Re: [Xen-users] PV networking issue in 2.6.38.6 and 2.6.39-rc7

[Mario <mario@xxxxxxxxxxxxxx>]

As far as getting 2.6.38.6 running as dom0, few moments ago I have just 
made a working version by patched it with gentoo rebased patches, and so 
far everything runs nicely :-)
But this means all in-kernel xen code is probably replaced with stuff 
from those patches..
On 05/15/2011 06:24 PM, Erwan RENIER wrote:
> I did the test too with vanilla kernel a while ago and ran into the same
> problem, thought i didn't search it out.
> Instead i used the konrad xen kernel wich is 2.6.38-8 and works fine (
> almost ^^ ).
> I suppose he made adjustment on the network stack and it should be good
> to check the diffs with the vanilla kernel to find out.
>
> git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen.git
>
>
> Le 15/05/2011 18:12, Pasi Kärkkäinen a écrit :
> > On Sun, May 15, 2011 at 06:02:02PM +0200, Mario wrote:
> > > On 05/15/2011 05:53 PM, Pasi Kärkkäinen wrote:
> > > > On Sun, May 15, 2011 at 02:36:11PM +0200, Mario wrote:
> > > > > Hey everyone,
> > > > >
> > > > > I have been trying to make Xen-4.1.0 work on kernels mentioned in the
> > > > > subject, without much sucess. HVM guests are not affected, only PV.
> > > > Below you mention gentoo xenlinux patches..
> > > >
> > > > So please be more specific about which kernel was vanilla (pvops),
> > > > and which kernels had some external patches applied..
> > > >
> > > > -- Pasi
> > > Sorry, both kernels in subject were vanilla from kernel.org, with xen
> > > options selected for dom0 usage.
> > > I only wanted to point out that networking works if i use kernel patched
> > > with rebased gentoo patches.
> > > I am talking only about dom0 kernel here, domU kernel does not seem to
> > > be the source of the problem.
> > OK. What kernel is the PV domU running? What Xen version are you
> > using? 4.1 ?
> >
> > -- Pasi
> >
> > > > > Error that i see in dmesg on the domU:
> > > > > XENBUS: Timeout connecting to device: device/vif/0 (state 1)
> > > > >
> > > > > ifconfig -a on domU shows MAC address: 00:00:00:00:00:00
> > > > >
> > > > > dom0 doesn't have any vif/tap interfaces assigned to domU when i do
> > > > > brctl show or ifconfig -a
> > > > >
> > > > > I don't see any errors worth mentioning in /var/log/xen, except mybe
> > > > > these two:
> > > > >
> > > > > /tmp/SBo/xen-4.1.0/tools/ioemu-qemu-xen/hw/xen_blktap.c:628: Init
> > > > > blktap
> > > > > pipes
> > > > > Could not open /var/run/tap/qemu-read-2
> > > > >
> > > > > Problem goes away when i boot 2.6.34.7 (it is the last kernel that i
> > > > > have built with gentoo rebased patches).
> > > > >
> > > > > If there is something i can do to help debug this please do let me
> > > > > know.
> > > > >
> > > > >
> > > > > Best regards,
> > > > > mario
> > > > >
> > > > > _______________________________________________
> > > > > Xen-users mailing list
> > > > > Xen-users@xxxxxxxxxxxxxxxxxxx
> > > > > http://lists.xensource.com/xen-users
> > > > _______________________________________________
> > > > Xen-users mailing list
> > > > Xen-users@xxxxxxxxxxxxxxxxxxx
> > > > http://lists.xensource.com/xen-users
> > _______________________________________________
> > Xen-users mailing list
> > Xen-users@xxxxxxxxxxxxxxxxxxx
> > http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users