Hi!
I can't boot NetBSD 3.1 DomU in my Debian Dom0. It fails to find boot/root
device.
The configuration file is:
$ cat /etc/xen/netbsd.kds.priv.cfg
kernel="/xen/dist/kernels/netbsd/netbsd-XEN3_DOMU"
extra="bootdev=/dev/wd0"
root = "/dev/wd0a"
memory='64'
name="netbsd.kds.priv"
dist = ['file:/xen/domains/netbsd.kds.priv/disk.img,0x3,w']
ip='10.0.2.17'
netmask='255.255.255.0'
gateway='10.0.2.2'
The DomU kernel was downloaded from
ftp://ftp.netbsd.org/pub/NetBSD/NetBSD-3.1/i386/binary/kernel/netbsd-XEN3_DOMU.gz
The boot sequence is the following:
akhavr@dom0 dist/kernels/netbsd $ sudo xm create -c netbsd.kds.priv.cfg
Using config file "/etc/xen/netbsd.kds.priv.cfg".
Started domain netbsd.kds.priv
Loaded initial symtab at 0xc047f948, strtab at 0xc04ac50c, # entries 11383
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 3.1 (XEN3_DOMU) #0: Tue Oct 31 04:58:28 UTC 2006
builds@xxxxxxxxxxxxx:/home/builds/ab/netbsd-3-1-RELEASE/i386/200610302053Z-obj/home/builds/ab/netbsd-3-1-RELEASE/src/sys/arch/i386/compile/XEN3_DOMU
total memory = 61464 KB
avail memory = 59972 KB
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: AMD Athlon Model 2 (686-class), 2010.38 MHz, id 0x623
cpu0: features 2799fbfd<FPU,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 2799fbfd<PGE,MCA,CMOV,PAT,MPC,NOX,MMX>
cpu0: features 2799fbfd<FXSR,SSE,SSE2,LONG>
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 512 KB 64B/line 16-way
cpu0: ITLB 255 4 KB entries direct-mapped, 255 4 MB entries direct-mapped
cpu0: DTLB 255 4 KB entries direct-mapped, 255 4 MB entries direct-mapped
cpu0: 8 page colors
hypervisor0 at mainbus0
debug virtual interrupt using event channel 3
xenbus0 at hypervisor0: Xen Virtual Bus Interface
xenbus0: using event channel 1
xencons0 at hypervisor0: Xen Virtual Console Driver
xencons0: console major 143, unit 0
xencons0: using event channel 2
npx0 at hypervisor0: using exception 16
Xen clock: using event channel 4
raidattach: Asked for 8 units
Kernelized RAIDframe activated
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
Searching for RAID components...
boot device: <unknown>
root device:
use one of: raid0[a-p] raid1[a-p] raid2[a-p] raid3[a-p] raid4[a-p] raid5[a-p]
raid6[a-p] raid7[a-p] ddb halt reboot
root device: %
It doesn't depend on any extra="bootdev..." or root = "/dev/wd0a" values as
well on files line. Actually it produced the same output when the root
image wasn't there.
Googling didn't produce anything helpful.
Any ideas?
Thanks in advance!
--
Andrey V Khavryuchenko
Software Development Company http://www.kds.com.ua/
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home