Re: [Xen-users] XCP networking

To:	rvegas <robertvegas@xxxxxxxxxxx>
Subject:	Re: [Xen-users] XCP networking
From:	Todd Deshane <todd.deshane@xxxxxxx>
Date:	Sat, 19 Feb 2011 00:57:20 +0000
Cc:	xen-users@xxxxxxxxxxxxxxxxxxx
Delivery-date:	Fri, 18 Feb 2011 16:59:30 -0800
Dkim-signature:	v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=gamma; h=domainkey-signature:mime-version:sender:in-reply-to:references:from :date:x-google-sender-auth:message-id:subject:to:cc:content-type; bh=AW3GxYRGYTATMDWL4IlEOlvsfj06og/1Zv0CP7rdzhw=; b=M1oh16s90/QACsC4oXTv7MNgdbeAD6FXBdRtTCZzhlKr2DvSKDHn8qceTfd6HU7WNo M/f6eA56LOxUYiOZ4IoKii97CpyeyXLLI/yJ5Gy4CkEplBafimM1fESBzEKpbUh+b+AV Jc4k5IvVj2sgOMX2hBudCQu0b3h3C2AJQx9Z8=
Domainkey-signature:	a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=mime-version:sender:in-reply-to:references:from:date :x-google-sender-auth:message-id:subject:to:cc:content-type; b=igkw9AYUKJskwfPxmNC/R5uL/l5wmzZg9hLbWwAwjNaAw4kvsByAvpvfMMm1sY6agz AoSKPcxR2uGXKRRYJZELHL/L1gEC3dSBtQuzqFWKguaeyjK4t6F8ojZBCJui5o/kb9nL AIr1q27r/2mrURDRaQsLpduxMCPPph56vEisI=
Envelope-to:	www-data@xxxxxxxxxxxxxxxxxxx
In-reply-to:	<1298058355176-3391691.post@xxxxxxxxxxxxx>
List-help:	<mailto:xen-users-request@lists.xensource.com?subject=help>
List-id:	Xen user discussion <xen-users.lists.xensource.com>
List-post:	<mailto:xen-users@lists.xensource.com>
List-subscribe:	<http://lists.xensource.com/mailman/listinfo/xen-users>, <mailto:xen-users-request@lists.xensource.com?subject=subscribe>
List-unsubscribe:	<http://lists.xensource.com/mailman/listinfo/xen-users>, <mailto:xen-users-request@lists.xensource.com?subject=unsubscribe>
References:	<1298058355176-3391691.post@xxxxxxxxxxxxx>
Sender:	xen-users-bounces@xxxxxxxxxxxxxxxxxxx

On Fri, Feb 18, 2011 at 7:45 PM, rvegas <robertvegas@xxxxxxxxxxx> wrote:
>
> I have setup XCP on 2 X hp bl460c blades within a c7000 enclosure. The
> enclosure cisco 3020 switch has a trunk setup to a cisco 6500.
> reading through the docs it says that xcp will use a virtual switch and
> vlans. i'm a bit confused on how to setup the nic of the actual blade.
> the only option i have is to set it up as an access port. which means that
> its part of only one vlan.
>
> vm1 --- vswitch= vlan 12
> vm2 --- vswitch= vlan 14
>
> blade nic0 = vlan 12
>
> enclosure trunk vlan 12, 14
>
> so with the setup above, only packets from vm1 will get forwarded. i guess
> this is more of a cisco question.


from: http://support.citrix.com/article/CTX123489
"Configuring the XenServer management interface on a VLAN network is
not supported"

So be sure to use a different nic (not the management one) for your vlan stuff.

Creating vlans:
http://docs.vmd.citrix.com/XenServer/5.6.0fp1/1.0/en_gb/reference.html#networking-standalone_host_config-vlans

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

WARNING - OLD ARCHIVES

xen-users

Re: [Xen-users] XCP networking