Here is what I get when I do an ifconfig -a. eth0 is the physical
card/address. How do I configure the virtual interface with a
different IP and connect to it via ssh or telnet?
eth0 Link encap:Ethernet HWaddr 00:09:6B:8C:D5:54
inet addr:10.131.142.213 Bcast:10.131.142.255
Mask:255.255.255.128
inet6 addr: fe80::209:6bff:fe8c:d554/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:252681 errors:0 dropped:0 overruns:0 frame:0
TX packets:1284 errors:0 dropped:0 overruns:0 carrier:0
collisions:4 txqueuelen:1000
RX bytes:18191313 (17.3 MiB) TX bytes:183225 (178.9 KiB)
Interrupt:24
eth1 Link encap:Ethernet HWaddr 00:09:6B:8C:D5:55
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:25
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3096 errors:0 dropped:0 overruns:0 frame:0
TX packets:3096 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1824719 (1.7 MiB) TX bytes:1824719 (1.7 MiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:250606 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
xen-br0 Link encap:Ethernet HWaddr 00:09:6B:8C:D5:54
inet addr:10.131.142.213 Bcast:10.131.142.255
Mask:255.255.255.255
inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:252211 errors:0 dropped:0 overruns:0 frame:0
TX packets:1128 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13616114 (12.9 MiB) TX bytes:161560 (157.7 KiB)
------------------------------------------------------------------------
*From:* Michael J. Baysek [mailto:mjbaysek@xxxxxxxxxx]
*Sent:* Wednesday, September 14, 2005 4:08 PM
*To:* Johnson, Michael; xen-users@xxxxxxxxxxxxxxxxxxx
*Subject:* Basic Xen Questions
I did the favor of making a new thread for this...
Firstly. If you have not yet,
http://www.fedoraproject.org/wiki/FedoraXenQuickstart
I can tell you that even since FC4 was released, Xen has changed a
lot. Since the FC4 packages are reflecting the 3.0 development, using
the Xen 2.0 user guide is not 100% accurate, I have tried. Also, it
seems that the latest FC release 1447 of Xen is noticably different
than the 1398 release, as some of the xm commands are different.
Personally I would expect future releases to do the same so I suggest
test any upgrades on a staging server.
*About Network: *As long as you have nics=1 in your conf file for
your domU, the network device should be available in your guest OS as
eth0. In Redhat-esque style, you would edit your network config in
/etc/sysconfig/. I just copied /etc/sysconfig/network* from another
machine, and did a
grep -rin "192.168.0.3" /etc/sysconfig/*
for the IP of the machine I took the config from, and updated to the
new IP for my domU.
As far as *installing OS* other than FC4 inside of domU, I have
installed CentOS. Here are the steps I have used. I imagine you can
use this for any distro that uses Yum.
1. Create my image (I use LVM, but you can use loopback), mke2fs -j
to that image
2. Temporarily move /etc/yum.repos.d/* files out of that directory
3. Copy Centos-Base.repo into /etc/yum.repos.d/
4. Edit Centos-Base.repo to replace all the of variables with the
values you want. Yum can't install for a different releasever
and basearch, so you set these by hand in the repo file. You
could also install from local filesystem like DVD by using
file:// instead of http in the repo file.
5. Mount the image to /mnt/tmpdir
6. yum --installroot=/mnt/tmpdir -y groupinstall Base
7. Follow the rest of the steps in the Fedora Xen Howto for the rest.
I also have been running Gentoo 2005.0 which I moved over from
User-Mode-Linux.
Hope this helps.
Johnson, Michael wrote:
Hi,
Could you help me with a few Xen questions? It's basic stuff. I'm
looking at Xen for the first time. We have VMWare already up and
running and are happy with it but I was asked to look at Xen.
I installed FC4 from cd and chose to install everything, including Xen.
Following the Xen User's manual Xen v2.0 for x86 I have a dom0 setup and
created a second domain and called it rawhide.
Question,
How do I configure rawhide with an IP so I can either ssh or telnet to
it?
Have you installed other operating systems, i.e. RedHat EL3.0 to run in
a domain?
Thanks,
Mike
-----Original Message-----
From: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Michael J.
Baysek
Sent: Wednesday, September 14, 2005 2:21 PM
To: Eric Brown
Cc: xen-users@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-users] xm shutdown & xm destroy won't get rid of VM
I too have this problem:
# xm list
Name Id Mem(MB) CPU VCPU(s) State Time(s)
Domain-0 0 91 0 1 r---- 6753.9
lick 11 0 0 1 ----c 0.3
lick 11 0 0 1 ----c 0.3
lmon 4 255 0 1 -b--- 34997.5
lots 5 191 0 1 -b--- 5210.1
loud 6 511 0 1 ----- 6138.4
In my case this happened after I ran out of memory in the lick domU (no
swap was setup yet). The oom-killer hosed the domU. Even the console. So
I tried to destroy and start another. It was then that I did an xm list,
to my horror.
Eric Brown wrote:
I tried "xm shutdown" and then "xm destroy", my listing still shows:
$ xm list
Name Id Mem(MB) CPU State Time(s) Console Domain-0 0 156 0 r---- 766.2
asgtest0 9 0 3 -b--- 1.2 9609 debianarchive 15 255 1 -b--- 6.4 9615
What should i do to get rid of asgtest0?
Thanks!
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
--
Michael J. Baysek
Systems Analyst
Carnegie Mellon University, Auton Lab
http://www.autonlab.org
mjbaysek@xxxxxxxxxx
------------------------------------------------------------------------
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
Home