Re: [Xen-devel] Xen cannot boot with pvops dom0

[Patrick Colp <Patrick.Colp@xxxxxxxxxx>]

I don't think this is an issue with out the kernel was compiled. In fact, 
all of the ways mentioned will build the pvops kernel properly. I have run 
into a similar problem with the kernel trying to add/remove/modify ioapic 
stuff as well (and have tried to compile the kernel in every possible way, 
but still get the same problem).
I have a feeling it is an issue with the pvops kernel ioapic code and have 
spent some time trying to track it down, but haven't found anything yet.
The XCI 2.6.27 kernel works, though, so if you're just looking for a more 
modern kernel than 2.6.18, then I suggest using that. Hopefully this issue 
can be resolved soon, though. I would prefer to develop against the pvops 
kernel now that it's been selected as the xen-unstable default kernel.
Patrick


Jun Koi wrote:
> On Thu, Jun 25, 2009 at 6:20 PM, Han, Weidong<weidong.han@xxxxxxxxx> wrote:
> > I tried with latest Xen unstable (c/s 19833) with latest pvops dom0 (commit 
> > 384a55c0). Booting will hang, following is the serial console output:
> >
> > (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen
> > )
> > (XEN) Freed 128kB init memory.
> > mapping kernel into physical memory
> > Xen: setup ISA identity maps
> > about to get started...
> > (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
> > (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
> > (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
> > (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
> > (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
> > (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
> > (XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
> > (XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
> > (XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
> > (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
> > (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
> > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> > (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
> > (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
> > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> > (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
> > (XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
> > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> > (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
> > (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
> > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> > (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16 (and in fact, 
> > doing a make world/install will
> > (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
> > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> > (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
> > (XEN) ioapic_guest_write: old_entry=0000a921, new_entry=0001a921
> > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> >
> >
> > Did anyone meet this issue? Is there any difference on build and installation 
> > between pvops dom0 and 2.6.18 dom0? Following is my instructions, pls correct 
> > me if something is wrong. Appreciate in advance.
> >
> > My build and installation instructions:
> >        - cd xen-unstable.hg
> >        - make world (linux-2.6-pvops.git will be cloned)
> >        - make install
> >
> > My grub entry:
> >        title Xen - pvops
> >                root (hd0,2)
> >                kernel /boot/xen.gz dom0_mem=512m
> >                module /boot/vmlinuz-2.6-30.rc3-tip ro root=/dev/sda3 
> > console=tty0 console=ttyS0
> >
> > I also tried build pvops dom0 manually as follows, but it doesn't help.
> >        - cd linux-2.6-pvops.git
> >        - make
> >        - make modules_install
> >        - make install
> I am not quite sure if that is the correct way to recompile kernel, as
> sometimes I have some problems with Dom0 booting after that.
>
> I usually recompile Dom0 kernel this way: (from the root directory)
>
> # make linux-2.6-xen-config  (to configure kernel options)
> # make linux-2.6-xen-build
> # make linux-2.6-xen-install
>
> Then dont forget to "mkinitramfs", of course
>
> Thanks,
> J
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel