Linux version 2.6.12.6-xen0 (root@xxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.0.2 20051125 (Red Hat 4.0.2-8)) #4 Sat Dec 24 21:39:37 CET 2005 BIOS-provided physical RAM map: Xen: 0000000000000000 - 0000000006000000 (usable) 0MB HIGHMEM available. 104MB LOWMEM available. On node 0 totalpages: 26624 DMA zone: 26624 pages, LIFO batch:15 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 PTLTD ) @ 0x000f6dd0 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x0eefb63b ACPI: FADT (v001 COMPAQ EAGLES 0x06040000 PTL_ 0x000f4240) @ 0x0eefeeb6 ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x0eefef2a ACPI: DSDT (v001 COMAPQ EAGLES 0x06040000 MSFT 0x0100000d) @ 0x00000000 IRQ lockup detection disabled Allocating PCI resources starting at 0f000000 (gap: 0f000000:f0f80000) Built 1 zonelists Kernel command line: root=/dev/hda6 ro console=tty1 lapic Initializing CPU#0 PID hash table entries: 512 (order: 9, 8192 bytes) Xen reported: 996.572 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Software IO TLB enabled: Aperture: 2 megabytes Bus range: 0x0000000007a00000 - 0x0000000007c00000 Kernel range: 0x00000000c061f000 - 0x00000000c081f000 vmalloc area: c7000000-fb7fe000, maxmem 34000000 Memory: 89728k/106496k available (3397k kernel code, 8416k reserved, 1064k data, 352k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 1985.74 BogoMIPS (lpj=9928704) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 64K (64 bytes/line) CPU: After all inits, caps: 0383d1f1 c1cbf9ff 00000000 00000020 00000000 00000000 00000000 CPU: AMD mobile AMD Duron(tm) Processor stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... disabled ACPI: setting ELCR to 0400 (from 0a30) NET: Registered protocol family 16 PCI: Using configuration type 1 ACPI: Subsystem revision 20050309 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Disabling VIA memory write queue (PCI ID 0305, rev 80): [55] 3c & 1f -> 1c Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs *4) ACPI: PCI Interrupt Link [LNKB] (IRQs *11) ACPI: PCI Interrupt Link [LNKC] (IRQs *5) ACPI: PCI Interrupt Link [LNKD] (IRQs *9) ACPI: Embedded Controller [EC] (gpe 6) xen_mem: Initialising balloon driver. SCSI subsystem initialized usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report Grant table initialized IA-32 Microcode Update Driver: v1.14-xen Initializing Cryptographic API Applying VIA southbridge workaround. PCI: Disabling Via external APIC routing serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) HP CISS Driver (v 2.6.6) Intel(R) PRO/1000 Network Driver - version 6.0.54-k2 Copyright (c) 1999-2004 Intel Corporation. pcnet32.c:v1.30j 29.04.2005 tsbogend@xxxxxxxxxxxxxxxx e100: Intel(R) PRO/100 Network Driver, 3.4.8-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation 8139too Fast Ethernet driver 0.9.27 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 eth0: RealTek RTL8139 at 0x1400, 00:08:02:2d:48:96, IRQ 11 eth0: Identified 8139 chip type 'RTL-8139C' tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky Xen virtual console successfully installed as ttyS0 Event-channel device installed. blkif_init: reqs=64, pages=704, mmap_vstart=0xc5c00000 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:07.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt82c686b (rev 42) IDE UDMA100 controller on pci0000:00:07.1 ide0: BM-DMA at 0x1840-0x1847, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1848-0x184f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: FUJITSU MHN2200AT, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: SR243T, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... hda: max request size: 128KiB hda: 39070080 sectors (20003 MB) w/2048KiB Cache, CHS=38760/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 > hda3 hda4 hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 Red Hat/Adaptec aacraid driver (1.1.2-lk2 Dec 24 2005) 3ware Storage Controller device driver for Linux v1.26.02.001. libata version 1.11 loaded. Fusion MPT base driver 3.01.20 Copyright (c) 1999-2004 LSI Logic Corporation Fusion MPT SCSI Host driver 3.01.20 usbmon: debugs is not available ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) USB Universal Host Controller Interface driver v2.2 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:07.2: irq 9, io base 0x00001800 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.01:USB HID core driver mice: PS/2 mouse device common for all mice md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 730.400 MB/sec raid5: using function: pIII_sse (730.400 MB/sec) md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx NET: Registered protocol family 2 input: AT Translated Set 2 keyboard on isa0060/serio0 atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. IP: routing cache hash table of 512 buckets, 4Kbytes TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 352k freed Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006 input: SynPS/2 Synaptics TouchPad on isa0060/serio1 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected VIA Twister-K/KT133x/KM133 chipset agpgart: AGP aperture is 64M @ 0xec000000 ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery absent) ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Lid Switch [LID] ibm_acpi: ec object not found ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Processor [CPU0] (supports 16 throttling states) ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) *************************************************************** *************************************************************** ** WARNING: Currently emulating unsupported memory accesses ** ** in /lib/tls glibc libraries. The emulation is ** ** slow. To ensure full performance you should ** ** install a 'xen-friendly' (nosegneg) version of ** ** the library, or disable tls support by executing ** ** the following as root: ** ** mv /lib/tls /lib/tls.disabled ** ** Offending process: nash (pid=1773) ** *************************************************************** *************************************************************** Pausing... 5Pausing... 4Pausing... 3Pausing... 2Pausing... 1Continuing... md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x50 { LastFailedSense=0x05 } ide: failed opcode was: unknown cdrom: open failed. EXT3 FS on hda6, internal journal Adding 265032k swap on /dev/hda5. Priority:-1 extents:1 ip_tables: (C) 2000-2002 Netfilter core team eth0: link down device vif0.0 entered promiscuous mode device peth0 entered promiscuous mode xenbr0: port 1(vif0.0) entering learning state xenbr0: topology change detected, propagating xenbr0: port 1(vif0.0) entering forwarding state peth0: link down peth0: Promiscuous mode enabled. peth0: Promiscuous mode enabled. peth0: Promiscuous mode enabled. usbcore: registered new driver cdc_acm drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters