> >
>
> Hello,
>
> I see that your Dom0 has 33543988k #32GB, is it all the memory in the
> server?
> If so it is possible that after some "ballooning" and memory allocation
> the memory is too unorganized that the allocator can't find suitable
> chunks of memory. I had had that problem after a system upgrade where
> the "menu.lst" (or grub.fcg) was recreated without the tuning
> parameters.
> I think that 32GB is fa too much for the Dom0, usually Dom0 is limited
> to a value between 1024M and 3072M with the dom0_mem=xxxx in the
> grub.cfg, the memory of Dom0 is mainly used for buffer cache on behalf
> of the Domus.
> It is also often useful to use the parameter "dom0_min_mem=xxx" in the
> xend.config file. In my systems I use the same value eg :
> (dom0-min-mem 2048)
> (enable-dom0-ballooning no)
> in xend-config.sxo
> and
> multiboot /xen-3.4.gz /xen-3.4.gz noreboot dom0_mem=2048M
> in grub.cfg.
> I have had problems with "ballonning yes" if domUs are stopped and
> started many times without a server reboot (memory fargmentation ?).
>
> Regards
>
> JP Pozzi
No, dom0 has 4gb (was lower but was trying 4gb to see if it helped)
dom0_min_mem is set to 512M
Ballooning is disabled.
>From menu.lst:
###Don't change this comment - YaST2 identifier: Original name: xen###
title Xen -- SUSE Linux Enterprise Server 11 - 2.6.27.19-5
root (hd0,1)
kernel /boot/xen.gz dom0_mem=4096M
module /boot/vmlinuz-2.6.27.19-5-xen
root=/dev/disk/by-id/scsi-200d0b29d2d004400-part2
resume=/dev/disk/by-id/scsi-200d0b29d2d004400-part1 splash=silent showopts
vga=0x317
module /boot/initrd-2.6.27.19-5-xen
See xen-config.sxp below.
Thanks,
James
# cat xend-config.sxp
# -*- sh -*-
#
# Xend configuration file.
#
# This example configuration is appropriate for an installation that
# utilizes a bridged network configuration. Access to xend via http
# is disabled.
# Commented out entries show the default for that entry, unless otherwise
# specified.
#(logfile /var/log/xen/xend.log)
#(loglevel DEBUG)
# Uncomment the line below. Set the value to flask, acm, or dummy to
# select a security module.
#(xsm_module_name dummy)
# The Xen-API server configuration.
#
# This value configures the ports, interfaces, and access controls for the
# Xen-API server. Each entry in the list starts with either unix, a port
# number, or an address:port pair. If this is "unix", then a UDP socket is
# opened, and this entry applies to that. If it is a port, then Xend will
# listen on all interfaces on that TCP port, and if it is an address:port
# pair, then Xend will listen on the specified port, using the interface with
# the specified address.
#
# The subsequent string configures the user-based access control for the
# listener in question. This can be one of "none" or "pam", indicating either
# that users should be allowed access unconditionally, or that the local
# Pluggable Authentication Modules configuration should be used. If this
# string is missing or empty, then "pam" is used.
#
# The final string gives the host-based access control for that listener. If
# this is missing or empty, then all connections are accepted. Otherwise,
# this should be a space-separated sequence of regular expressions; any host
# with a fully-qualified domain name or an IP address that matches one of
# these regular expressions will be accepted.
#
# Example: listen on TCP port 9363 on all interfaces, accepting connections
# only from machines in example.com or localhost, and allow access through
# the unix domain socket unconditionally:
#
# (xen-api-server ((9363 pam '^localhost$ example\\.com$')
# (unix none)))
#
# Optionally, the TCP Xen-API server can use SSL by specifying the private
# key and certificate location:
#
# (9367 pam '' /etc/xen/xen-api.key /etc/xen/xen-api.crt)
#
# Default:
# (xen-api-server ((unix)))
#(xend-http-server no)
(xend-unix-server yes)
#(xend-tcp-xmlrpc-server no)
#(xend-unix-xmlrpc-server yes)
# Only enable xend-relocation-server on trusted networks as it lacks
# encryption and authentication.
#(xend-relocation-server no)
#(xend-relocation-ssl-server no)
#(xend-udev-event-server no)
#(xend-unix-path /var/lib/xend/xend-socket)
# Address and port xend should use for the legacy TCP XMLRPC interface,
# if xend-tcp-xmlrpc-server is set.
#(xend-tcp-xmlrpc-server-address 'localhost')
#(xend-tcp-xmlrpc-server-port 8006)
# SSL key and certificate to use for the legacy TCP XMLRPC interface.
# Setting these will mean that this port serves only SSL connections as
# opposed to plaintext ones.
#(xend-tcp-xmlrpc-server-ssl-key-file /etc/xen/xmlrpc.key)
#(xend-tcp-xmlrpc-server-ssl-cert-file /etc/xen/xmlrpc.crt)
# Port xend should use for the HTTP interface, if xend-http-server is set.
#(xend-port 8000)
# Port xend should use for the relocation interface, if xend-relocation-server
# is set.
#(xend-relocation-port 8002)
# Port xend should use for the ssl relocation interface, if
# xend-relocation-ssl-server is set.
#(xend-relocation-ssl-port 8003)
# SSL key and certificate to use for the ssl relocation interface, if
# xend-relocation-ssl-server is set.
#(xend-relocation-server-ssl-key-file /etc/xen/xmlrpc.key)
#(xend-relocation-server-ssl-cert-file /etc/xen/xmlrpc.crt)
# Whether to use ssl as default when relocating.
#(xend-relocation-ssl no)
# Address xend should listen on for HTTP connections, if xend-http-server is
# set.
# Specifying 'localhost' prevents remote connections.
# Specifying the empty string '' (the default) allows all connections.
#(xend-address '')
#(xend-address localhost)
# Address xend should listen on for relocation-socket connections, if
# xend-relocation-server is set.
# Meaning and default as for xend-address above.
#(xend-relocation-address '')
# The hosts allowed to talk to the relocation port. If this is empty (the
# default), then all connections are allowed (assuming that the connection
# arrives on a port and interface on which we are listening; see
# xend-relocation-port and xend-relocation-address above). Otherwise, this
# should be a space-separated sequence of regular expressions. Any host with
# a fully-qualified domain name or an IP address that matches one of these
# regular expressions will be accepted.
#
# For example:
# (xend-relocation-hosts-allow '^localhost$ ^.*\\.example\\.org$')
#
#(xend-relocation-hosts-allow '')
(xend-relocation-hosts-allow '^localhost$ ^localhost\\.localdomain$')
# The limit (in kilobytes) on the size of the console buffer
#(console-limit 1024)
##
# To bridge network traffic, like this:
#
# dom0: ----------------- bridge -> real eth0 -> the network
# |
# domU: fake eth0 -> vifN.0 -+
#
# use
#
# (network-script network-bridge)
#
# Your default ethernet device is used as the outgoing interface, by default.
# To use a different one (e.g. eth1) use
#
# (network-script 'network-bridge netdev=eth1')
#
# The bridge takes on the ethernet device name by default. To rename the
# bridge, use
#
# (network-script 'network-bridge bridge=<name>')
#
# It is possible to use the network-bridge script in more complicated
# scenarios, such as having two outgoing interfaces, with two bridges, and
# two fake interfaces per guest domain. To do things like this, write
# yourself a wrapper script, and call network-bridge from it, as appropriate.
#
# SuSE users note:
# On openSUSE >= 11.1 and SLES >= 11, networks should be configured using
# native platform tool - YaST. vif-bridge and qemu-ifup can be used to
# connect vifs to the YaST-managed networks.
#(network-script network-bridge)
(network-script )
# The script used to control virtual interfaces. This can be overridden on a
# per-vif basis when creating a domain or a configuring a new vif. The
# vif-bridge script is designed for use with the network-bridge script, or
# similar configurations.
#
# If you have overridden the bridge name using
# (network-script 'network-bridge bridge=<name>') then you may wish to do the
# same here. The bridge name can also be set when creating a domain or
# configuring a new vif, but a value specified here would act as a default.
#
# If you are using only one bridge, the vif-bridge script will discover that,
# so there is no need to specify it explicitly.
#
(vif-script vif-bridge)
## Use the following if network traffic is routed, as an alternative to the
# settings for bridged networking given above.
#(network-script network-route)
#(vif-script vif-route)
## Use the following if network traffic is routed with NAT, as an alternative
# to the settings for bridged networking given above.
#(network-script network-nat)
#(vif-script vif-nat)
# dom0-min-mem is the lowest permissible memory level (in MB) for dom0.
# This is a minimum both for auto-ballooning (as enabled by
# enable-dom0-ballooning below) and for xm mem-set when applied to dom0.
(dom0-min-mem 512)
# Whether to enable auto-ballooning of dom0 to allow domUs to be created.
# If enable-dom0-ballooning = no, dom0 will never balloon out.
(enable-dom0-ballooning no)
# In SMP system, dom0 will use dom0-cpus # of CPUS
# If dom0-cpus = 0, dom0 will take all cpus available
(dom0-cpus 0)
# Whether to enable core-dumps when domains crash.
#(enable-dump no)
# The tool used for initiating virtual TPM migration
#(external-migration-tool '')
# The interface for VNC servers to listen on. Defaults
# to 127.0.0.1 To restore old 'listen everywhere' behaviour
# set this to 0.0.0.0
#(vnc-listen '127.0.0.1')
# The default password for VNC console on HVM domain.
# Empty string is no authentication.
(vncpasswd '')
# The VNC server can be told to negotiate a TLS session
# to encryption all traffic, and provide x509 cert to
# clients enalbing them to verify server identity. The
# GTK-VNC widget, virt-viewer, virt-manager and VeNCrypt
# all support the VNC extension for TLS used in QEMU. The
# TightVNC/RealVNC/UltraVNC clients do not.
#
# To enable this create x509 certificates / keys in the
# directory /etc/xen/vnc
#
# ca-cert.pem - The CA certificate
# server-cert.pem - The Server certificate signed by the CA
# server-key.pem - The server private key
#
# and then uncomment this next line
# (vnc-tls 1)
# The certificate dir can be pointed elsewhere..
#
# (vnc-x509-cert-dir /etc/xen/vnc)
# The server can be told to request & validate an x509
# certificate from the client. Only clients with a cert
# signed by the trusted CA will be able to connect. This
# is more secure the password auth alone. Passwd auth can
# used at the same time if desired. To enable client cert
# checking uncomment this:
#
# (vnc-x509-verify 1)
# The default keymap to use for the VM's virtual keyboard
# when not specififed in VM's configuration
#(keymap 'en-us')
# Script to run when the label of a resource has changed.
#(resource-label-change-script '')
# Rotation count of qemu-dm log file.
#(qemu-dm-logrotate-count 10)
# Path where persistent domain configuration is stored.
# Default is /var/lib/xend/domains/
#
#(xend-domains-path /var/lib/xend/domains)
# Domain Locking
# In a multihost environment, domain locking prevents simultaneously
# running a domain on more than one host.
#
# If enabled, xend will execute a external lock utility (defined below)
# on each domain start and stop event. Disabled by default. Set to yes
# to enable domain locking.
#
#(xend-domain-lock no)
# Path where domain lock is stored if xend-domain-lock is enabled.
# Note: This path must be accessible to all VM Servers participating
# in domain locking, e.g. by specifying a shared mount point.
# Lock is placed in /<xend-domain-lock-path>/<domain-uuid>.
# Default is /var/lib/xend/domains/
#
#(xend-domain-lock-path /var/lib/xend/domains)
# External locking utility called by xend for acquiring/releasing
# domain lock. By default /etc/xen/scripts/domain-lock will be used
# if xend-domain-lock is set to yes. Set to path of custom locking
# utility to override the default.
#
# Synopsis of lock-util:
# lock-util [-l|-u] -n <vm name> -i <vm uuid> -p <physical host> path"
# -l Acquire (create) lock
# -u Remove lock
# -n vm-name Name of domain
# -i vm-id Id or UUID of domain
# -p phy-host Name of physical host (dom0)
# path /<xend-domain-lock-path>/<vm-uuid>
# Return 0 on success, non-zero on error.
#
# lock-util [-s] path"
# -s Lock status. If lock is acquired, print any contents
# on stdout and return 0. Return non-zero if lock is
# available.
# path /<xend-domain-lock-path>/<vm-uuid>
# If lock is acquired, print any contents on stdout and return 0.
# Return non-zero if lock is available.
#
# Default lock-util behavior:
# On domain start event, domain-lock will create and flock(1)
# /<xend-domain-lock-path>/<vm-uuid>/lock. Every two seconds it
# will write <vm-name>, <vm-id>, <vm-host>, and <tick> to the lock.
# <tick> is running counter.
# On domain stop event, domain-lock will unlock and remove
# /<xend-domain-lock-path>/<vm-uuid>/lock.
#
# Note: If xend-domain-lock-path is a cluster-unaware file system,
# administrator intervention may be required to remove stale
# locks. Consider two hosts using NFS for xend-domain-lock-path
# when HostA, running vm1, crashes. HostB could not acquire a
# lock for vm1 since the NFS server holds an exclusive lock
# acquired by HostA. The lock file must be manually removed
# before starting vm1 on HostA.
#
#(xend-domain-lock-utility domain-lock)
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home