Re: [Xen-devel] Xen doesnt recognize my root fs, while native kernel can ???

["Jun Koi" <junkoi2004@xxxxxxxxx>]

Here is the screenshot taken with a digital camera. I hope the screen
is clear enough for you to see.

Thanks,
Jun



On 6/13/07, Jun Koi <junkoi2004@xxxxxxxxx> wrote:
> Hi Mats,
>
> On 6/13/07, Petersson, Mats <Mats.Petersson@xxxxxxx> wrote:
> >
> >
> > > -----Original Message-----
> > > From: xen-devel-bounces@xxxxxxxxxxxxxxxxxxx
> > > [mailto:xen-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Jun Koi
> > > Sent: 13 June 2007 09:54
> > > To: Keir Fraser
> > > Cc: xen-devel
> > > Subject: Re: [Xen-devel] Xen doesnt recognize my root fs,
> > > while native kernel can ???
> > >
> > > On 6/13/07, Keir Fraser <Keir.Fraser@xxxxxxxxxxxx> wrote:
> > > > On 13/6/07 08:49, "Jun Koi" <junkoi2004@xxxxxxxxx> wrote:
> > > >
> > > > >>> The point is that Xen doesnt boot in the first place,
> > > so I cannot
> > > > >>> provide xm dmesg!
> > > > >>>
> > > > >>> Below is the output from dmesg (native kernel) and
> > > Dom0's .config.
> > > > >>> Anything else do you need?
> > > > >>
> > > > >> Can you get a serial line on the machine?
> > > > >
> > > > > Opps, that is compicated, as I dont have a cable to do that.
> > > > >
> > > > > So if you have no suggestion, perhaps I must try this
> > > way. But perhaps
> > > > > it take more than a week, as I am away in few days.
> > > >
> > > > There's a decent chance that comparing the two dmesg
> > > outputs will show some
> > > > important deviation in the case of running on Xen that is
> > > causing the boot
> > > > failure. Without the failing output it's hard to know where to start
> > > > looking.
> > > >
> > >
> > > I see, but can you imagine some reasons why that happens?  It makes
> > > absolute no sense to me.
> >
> > There are lots of possible reasons. The most likely is that your kernel
> > in the native has drivers that are not part of the Xen default
> > configuration.
> >
> > The other very common problem is that you don't have those necessary
> > drivers in the "initrd" for your Xen. This is a problem that is posted
> > about three times a week (at least) on the Xen Users mailing list [where
> > this problem probably should be discussed - but I think since it's
> > started here, we'll keep it here].
> >
>
> No, that is not a reason in my case. I did it this way:
> - Native kernel (2.6.18) is compiled with all the necessary drivers
> built-in. That means I dont need initrd to boot my machine with this
> kernel. And it boots well.
> - I copied the .config of native kernel above to Dom0, and compile
> Dom0 with this option. (Of course before compiling, I enabled Xen
> option, as you can see in the .config of Dom0 I sent in the last
> mail). Again this time I dont need initrd.
>
> So it is logical that Dom0 must boot, but it fails actually. That is
> why I find the situation very strange.
>
>
> > > I have found that my machine has no serial port, so perhaps I must buy
> > > a serial card to debug this problem. Wonder if there is another way to
> > > avoid that (?)
> > If you have a digital camera and you add "noreboot" to the commandline
> > of "xen.gz" in your grub configuration, maybe you can upload (to some
> > photo-web-site or such) a screen-shot of the final few lines of the boot
> > and send a link to the list - that may not give all clues, but at least
> > it will indicate what's going on.
>
> OK, I will do that, as it is not desired to buy a serial card :-)
>
> Thanks,
> Jun

CIMG9950.JPG
Description: JPEG image

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel