[Xen-users] Failed to setup NAT network

To:	xen-users@xxxxxxxxxxxxxxxxxxx
Subject:	[Xen-users] Failed to setup NAT network
From:	YAO <yffbrave@xxxxxxxxx>
Date:	Fri, 17 Jun 2011 20:32:44 +0800
Delivery-date:	Fri, 17 Jun 2011 05:34:06 -0700
Dkim-signature:	v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=gamma; h=domainkey-signature:mime-version:date:message-id:subject:from:to :content-type; bh=JQla3k9hC6xmkM45E1KA5mM3PIX7jUMASJ8wlWGEMF4=; b=renWUvfEW7JEcCKtLPsu2hf/8hgL4PDRRBEUfPw2+Svm/GZLq6dJBI43UfPTQjRLtO ht/a88VMIoCzIwQYvI+2gaG5lQTZHRaiuazIUbL/lA1lSkX0/FllhLA4E5ZSepLRC7Fk Ozci/mjWdSMZFXiU3UsEjlPnPmTmucTV+NNa4=
Domainkey-signature:	a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=mime-version:date:message-id:subject:from:to:content-type; b=vcWYkg3YPlOcLFqKMDk3D5I9w0ea1xHI9E/tYhSOwN3lt0PhbbUjvmFVLDBd6TZqt8 CHIGVI/9qtG6w9x9cXFDY1nXHnEskRYz0Fh1B9QQnqn7zTB86kE2RJSdBM4MqhabVIsk 3qtzeTh4GUlq9QTx6bjHmCjSMaMHh7vrd0qbE=
Envelope-to:	www-data@xxxxxxxxxxxxxxxxxxx
List-help:	<mailto:xen-users-request@lists.xensource.com?subject=help>
List-id:	Xen user discussion <xen-users.lists.xensource.com>
List-post:	<mailto:xen-users@lists.xensource.com>
List-subscribe:	<http://lists.xensource.com/mailman/listinfo/xen-users>, <mailto:xen-users-request@lists.xensource.com?subject=subscribe>
List-unsubscribe:	<http://lists.xensource.com/mailman/listinfo/xen-users>, <mailto:xen-users-request@lists.xensource.com?subject=unsubscribe>
Sender:	xen-users-bounces@xxxxxxxxxxxxxxxxxxx

I'm using Xen 4.1 and here's what I did:

1.comment network-script and vif-script about bridge in /etc/xen/xend-config.sxp, uncomment the lines about nat

2.set vm config, add something like vif = [ 'mac=00:16:3e:00:00:11, ip=10.0.0.1' ]

3.set /etc/network/interfaces in domU, add lines as follows:

auto eth0

iface eth0 inet static

address 10.0.0.1

gateway 10.0.0.254

netmask 255.255.255.0

But it didn't work!

Here's the output of "ifconfig -a" in dom0

tap10.0 Link encap:Ethernet HWaddr a6:8a:1b:92:be:af

BROADCAST MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:500

RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

vif10.0 Link encap:Ethernet HWaddr fe:ff:ff:ff:ff:ff

BROADCAST MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:32

RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

the vif10.0 didn't get an ip!

The same thing happened in domU whose eth0 didn't get ip, too. Strangely, eth0 was renamed to eth9, I don't know why.

So, where did I make mistake? How to setup NAT network in the new toolstack?

By the way, can I use bridge mode if I have only one IP?

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

WARNING - OLD ARCHIVES