[Xen-users] xen 3 networking concepts

Hi,

I just started using xen-unstable since I have a machine that will
not work with -stable.  I'm having problems with the new network
interfaces and I can't find anything in the xen 3 user guide to
explain what I'm seeing, so I don't know whether I am just missing
something or if there is actually a problem.

I'm on Debian, so here's my /etc/network/interfaces:

        auto eth0
        iface eth0 inet static
                address 192.168.0.20
                netmask 255.255.255.0
                network 192.168.0.0
                broadcast 192.168.0.255
                gateway 192.168.0.7

Here's what my ifconfig -a looks like immediately after boot but
before xend is started:

        eth0      Link encap:Ethernet  HWaddr 00:0B:6A:A7:DD:76
                  inet addr:192.168.0.20  Bcast:192.168.0.255  
Mask:255.255.255.0
                  inet6 addr: fe80::20b:6aff:fea7:dd76/64 Scope:Link
                  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
                  RX packets:92 errors:0 dropped:0 overruns:0 frame:0
                  TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
                  collisions:0 txqueuelen:1000
                  RX bytes:11200 (10.9 KiB)  TX bytes:1511 (1.4 KiB)
                  Interrupt:11 Base address:0xd400

        veth0     Link encap:Ethernet  HWaddr 00:00:00:00:00:00
                  BROADCAST MULTICAST  MTU:1500  Metric:1
                  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
                  TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
                  collisions:0 txqueuelen:0
                  RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

        (same up to veth7)

        vif0.0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
                  BROADCAST MULTICAST  MTU:1500  Metric:1
                  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
                  TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
                  collisions:0 txqueuelen:0
                  RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

        (same up to vif0.7)

Output of "ip ro":

        192.168.0.0/24 dev eth0  proto kernel  scope link  src 192.168.0.20
        default via 192.168.0.7 dev eth0

And of course networking works at this stage.

After starting xend, with the default bridging setup, the following
kernel messages are displayed:

        Bridge firewalling registered
        device vif0.0 entered promiscuous mode
        xen-br0: port 1(vif0.0) entered learning state
        device eth0 entered promiscuous mode
        xen-br0: port 2(eth0) entered learning state
        xen-br0: topology change detected, propogating
        xen-br0: port 1(vif0.0) entered forwarding state
        xen-br0: topology change detected, propogating
        xen-br0: port 2(eth0) entered forwarding state
        eth0: Media Link On 100mbps full-duplex

"ifconfig -a" output looks like:

        eth0      Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
                  inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
                  UP BROADCAST RUNNING NOARP MULTICAST  MTU:1500  Metric:1
                  RX packets:99 errors:0 dropped:0 overruns:0 frame:0
                  TX packets:36 errors:0 dropped:0 overruns:0 carrier:0
                  collisions:0 txqueuelen:1000
                  RX bytes:12369 (12.0 KiB)  TX bytes:2429 (2.3 KiB)
                  Interrupt:11 Base address:0xd400

        veth0     Link encap:Ethernet  HWaddr 00:0B:6A:A7:DD:76
                  inet addr:192.168.0.20  Bcast:192.168.0.255  
Mask:255.255.255.255
                  inet6 addr: fe80::20b:6aff:fea7:dd76/64 Scope:Link
                  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
                  RX packets:16 errors:0 dropped:0 overruns:0 frame:0
                  TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
                  collisions:0 txqueuelen:0
                  RX bytes:1835 (1.7 KiB)  TX bytes:714 (714.0 b)

        veth1     Link encap:Ethernet  HWaddr 00:00:00:00:00:00
                  BROADCAST MULTICAST  MTU:1500  Metric:1
                  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
                  TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
                  collisions:0 txqueuelen:0
                  RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

        (same up to veth7)

        vif0.1    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
                  BROADCAST MULTICAST  MTU:1500  Metric:1
                  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
                  TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
                  collisions:0 txqueuelen:0
                  RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

        (same up to vif0.7)

        xen-br0   Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
                  inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
                  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
                  RX packets:11 errors:0 dropped:0 overruns:0 frame:0
                  TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
                  collisions:0 txqueuelen:0
                  RX bytes:1285 (1.2 KiB)  TX bytes:378 (378.0 b)

"ip ro" is now as follows:

        192.168.0.0/24 dev veth0  proto kernel  scope link  src 192.168.0.20
        default via 192.168.0.7 dev veth0

and networking does not work.

I can make it work by doing following:

# ip addr add 192.168.0.20 dev xen-br0
# ip ro del 192.168.0.0/24
# ip ro del default
# ip ro add default via 192.168.0.7 dev xen-br0

Is this normal?  What is the neatest way to make it so my debian box
is going to have working network connectivity after a reboot and
xend starts?

Cheers,
Andy

signature.asc
Description: Digital signature

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

WARNING - OLD ARCHIVES

xen-users

[Xen-users] xen 3 networking concepts