On 24 Oct 2006 at 16:35, Roger Lucas wrote:
> Hi Ulrich,
>
> Use use "recursive LVM" as you describe it here with 3.0.2 and it works fine.
> You need to be careful with your Dom0 LVM
> configuration, however, and this may be related to your problem (but I an not
> sure).
>
> If you are using a typical LVM config, then the Dom0 LVM will scan all the
> block devices in Dom0 looking for LVM data at startup as
> part of the "vgchange -ay" command which is typically in a startup script
> somewhere. If you have an LVM in a DomU on top of an
> exported LVM block device from Dom0, you may have the situation where the
> Dom0 finds the LVM belonging to the DomU during the Dom0
> LVM scan. This is _bad_.
Hi Roger!
Actually it did not happen so far, because I haven't rebooted Dom0 since
creation
of the sub-VGs
>
> The simple solution is to use the "filter" option in /etc/lvm/lvm.conf to
> explicitly include only the drives on which you know you
> have the Dom0 LVMs present. We use:
>
> /etc/lvm/lvm.conf:
> <snip>
> filter =[ "a|/dev/hd*|", "a|/dev/sd*|", "a|/dev/md0|", "r|.*|" ]
> <snip>
Good tip!
>
> This allows /dev/hda, /dev/hdb, ..., /dev/sda, /dev/sdb,... and /dev/md0 but
> removes everything else. You will now not get both the
> Dom0 and the DomU trying to activate the same LVM volumes and all should run
> smoothly.
>
> We can then map the disk partitions in a DomU as:
>
> /etc/xen/harpseal:
> <snip>
> disk =
> ['phy:/dev/bigraid/harpseal,hda1,w','phy:/dev/bigraid/harpseal-lvm,hda2,w']
> <snip>
>
> "/dev/bigraid" is a large LVM VG on Dom0. "/dev/bigraid/harpseal" is a small
> LVM volume holding the DomU boot disk image.
> "/dev/bigraid/harpseal-lvm" is a larger LVM volume that the DomU considers as
> an LVM PV.
>
> Like I said, I don't know if this is the root cause of your problem, but you
> definitely need to get this config right anyhow or you
> are storing a whole world of pain for a later date...
Seems my problem is why the initrd fails to find the root LV. I'd like to
update
DomU first with patches, but for that I'll have to boot it first. Hmm..
Regards,
Ulrich
>
> Best regards,
>
> Roger
>
> > -----Original Message-----
> > From: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
> > [mailto:xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On
> > Behalf Of Ulrich Windl
> > Sent: 24 October 2006 16:21
> > To: xen-users@xxxxxxxxxxxxxxxxxxx
> > Subject: [Xen-users] Recursive LVM
> >
> > Hi!
> >
> > People are saying you shouldn't do it, but as it seems nice by cincept I
> > did it:
> >
> > Dom0 uses LVM to manage disk space, creating a large locical volume (LV)
> > for each
> > VM. I use the LV as a block device in DomU then, and DomU itself manages
> > disk
> > space using LVM, too.
> >
> > People warned me that the VG (volume group) names must be unique, so I did
> > that. I
> > installed the system just fine, but when rebooting DomU, no root filesystem
> > can be
> > found:
> >
> > ...
> > bootloader = '/usr/lib/xen/boot/domUloader.py'
> > bootentry = 'hda1:/vmlinuz-xen,/boot/initrd-xen'
> > ...
> >
> > Traceback (most recent call last):
> > File "/usr/lib/xen/boot/domUloader.py", line 505, in ?
> > main(sys.argv)
> > File "/usr/lib/xen/boot/domUloader.py", line 499, in main
> > sxpr = copyKernelAndInitrd(fs, kernel, initrd)
> > File "/usr/lib/xen/boot/domUloader.py", line 404, in copyKernelAndInitrd
> > raise RuntimeError("domUloader: Filesystem %s not exported\n" % fs)
> > RuntimeError: domUloader: Filesystem hda1 not exported
> >
> > Error: Boot loader didn't return any data!
> >
> > When mounting the LV to another bootable VM, "fdisk -l" reports three
> > partitions:
> > hda1 (/boot)
> > hda2 (swap)
> > hda3 (LVM, rest of the filesystems)
> >
> > However the partitions have names like hda1p1 hda1p2 hda1p3
> >
> > When I boot using another kernel, I get:
> >
> > kernel = '/boot/vmlinuz-2.6.16.21-0.25-xen'
> > ramdisk = '/boot/initrd-2.6.16.21-0.25-xen'
> > root = '/dev/as1/root'
> >
> > ...
> >
> > Loading xenblk
> > Registering block device major 3
> > hda:Loading dm-mod
> > unknown partition table
> > device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@xxxxxxxxxx
> > hdb:Loading dm-snapshot
> > ata_id[473]: main: HDIO_GET_IDENTITY failed for '/dev/.tmp-3-0'
> > Waiting for /dev/mapper/control to appear: ok
> > Loading reiserfs
> > Unable to find volume group "as1"
> > Waiting for device /dev/as1/root to appear: .. unknown partition table
> > ata_id[497]: main: HDIO_GET_IDENTITY failed for '/dev/.tmp-3-64'
> > ............................not found -- exiting to /bin/sh
> > [...]
> >
> > Besides those problems, I wonder how I can loop-mount the LV the way XEN ()
> > does
> > it:
> > PID TTY STAT TIME COMMAND
> > 20219 ? S< 0:00 [xvd 14 07:00]
> > 20220 ? S< 0:00 [xvd 14 fd:00]
> >
> > With 3.0.2 I made the bad experience that I can attach a block device to
> > the Dom0,
> > but I cannot detach it. Thus no DomU can use it until reboot. Kind of nasty
> > bug...
> >
> > Any cool hints? System is SLES10 on x86_64...
> >
> > Regards,
> > Ulrich
> >
> >
> > _______________________________________________
> > Xen-users mailing list
> > Xen-users@xxxxxxxxxxxxxxxxxxx
> > http://lists.xensource.com/xen-users
>
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home