Add this to the xen.gz line
kernel /boot/xen.gz-2.6.18-194.32.1.el5 console=com1,tty com1=115200,8n1
dom0_mem=4000000
Steve
On Sun, 6 Feb 2011, Bill M wrote:
Thanks for the note, Steve. Here is my grub.conf:
default=0
timeout=5
serial --unit=0 --speed=115200 --dumb
terminal --timeout=5 serial console
title Xen-CentOS (Xen-3.4.1, vmlinuz-2.6.18.8-xen)
root (hd0,1)
kernel /boot/xen.gz
module /boot/vmlinuz-2.6.18.8-xen ro
root=UUID=c25415f0-1eff-4b3e-a03b-99c3fecbbe57 console=tty0
console=ttyS0,115200 selinux=0
module /boot/initrd-2.6.18.8-xen.img
title CentOS (2.6.18-194.8.1.el5)
root (hd0,1)
kernel /boot/vmlinuz-2.6.18-194.8.1.el5 ro
root=UUID=c25415f0-1eff-4b3e-a03b-99c3fecbbe57 console=tty0
console=ttyS0,115200 selinux=0
initrd /boot/initrd-2.6.18-194.8.1.el5.img
I think I have included the serial console on the module line for
dom0(console=ttyS0,115200), but please correct me if I'm wrong on this. I
tried to add "console=tty0 console=ttyS0,115200" to the line of "kernel
/boot/xen.gz", but still no output from the hypervisor.
You made a good point that 2.6.18-8 kernel is indeed quite old, and may not
support the hardware on R710. Actually, I don't really mind which version of
Xen I should use for my setup. I tried the stock Xen(the rpm is 3.0.3) on
CentOS 5.5(with yum groupinstall), but still got the same result. Is there
any option I should add to the kernel line to get some output from the
hypervisor? so far I have tried "watchdog sync_console" but none is working.
Bill
On Sat, Feb 5, 2011 at 8:31 PM, Steven Timm <timm@xxxxxxxx> wrote:
How is your grub.conf set up.. it may be that there are other
errors that are visible only on the serial console and not on tty0.
2.6.18-8 is a pretty old kernel for R710 architecture. the redhat/centos
built kernel with centos 5.5 allows for new hardware architectures like
Nehalem which the source that comes in 2.6.18-8 kernel might not.
I am running the stock xen and kernel that come with Sci.Linux 5.5
(another RH clone) which as others have mentioned is 3.1.2 even though
the rpm says 3.0.3. Are there some 3.4 features that you need
that aren't in the stock xen/kernel.
Steve Timm
On Sat, 5 Feb 2011, Bill M wrote:
Hi,
I'm trying to get Xen 3.4.1 working on CentOS 5.5(64bit) for a Dell R710
box(Quad Core Xeon "Nehalem" processor, 12 GB Memory and 2 Seagate SATA
HDD).
I followed the README to make world, make install, generate the
corresponding ram disk with initrd, and modified /boot/menu.lst. I believe
I
didn't make any mistake through these steps, because I was able to get Xen
3.4.1 running on CentOS 5.5 for a Dell Optiplex 745 box (Intel Core 2 Duo
E6600, 2GB memory and 1 SATA HDD) with the same procedure.
However, for the R710 box, once I reboot the server and boot with Xen, the
system enters a halt that lasts forever, and all I got on the console was
this:
--------------------------------
Booting command-list
root (hd0,1)
Filesystem type is ext2fs, partition type 0x83
kernel /boot/xen.gz
[Multiboot-elf, <0x100000:0x11f770:0x6b890>, shtab=0x28b078,
entry=0x100000]
module /boot/vmlinuz-2.6.18.8-xen ro
root=UUID=c25415f0-1eff-4b3e-a03b-99c3fecb
be57 console=tty0 console=ttyS0,115200 selinux=0
[Multiboot-module @ 0x28c000, 0x73b340 bytes]
module /boot/initrd-2.6.18.8-xen.img
[Multiboot-module @ 0x9c8000, 0x48ebc00 bytes]
--------------------------------
No error message at all... So my guess is that the system halts right
after
the grub loading. But, has the hypervisor booted? what causes the halt?
I have tried three different ways to get Xen working on my R710 setup, but
they all ended up with the same bizarre output.
1) Building from source for Xen 3.4.3, Xen 3.3.2, Xen 3.1.4;
2) Using yum to install binary for Xen 3.4.3, Xen 3.0.3 (the stock Xen
comes
with CentOS 5.5) (I came across a post here mentioning someone
successfully
get Xen 3.0.3 (CentOS 5.4) running on R710).
3) Building linux-2.6.18.8-xen with the existing CentOS kernel
configuration
file. I copied the existing configuration file into
the build-linux-2.6.18-xen_x86_64 directory and followed the README on how
to build the kernel with .config under the build-linux-2.6.18-xen_x86_64
directory. For all remaining configure questions during compiling, I chose
the default option.
Up to this point, I'm totally clueless on how to solve this problem. Has
anyone seen this problem before, or any insight to share? I would really
appreciate the help.
Thanks,
--
Bill
--
------------------------------------------------------------------
Steven C. Timm, Ph.D (630) 840-8525
timm@xxxxxxxx http://home.fnal.gov/~timm/
Fermilab Computing Division, Scientific Computing Facilities,
Grid Facilities Department, FermiGrid Services Group, Group Leader.
Lead of FermiCloud project.
--
------------------------------------------------------------------
Steven C. Timm, Ph.D (630) 840-8525
timm@xxxxxxxx http://home.fnal.gov/~timm/
Fermilab Computing Division, Scientific Computing Facilities,
Grid Facilities Department, FermiGrid Services Group, Group Leader.
Lead of FermiCloud project.
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home