Hi,
You should check I/O behavior.
If I/O occured,
other domain(vm1, vm2) data is handled by dom0 as driver domain.
Thanks
Atsushi SAKAI
"Harry Smith" <harry.smith272@xxxxxxxxx> wrote:
> Hi Atsushi & Pradeep,
>
> thanks for replying back.
> I have 4 VCPUs for each of VM. But the point I wanted to stress upon is -
> "This happened even in the case where CPU usage by both of vm1,vm2 is
> restricted to 100% each. "
> I had pinned all 4 VCPUs of each VM to a single phys. CPU. & I have 4 phys.
> CPUs
> means my vm1 was using cpu1, vm2 using cpu2 & domain-0 using cpu0,cpu3
>
> Problem is when there is no load on vm2, webserver performance of vm1 is
> better. But when vm2 has some compute-intense load then vm1 webserver
> performance goes down.
> Please note that CPU consumption of vm1 shown by xentop in both cases is
> 100%, still webserver performance goes down by around 15-20%.
> Even after trying to isolate two VMs, existence of load on one VM is
> affecting other.
>
> so is it expected behavior ?
>
> thanks,
> Harry
>
>
>
> On 5/10/07, pradeep singh rautela <rautelap@xxxxxxxxx> wrote:
> >
> >
> >
> > On 5/10/07, Atsushi SAKAI <sakaia@xxxxxxxxxxxxxx> wrote:
> > >
> > > One vcpu can use one pcpu at one time.
> > > It means 100% is maxium for one vcpu domain.
> > > If you want to use cpu resources, you should set more vcpu.
> >
> >
> > Ok, this explains a lot of things.
> > As i understand this , more VCPUs means more freedom to hypervisor to
> > migrate them among physical CPUs, depending on the free PCPUs available.
> >
> > In general
> >
> > domU1
> > / | \
> > vcpu1 vcpu2 vcpu3
> >
> > pcpu1 pcpu2 pcpu3 pcpu4 pcpu5 pcpu6
> >
> > I mean ,domU1 can run on any vcpu , right? now vcpu1, vcpu2, vcpu3 share a
> > one to many reationship between pcpus[1....6]. That is a vcpu can run on any
> > of the pcus available to the Xen hypervisor(unless i explicitly pin it to ).
> >
> >
> > Is my naive understanding of what you explained is correct?
> >
> > Thank you
> > ~psr
> >
> > > Thanks
> > > Atsushi SAKAI
> > >
> > >
> > > "pradeep singh rautela" <rautelap@xxxxxxxxx> wrote:
> > >
> > > > Hi Atsushi,
> > > >
> > > > On 5/10/07, Atsushi SAKAI < sakaia@xxxxxxxxxxxxxx> wrote:
> > > > >
> > > > >
> > > > > You should show detail configuration.
> > > > > Your information is too short.
> > > > >
> > > > > Anyway I guess each domain has one vcpu.
> > > > > If so, this is normal behavior.
> > > > > Because one vcpu cannot allocate two or more pcpu at once.
> > > >
> > > >
> > > > Right, but shouldn't Xen hypervisor be capable of migrating the VCPU
> > > among
> > > > the available PCPUs on a multiprocessor system, like in this case? And
> > > > criteria should be the load on the PCPU or the idle PCPUs.
> > > > yes/no?
> > > >
> > > > Am i missing something here?
> > > >
> > > > Thanks
> > > > ~psr
> > > >
> > > > Thanks
> > > > > Atsushi SAKAI
> > > > >
> > > > > "Harry Smith" <harry.smith272@xxxxxxxxx> wrote:
> > > > >
> > > > > > hi all,
> > > > > >
> > > > > > I am using xen3.0.3 on dual core hyperthreaded processor (in all 4
> > > > > cores).
> > > > > > There are 2 VMs vm1,vm2 among which vm1 has a webserver running on
> > > it.
> > > > > >
> > > > > > While testing the performance of webserver, when I introduce some
> > > load
> > > > > on
> > > > > > vm2 which involves some computations the webserver performance
> > > goes
> > > > > down.
> > > > > > This happened even in the case where CPU usage by both of vm1,vm2
> > > is
> > > > > > restricted to 100% each.
> > > > > >
> > > > > > Is it expected behavior ? if yes then how does one can control
> > > addition
> > > > > of
> > > > > > new virtual machines as adding every new VM will result in
> > > lowering
> > > > > > performance of other VMs. Through scheduling parameters we can
> > > just
> > > > > specify
> > > > > > amount of CPU to be used in relative sense (weight) & upper limit
> > > (cap).
> > > > > But
> > > > > > how to tackle this point.
> > > > > >
> > > > > > I am new in this area & wanna set up a lab using virtualization,
> > > so want
> > > > > to
> > > > > > find solution for this.
> > > > > >
> > > > > > thanks,
> > > > > > Harry
> > > > > >
> > > > > > we always have a choice...
> > > > >
> > > > >
> > > > >
> > > > > _______________________________________________
> > > > > Xen-devel mailing list
> > > > > Xen-devel@xxxxxxxxxxxxxxxxxxx
> > > > > http://lists.xensource.com/xen-devel
> > > > >
> > > >
> > > >
> > > >
> > > > --
> > > > ---
> > > > pradeep singh rautela
> > > >
> > > > "Genius is 1% inspiration, and 99% perspiration" - not me :)
> > >
> > >
> > >
> >
> >
> > --
> > ---
> > pradeep singh rautela
> >
> > "Genius is 1% inspiration, and 99% perspiration" - not me :)
> >
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home