bf471f1e4d1155dd11
# Parent 6bf61b830153010d9f3a551811469a7fbfddf023
Enable PCI serial devices for console messages
The basic issue is that some PCI serial devices use a non-standard
crystal to control the baud rate divisor. This patch enhances the
`com' parameter to enable you to specify the crystal frequency used by
the serial device. Since this parameter already allows you to specify
I/O address and IRQ this is all that is needed to get a PCI serial
device to work. With this patch the `com' parameter is now defined
as:
comN=BBB[/CCC][,NPS[,III[,IRQ]]]
Where `CCC' is the crystal frequency. Note that if you specify 0 for
`IRQ' Xen will run the serial device in polled mode, obviating the
need for interrupts (an advantage since this is the only way I was
able to get my PCI serial device to work).
As an example, I am using the xen boot command:
kernel /xen.gz com1=3D115200,8n1,0xe880/921600,0
console=3Dcom1
Signed-off-by: Don Dugger <donald.d.dugger@xxxxxxxxx>
Signed-off-by: Keir Fraser <keir.fraser@xxxxxxxxxx>
---
xen/drivers/char/ns16550.c | 19 ++++++++++++++-----
1 files changed, 14 insertions(+), 5 deletions(-)
diff -r 6bf61b830153 -r 50aaffd8f87c xen/drivers/char/ns16550.c
--- a/xen/drivers/char/ns16550.c Thu Oct 16 18:45:48 2008 +0100
+++ b/xen/drivers/char/ns16550.c Fri Oct 17 12:00:25 2008 +0100
@@ -18,17 +18,19 @@
#include <asm/io.h>
/*
- * Configure serial port with a string <baud>,DPS,<io-base>,<irq>.
+ * Configure serial port with a string:
+ * <baud>[/<clock_hz>][,DPS[,<io-base>[,<irq>]]].
* The tail of the string can be omitted if platform defaults are sufficient.
* If the baud rate is pre-configured, perhaps by a bootloader, then 'auto'
- * can be specified in place of a numeric baud rate.
+ * can be specified in place of a numeric baud rate. Polled mode is specified
+ * by requesting irq 0.
*/
static char opt_com1[30] = "", opt_com2[30] = "";
string_param("com1", opt_com1);
string_param("com2", opt_com2);
static struct ns16550 {
- int baud, data_bits, parity, stop_bits, irq;
+ int baud, clock_hz, data_bits, parity, stop_bits, irq;
unsigned long io_base; /* I/O port or memory-mapped I/O address. */
char *remapped_io_base; /* Remapped virtual address of mmap I/O. */
/* UART with IRQ line: interrupt-driven I/O. */
@@ -192,7 +194,7 @@ static void __devinit ns16550_init_preir
if ( uart->baud != BAUD_AUTO )
{
/* Baud rate specified: program it into the divisor latch. */
- divisor = UART_CLOCK_HZ / (uart->baud * 16);
+ divisor = uart->clock_hz / (uart->baud << 4);
ns_write_reg(uart, DLL, (char)divisor);
ns_write_reg(uart, DLM, (char)(divisor >> 8));
}
@@ -201,7 +203,7 @@ static void __devinit ns16550_init_preir
/* Baud rate already set: read it out from the divisor latch. */
divisor = ns_read_reg(uart, DLL);
divisor |= ns_read_reg(uart, DLM) << 8;
- uart->baud = UART_CLOCK_HZ / (divisor * 16);
+ uart->baud = uart->clock_hz / (divisor << 4);
}
ns_write_reg(uart, LCR, lcr);
@@ -354,6 +356,12 @@ static void __init ns16550_parse_port_co
}
else if ( (baud = simple_strtoul(conf, &conf, 10)) != 0 )
uart->baud = baud;
+
+ if ( *conf == '/')
+ {
+ conf++;
+ uart->clock_hz = simple_strtoul(conf, &conf, 0) << 4;
+ }
if ( *conf != ',' )
goto config_parsed;
@@ -408,6 +416,7 @@ void __init ns16550_init(int index, stru
uart->baud = (defaults->baud ? :
console_has((index == 0) ? "com1" : "com2")
? BAUD_AUTO : 0);
+ uart->clock_hz = UART_CLOCK_HZ;
uart->data_bits = defaults->data_bits;
uart->parity = parse_parity_char(defaults->parity);
uart->stop_bits = defaults->stop_bits;
_______________________________________________
Xen-changelog mailing list
Xen-changelog@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-changelog
|
Home