Hi Peter,
what is your config in detail?
MB,
Asus P5B Deluxe
CPU,
cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 15
model name : Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz
stepping : 6
cpu MHz : 2400.048
cache size : 4096 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx
lm constant_tsc pni monitor ds_cpl vmx est tm2 cx16 xtpr lahf_lm
bogomips : 4803.27
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 15
model name : Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz
stepping : 6
cpu MHz : 2400.048
cache size : 4096 KB
physical id : 0
siblings : 2
core id : 1
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx
lm constant_tsc pni monitor ds_cpl vmx est tm2 cx16 xtpr lahf_lm
bogomips : 4800.10
RAM,
cat /proc/meminfo
MemTotal: 2060180 kB
MemFree: 1995840 kB
Buffers: 5108 kB
Cached: 38040 kB
SwapCached: 0 kB
Active: 29632 kB
Inactive: 17112 kB
HighTotal: 1179200 kB
HighFree: 1134868 kB
LowTotal: 880980 kB
LowFree: 860972 kB
SwapTotal: 979832 kB
SwapFree: 979832 kB
Dirty: 4 kB
Writeback: 0 kB
AnonPages: 3564 kB
Mapped: 3204 kB
Slab: 10672 kB
PageTables: 224 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
CommitLimit: 2009920 kB
Committed_AS: 10620 kB
VmallocTotal: 114680 kB
VmallocUsed: 2660 kB
VmallocChunk: 111732 kB
VGA,
lspci -v
00:00.0 Host bridge: Intel Corporation P965/G965 Memory Controller Hub (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 81ea
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information
00:01.0 PCI bridge: Intel Corporation P965/G965 PCI Express Root Port
(rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00008000-0000afff
Memory behind bridge: ff600000-ff6fffff
Prefetchable memory behind bridge: 00000000bfe00000-00000000dfdfffff
Capabilities: [88] Subsystem: Intel Corporation Unknown device 0000
Capabilities: [80] Power Management version 3
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB
UHCI #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: bus master, medium devsel, latency 0, IRQ 169
I/O ports at e000 [size=32]
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB
UHCI #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: bus master, medium devsel, latency 0, IRQ 50
I/O ports at e080 [size=32]
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2
EHCI #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: bus master, medium devsel, latency 0, IRQ 58
Memory at ffaff400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 1 (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Prefetchable memory behind bridge: 00000000dfe00000-00000000dfefffff
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Capabilities: [a0] Power Management version 2
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 5 (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: ff700000-ff7fffff
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Capabilities: [a0] Power Management version 2
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB
UHCI #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: bus master, medium devsel, latency 0, IRQ 217
I/O ports at d800 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB
UHCI #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: bus master, medium devsel, latency 0, IRQ 225
I/O ports at d880 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB
UHCI #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: bus master, medium devsel, latency 0, IRQ 58
I/O ports at dc00 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2
EHCI #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: bus master, medium devsel, latency 0, IRQ 217
Memory at ffaff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2)
(prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ff800000-ff9fffff
Prefetchable memory behind bridge: 0000000088000000-00000000880fffff
Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC
Interface Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: bus master, medium devsel, latency 0
Capabilities: [e0] Vendor Specific Information
00:1f.2 SATA controller: Intel Corporation 82801HB (ICH8) SATA AHCI
Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 233
I/O ports at ec00 [size=8]
I/O ports at e880 [size=4]
I/O ports at e800 [size=8]
I/O ports at e480 [size=4]
I/O ports at e400 [size=32]
Memory at ffaff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/4 Enable+
Capabilities: [70] Power Management version 3
Capabilities: [a8] #12 [0010]
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Flags: medium devsel, IRQ 58
Memory at 88100000 (32-bit, non-prefetchable) [size=256]
I/O ports at 0400 [size=32]
01:00.0 VGA compatible controller: ATI Technologies Inc Unknown device
715f (prog-if 00 [VGA])
Subsystem: PC Partner Limited Unknown device e170
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at c0000000 (64-bit, prefetchable) [size=256M]
Memory at ff6f0000 (64-bit, non-prefetchable) [size=64K]
I/O ports at a000 [size=256]
Expansion ROM at ff6c0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Express Endpoint IRQ 0
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
01:00.1 Display controller: ATI Technologies Inc Unknown device 717f
Subsystem: PC Partner Limited Unknown device e171
Flags: bus master, fast devsel, latency 0
Memory at ff6e0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Express Endpoint IRQ 0
02:00.0 SATA controller: JMicron Technologies, Inc. JMicron
20360/20363 AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 81e4
Flags: bus master, fast devsel, latency 0, IRQ 169
Memory at ff7fe000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at ff7e0000 [disabled] [size=64K]
Capabilities: [68] Power Management version 2
Capabilities: [50] Express Legacy Endpoint IRQ 1
02:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363
AHCI Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 81e4
Flags: bus master, fast devsel, latency 0, IRQ 50
I/O ports at bc00 [size=8]
I/O ports at b880 [size=4]
I/O ports at b800 [size=8]
I/O ports at b480 [size=4]
I/O ports at b400 [size=16]
Capabilities: [68] Power Management version 2
04:01.0 Ethernet controller: Intel Corporation 82541PI Gigabit
Ethernet Controller (rev 05)
Subsystem: Intel Corporation PRO/1000 GT Desktop Adapter
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 209
Memory at ff9e0000 (32-bit, non-prefetchable) [size=128K]
Memory at ff9c0000 (32-bit, non-prefetchable) [size=128K]
I/O ports at cc00 [size=64]
Expansion ROM at 88000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device
04:02.0 Ethernet controller: Intel Corporation 82541PI Gigabit
Ethernet Controller (rev 05)
Subsystem: Intel Corporation PRO/1000 GT Desktop Adapter
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 217
Memory at ff980000 (32-bit, non-prefetchable) [size=128K]
Memory at ff960000 (32-bit, non-prefetchable) [size=128K]
I/O ports at c880 [size=64]
Expansion ROM at 88020000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device
RAM setting in bios?
I'm not sure what you're looking for
DRAM Frequency [Auto] (possible options are: Auto, DDR2-533MHz,
DDR2-667MHz, DDR2-800MHz, DDR2-889MHz, DDR2-1067MHz)
and in the North Brisge Chipset Config
Memory Remap Feature [Enabled]
Configure DRAM Timing by SPD [Enabled]
Static Read Control [Auto] (possible options are: Disable, Auto, Fast, Faster)
If you are looking for something else, don't hesitate in asking me.
Thanks.
Chris.
Peter
2007/6/22, Petersson, Mats <Mats.Petersson@xxxxxxx>:
>
>
> > -----Original Message-----
> > From: Chris Fanning [mailto:christopher.fanning@xxxxxxxxx]
> > Sent: 22 June 2007 12:42
> > To: Petersson, Mats
> > Cc: Peter Braun; Xen users mailing list
> > Subject: Re: [Xen-users] asus P5B Delux not booting xen (ACPI
> > problem?)
> >
> > Hi,
> >
> > > > After Steve mentioned the 2.6.19 kernel, I had a look around and
> > > > discovered that ubuntu packs 2.6.19-4 in the xen package.
> > > > So I did an ubuntu installation and installed their xen package.
> > > >
> > > > Same sort of results.
> > > > Sometimes it boot, sometimes it doesn''t. And the boot
> > process doesn't
> > > > always freeze at the same place either.
> > > >
> > > > I'm begining to think I've got faulty hardware.
> > >
> > > Yes, that's what I've been thinking. Or you've got a buggy
> > BIOS (just
> > > because there isn't a newer one doesn't mean that it's bug free!)
> > >
> > > Also, the fact that it's inconistent is an indication
> > towards it being a
> > > hardware problem rather than software - most of the time,
> > software that
> > > is reasonably well tested (e.g. 2.6.18 on Xen) is stable
> > when it comes
> > > to a general setup, so if it's unstable on a particular
> > platform, then
> > > it's probably because that particular platform. This is a
> > generalization
> > > of course, not always true.
> >
> > But, how does that explain that this machine seems to boot the vanilla
> > kernels ok?
>
> Hmm. I hadn't realized that this was the case - it makes it a bit more
> suspicious that Xen is at fault, but it could simply be that the
> timing/memory usage is different and causing the problem. I've seen more
> than one case of complaints to AMD tech support saying that "My
> processor works fine with OS A, but fails when I use OS B" (A and B
> usually Windows and Linux in some combination, but also different
> varieties of Windows or Linux builds). In some of these cases, it turns
> out that the processor is actually faulty on a particular usage pattern.
> More frequently, it's the fact that some OS's use more power than others
> and thus generating more heat and needing a better heatsink/fan, or a
> better power supply.
>
> I've seen HVM guests fail memtest86 when the entire machine running
> memtest86 doesn't show any problems.
>
> --
> Mats
> >
> > Chris.
> >
> > >
> > > --
> > > Mats
> > >
> > > --
> > > Mats
> > > >
> > > > Any thoughts?
> > > >
> > > > Chris.
> > > >
> > > >
> > > > On 6/22/07, Chris Fanning <christopher.fanning@xxxxxxxxx> wrote:
> > > > > Well, the news isn't so good.
> > > > > This morning I booted the machine and it froze with
> > > > > ACPI Exeption (acpi_processor_o681) :AE_NOT_FOUND,
> > > > Processor Device is
> > > > > not present [20060707]
> > > > > ACPI Getting cpuindex for acpi 0x3
> > > > >
> > > > > grr.
> > > > >
> > > > > I hit the reset button and it gets a little further and
> > fails at:
> > > > > ata1: SATA link up 3,0 Gpb (SStatus 123 Scontrol 200)
> > > > > ata1: qc timeout (cmd 0xec)
> > > > > ata1: failed to identify (I/0 error, err_mask = 0x0104)
> > > > > ata1: port is slow to resond, please be patient
> > > > > ata1: failes to respond (30 secs)
> > > > > ata1: COMRESET failed, device not ready
> > > > > ata1: hardreset failded
> > > > >
> > > > > Exactly the same as it did with the xen3.1 I compiled by hand.
> > > > >
> > > > > So, the 2.6.18-4 kernel that comes with the debian xen
> > > > package hasn't
> > > > > solved the issue.
> > > > >
> > > > > > > It's a common problem with Xen that it doesn't support
> > > > new hardware (e.g.,
> > > > > > > 965 boards) very well. This is because Xen is based on
> > > > older vanilla kernel
> > > > > > > versions and 965 support requires a >2.6.19 vanilla
> > > > kernel or else
> > > > > > > distro-specific drivers.
> > > > >
> > > > > Perhaps I should put this machine back in its box and
> > wait for the
> > > > > next xen version? :)
> > > > >
> > > > > Chris.
> > > > >
> > > > > On 6/21/07, Peter Braun <xenware@xxxxxxxxx> wrote:
> > > > > > I got working Xen 3.1 @ Debian Etch following the
> > > > howtoforge tutorial
> > > > > > on P5B Deluxe and was not facing such problem. Latest
> > > > Bios - 6GB RAM -
> > > > > > memory remaping enabled.
> > > > > >
> > > > > > Do you use 32bit or 64bit?
> > > > > >
> > > > > > In 32bit PAE w/o any problem - running both PV and FV guests.
> > > > > > Everything works fine.
> > > > > > In 64bit am still facing some slowdown - this problem is heavy
> > > > > > discussed on internet. Looks like its problem by design
> > > > of the i965.
> > > > > > This slowdown only occures when more than 2GB is
> > > > installed and trying
> > > > > > to run under 64bit.
> > > > > >
> > > > > > XenExpress is running w/o problem - easy install and HVM
> > > > W2k3 server
> > > > > > guests are blazing fast because of PV drivers included.
> > > > > >
> > > > > > According to the info of Steve Brueckner:
> > > > > >
> > > > > > I have to disagree with you statement about Xen and i965
> > > > based motherboards.
> > > > > >
> > > > > > Am running rock stable Gentoo 32bit Xen 3.04 with 2.6.16
> > > > server based
> > > > > > on Intel 965 motherboard. No stability nor speed isuess.
> > > > Custom made
> > > > > > dom0 kernel. SW raid, LVM, SATA is running in AHCI. Only
> > > > problem was
> > > > > > installation when I had to use CD-ROM connected via
> > USB - minor
> > > > > > problem for me. From the install there is no need for CD-ROM
> > > > > >
> > > > > > I am planning next with Xen 3.1 and question is which
> > > > chipset. Intel
> > > > > > 965 is facing problems with 4GB and more RAM under 64bit
> > > > OS in booth
> > > > > > Linux and Windows. I dont have tested i3000 based server
> > > > motherboard
> > > > > > yet and in question comes also brand new P35 chipset.
> > Does anybody
> > > > > > have some experience with them?
> > > > > >
> > > > > >
> > > > > > Peter
> > > > > >
> > > > > >
> > > > > >
> > > > > > 2007/6/21, Steve Brueckner <steve@xxxxxxxxxxxxxx>:
> > > > > > > It's a common problem with Xen that it doesn't support
> > > > new hardware (e.g.,
> > > > > > > 965 boards) very well. This is because Xen is based on
> > > > older vanilla kernel
> > > > > > > versions and 965 support requires a >2.6.19 vanilla
> > > > kernel or else
> > > > > > > distro-specific drivers. Furthermore, there is no easy
> > > > way to upgrade the
> > > > > > > Xen kernels. I had the same problem as you, although I
> > > > use Fedora instead
> > > > > > > of Debian. It's great that you're able to solve your
> > > > problem using an older
> > > > > > > version of Xen incorporated in Debian's packages.
> > > > > > >
> > > > > > > I'm just commenting in this thread to make some noise
> > > > about the problem.
> > > > > > > I'm hoping Xen will release a 3.1 version with a newer
> > > > kernel, or else make
> > > > > > > it easier for users to upgrade their own kernels.
> > > > > > >
> > > > > > > Steve Brueckner, ATC-NY
> > > > > > >
> > > > > > > -----Original Message-----
> > > > > > > From: Chris Fanning [mailto:christopher.fanning@xxxxxxxxx]
> > > > > > > Sent: Thursday, June 21, 2007 6:24 AM
> > > > > > > To: xen-users@xxxxxxxxxxxxxxxxxxx
> > > > > > > Subject: [Xen-users] asus P5B Delux not booting xen
> > > > (ACPI problem?)
> > > > > > >
> > > > > > > Hi,
> > > > > > >
> > > > > > > I'm going crazy trying to get Xen running on an ASUS
> > > > P5B Delux (latest BIOS
> > > > > > > installed).
> > > > > > >
> > > > > > > I've tried xen-3.0.4 and xen-3.1.0 (both compiled
> > from source)
> > > > > > >
> > > > > > > The boot process stalls with
> > > > > > > ACP: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (low
> > > > level) -> IRQ 18
> > > > > > > ahci: 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports ?
> > > > Gbps 0x3f impl SATA
> > > > > > > mode
> > > > > > > ahci: 0000:00:1f.2: flags: 64bit ilck stag led pmp pio
> > > > > > > ata1: SATA max UDMA/133 cmd 0xE102E900 ctl 0x0
> > bmdma 0x0 irq 18
> > > > > > > ata2: SATA max UDMA/133 cmd 0xE102E980 ctl 0x0
> > bmdma 0x0 irq 18
> > > > > > > ata1: port is slow to resond, please be patient
> > > > > > > ata1: failes to respond (30 secs)
> > > > > > > scsi0 :ahci
> > > > > > > ata2: port is slow to resond, please be patient
> > > > > > > ata2: failes to respond (30 secs)
> > > > > > >
> > > > > > > booting xen-3.1.0 adds some more info to the failure:
> > > > > > > ata1: SATA link up 3,0 Gpb (SStatus 123 Scontrol 200)
> > > > > > > ata1: qc timeout (cmd 0xec)
> > > > > > > ata1: failed to identify (I/0 error, err_mask = 0x0104)
> > > > > > > ata1: port is slow to resond, please be patient
> > > > > > > ata1: failes to respond (30 secs)
> > > > > > > ata1: COMRESET failed, device not ready
> > > > > > > ata1: hardreset failded
> > > > > > >
> > > > > > > But this doesn't always happen. 50% of the time, the
> > > > process stalls for
> > > > > > > about 6 secs on
> > > > > > > ACP: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (low
> > > > level) -> IRQ 18 And then
> > > > > > > continues correctly.
> > > > > > >
> > > > > > > I've tried passing acpi=off to the kernel but this
> > > > results in ExtINT not
> > > > > > > setpup in hardware but reported by MP table.
> > > > > > >
> > > > > > > When I boot this machine with vanilla debian etch,
> > > > there are no problems.
> > > > > > >
> > > > > > > Any ideas?
> > > > > > > Thanks.
> > > > > > > Chris.
> > > > > > >
> > > > > > > _______________________________________________
> > > > > > > Xen-users mailing list
> > > > > > > Xen-users@xxxxxxxxxxxxxxxxxxx
> > > > > > > http://lists.xensource.com/xen-users
> > > > > > >
> > > > > > > _______________________________________________
> > > > > > > Xen-users mailing list
> > > > > > > Xen-users@xxxxxxxxxxxxxxxxxxx
> > > > > > > http://lists.xensource.com/xen-users
> > > > > > >
> > > > > >
> > > > > > _______________________________________________
> > > > > > Xen-users mailing list
> > > > > > Xen-users@xxxxxxxxxxxxxxxxxxx
> > > > > > http://lists.xensource.com/xen-users
> > > > > >
> > > > >
> > > >
> > > > _______________________________________________
> > > > Xen-users mailing list
> > > > Xen-users@xxxxxxxxxxxxxxxxxxx
> > > > http://lists.xensource.com/xen-users
> > > >
> > > >
> > > >
> > >
> > >
> > >
> >
> >
> >
>
>
>
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home