Re: [Xen-devel] Re: [Xen-users] xen 3.0 boot problem

[Andrew Theurer <habanero@xxxxxxxxxx>]

Ian Pratt wrote:

>  
>
> > Well, i'm using here the qla2340 on several boxes. It works 
> > with Xen 2.0 but noch with Xen 3.0. as part of SUSE Linux 10.0:
> >    
> Interesting. If the driver really doews work flawlessly in Xen 2, then I think 
> the culprit has to be interrupt routeing.
>
> Under Xen 3, does /proc/interrupts show you're receiving interrupts?
>
> Do other devices with high irq numbers appear to be working OK?
>  
I have been using a qla2300 on xen with never an issue, but it's on irq 
52.  I do recall a long long time ago seeing something like this on much 
higer irqs on some other adapter, but I can't recall the details at the 
moment.  Is there any way to get that adapter to use a much lower irq?
-Andrew

> Ian
>
>  
>  
>
> > kernel-xen-2.6.13-15
> > kernel-xen-nongpl-2.6.13-15
> > xen-3.0_6715-2
> >
> > System startup with xen kernel fails on detecting the boot 
> > device, which is attached to the qla2300 fibre channel host 
> > bus adapter.
> > qla2300 0000:05:01.0: Found an ISP2312, irq 185, iobase 
> > 0xf8812000 qla2300 0000:05:01.0: Configuring PCI space...
> > qla2300 0000:05:01.0: Configure NVRAM parameters...
> > qla2300 0000:05:01.0: Verifying loaded RISC code...
> > qla2300 0000:05:01.0: Waiting for LIP to complete...
> >
> > Until here it's alle fine, but then:
> >
> > qla2300 0000:05:01.0: LIP reset occured (f7f7).
> > qla2300 0000:05:01.0: LOOP UP detected (2 Gbps).
> > qla2300 0000:05:01.0: Topology - (F_Port), Host Loop address 0xffff
> > scsi3 : qla2xxx
> > qla2300 0000:04:02.0:
> > QLogic Fibre Channel HBA Driver: 8.01.00b5-k
> >  QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
> >  ISP2312: PCI-X (100 MHz) @ 0000:05:01.0 hdma+, host#=3, 
> > fw=3.03.15 IPX Loading kernel/fs/reiserfs/reiserfs.ko Waiting 
> > for device /dev/sda4 to appear: .....not found --- exiting to 
> > /bin/sh $
> > With the 2.6.13-15-smp kernel as part of SUSE Linux 10 it 
> > goes on without any problem:
> > SCSI device sda: 41943040 512-byte hdwr sectors (21475 MB) 
> > SCSI device sda: drive cache: write back SCSI device sda: 
> > 41943040 512-byte hdwr sectors (21475 MB) SCSI device sda: 
> > drive cache: write back
> > sda: sda1 sda2 sda3 sda4
> > ....etc.
> >
> > Stephan
> >
> >
> >         -----Ursprüngliche Nachricht-----
> >         Von: The Smoking Man [mailto:datashark@xxxxxxxxx]
> >         Gesendet: Freitag, 7. Oktober 2005 19:13
> >         An: Ian Pratt
> > 	Cc: xen-devel@xxxxxxxxxxxxxxxxxxx; Stephan Böni; 
> > xen-users@xxxxxxxxxxxxxxxxxxx
> >         Betreff: [Xen-devel] Re: [Xen-users] xen 3.0 boot problem
> >         
> >         
> > 	Beein used here the qla2344 on several boxes. works  
> > trully fine  on  gentoo-xensources (vanilla kernel plus xen 
> > patches) and (this is what i'm using in production) with suse 
> > kotd sources. 
> > 	
> > 	Bellow is the relevant bootlog... 
> > 	
> >         Best regards,
> >         
> >         [    6.599201] QLogic Fibre Channel HBA Driver
> > 	[    6.599446] ACPI: PCI Interrupt 0000:02:04.0[A] -> 
> > GSI 29 (level, low) -> IRQ 29
> > 	[    6.599749] qla2300 0000:02:04.0: Found an ISP2312, 
> > irq 29, iobase 0xe8804000
> >         [    6.600392] qla2300 0000:02:04.0: Configuring PCI space...
> > 	[    6.600687] qla2300 0000:02:04.0: Configure NVRAM 
> > parameters...
> > 	[    6.685681] qla2300 0000:02:04.0: Verifying loaded 
> > RISC code...
> > 	[    6.809175] qla2300 0000:02:04.0: Waiting for LIP to 
> > complete...
> >         [   27.200114] qla2300 0000:02:04.0: Cable is unplugged...
> >         [   27.200289] scsi0 : qla2xxx
> >         [   27.200579] qla2300 0000:02:04.0:
> >         [   27.200580]  QLogic Fibre Channel HBA Driver: 8.00.02b5-k
> >         [   27.200581]   QLogic QLA2344 -
> > 	[   27.200582]   ISP2312: PCI-X (133 MHz) @ 
> > 0000:02:04.0 hdma+, host#=0, fw=3.03.08 IPX
> > 	[   27.201211] ACPI: PCI Interrupt 0000:02:04.1[B] -> 
> > GSI 30 (level, low) -> IRQ 30
> > 	[   27.201482] qla2300 0000:02:04.1: Found an ISP2312, 
> > irq 30, iobase 0xe8806000
> >         [   27.202082] qla2300 0000:02:04.1: Configuring PCI space...
> > 	[   27.202369] qla2300 0000:02:04.1: Configure NVRAM 
> > parameters...
> > 	[   27.287483] qla2300 0000:02:04.1: Verifying loaded 
> > RISC code...
> > 	[   27.410625] qla2300 0000:02:04.1: Waiting for LIP to 
> > complete...
> >         [   47.810115] qla2300 0000:02:04.1: Cable is unplugged...
> >         [   47.810279] scsi1 : qla2xxx
> >         [   47.810504] qla2300 0000:02:04.1:
> >         [   47.810505]  QLogic Fibre Channel HBA Driver: 8.00.02b5-k
> >         [   47.810507]   QLogic QLA2344 -
> > 	[   47.810508]   ISP2312: PCI-X (133 MHz) @ 
> > 0000:02:04.1 hdma+, host#=1, fw=3.03.08 IPX
> > 	[   47.811136] ACPI: PCI Interrupt 0000:02:06.0[A] -> 
> > GSI 31 (level, low) -> IRQ 31
> > 	[   47.811404] qla2300 0000:02:06.0: Found an ISP2312, 
> > irq 31, iobase 0xe881a000
> >         [   47.812006] qla2300 0000:02:06.0: Configuring PCI space...
> > 	[   47.812295] qla2300 0000:02:06.0: Configure NVRAM 
> > parameters...
> > 	[   47.897025] qla2300 0000:02:06.0: Verifying loaded 
> > RISC code...
> > 	[   48.020170] qla2300 0000:02:06.0: Waiting for LIP to 
> > complete...
> >         [   68.410104] qla2300 0000:02:06.0: Cable is unplugged...
> >         [   68.410270] scsi2 : qla2xxx
> >         [   68.410514] qla2300 0000:02:06.0:
> >         [   68.410515]  QLogic Fibre Channel HBA Driver: 8.00.02b5-k
> >         [   68.410517]   QLogic QLA2344 -
> > 	[   68.410518]   ISP2312: PCI-X (133 MHz) @ 
> > 0000:02:06.0 hdma+, host#=2, fw=3.03.08 IPX
> > 	[   68.411144] ACPI: PCI Interrupt 0000:02:06.1[B] -> 
> > GSI 28 (level, low) -> IRQ 28
> > 	[   68.411413] qla2300 0000:02:06.1: Found an ISP2312, 
> > irq 28, iobase 0xe881c000
> >         [   68.412024] qla2300 0000:02:06.1: Configuring PCI space...
> > 	[   68.412311] qla2300 0000:02:06.1: Configure NVRAM 
> > parameters...
> > 	[   68.497424] qla2300 0000:02:06.1: Verifying loaded 
> > RISC code...
> > 	[   68.516876] qla2300 0000:02:06.1: Waiting for LIP to 
> > complete...
> >         [   69.020063] qla2300 0000:02:06.1: LIP reset occured (f8f7).
> >         [   69.020220] qla2300 0000:02:06.1: LIP occured (f8f7).
> >         [   69.020370] qla2300 0000:02:06.1: LOOP UP detected (2 Gbps).
> > 	[   69.020661] qla2300 0000:02:06.1: Topology - (Loop), 
> > Host Loop address 0x0
> >         [   69.021595] scsi3 : qla2xxx
> >         [   69.021824] qla2300 0000:02:06.1:
> >         [   69.021825]  QLogic Fibre Channel HBA Driver: 8.00.02b5-k
> >         [   69.021826]   QLogic QLA2344 -
> > 	[   69.021827]   ISP2312: PCI-X (133 MHz) @ 
> > 0000:02:06.1 hdma+, host#=3, fw=3.03.08 IPX
> >         [   69.025082] mice: PS/2 mouse device common for all mice
> > 	[   69.025227] md: md driver 0.90.1 MAX_MD_DEVS=256, 
> > MD_SB_DISKS=27
> >         [   69.025434] NET: Registered protocol family 2
> > 	[   69.025850]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.026240]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.027076] SCSI device sda: 131072 512-byte hdwr 
> > sectors (67 MB)
> >         [   69.027919] SCSI device sda: drive cache: write through
> > 	[   69.028521] SCSI device sda: 131072 512-byte hdwr 
> > sectors (67 MB)
> >         [   69.029354] SCSI device sda: drive cache: write through
> >         [   69.029495]  sda: sda1
> > 	[   69.030035] Attached scsi disk sda at scsi3, channel 
> > 0, id 0, lun 0
> > 	[   69.031081]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.031466]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.032195] SCSI device sdb: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.032943] SCSI device sdb: drive cache: write through
> > 	[   69.033469] SCSI device sdb: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.034213] SCSI device sdb: drive cache: write through
> >         [   69.034353]  sdb: sdb1
> > 	[   69.048548] Attached scsi disk sdb at scsi3, channel 
> > 0, id 0, lun 1
> > 	[   69.049188]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.049573]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.050305] SCSI device sdc: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.051056] SCSI device sdc: drive cache: write through
> > 	[   69.051586] SCSI device sdc: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.052341] SCSI device sdc: drive cache: write through
> >         [   69.052481]  sdc: sdc1
> > 	[   69.065097] Attached scsi disk sdc at scsi3, channel 
> > 0, id 0, lun 2
> > 	[   69.065589]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.065973]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.066583] SCSI device sdd: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.067279] SCSI device sdd: drive cache: write through
> > 	[   69.067695] SCSI device sdd: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.068303] SCSI device sdd: drive cache: write through
> >         [   69.068442]  sdd: sdd1
> > 	[   69.078452] Attached scsi disk sdd at scsi3, channel 
> > 0, id 0, lun 3
> > 	[   69.078969]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.079355]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.080403] SCSI device sde: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.081042] SCSI device sde: drive cache: write through
> > 	[   69.081458] SCSI device sde: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.082098] SCSI device sde: drive cache: write through
> >         [   69.082237]  sde: sde1
> > 	[   69.093087] Attached scsi disk sde at scsi3, channel 
> > 0, id 0, lun 4
> > 	[   69.093592]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.093976]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.094591] SCSI device sdf: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.095206] SCSI device sdf: drive cache: write through
> > 	[   69.095615] SCSI device sdf: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.096234] SCSI device sdf: drive cache: write through
> >         [   69.096373]  sdf: sdf1
> > 	[   69.108174] Attached scsi disk sdf at scsi3, channel 
> > 0, id 0, lun 5
> > 	[   69.108790]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.109175]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.110034] SCSI device sdg: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.110638] SCSI device sdg: drive cache: write through
> > 	[   69.111046] SCSI device sdg: 12582912 512-byte hdwr 
> > sectors (6442 MB)
> >         [   69.111645] SCSI device sdg: drive cache: write through
> >         [   69.111784]  sdg: sdg1
> > 	[   69.122286] Attached scsi disk sdg at scsi3, channel 
> > 0, id 0, lun 6
> > 	[   69.122777]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.123163]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.123772] SCSI device sdh: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.124377] SCSI device sdh: drive cache: write through
> > 	[   69.124789] SCSI device sdh: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.125393] SCSI device sdh: drive cache: write through
> >         [   69.125532]  sdh: sdh1
> > 	[   69.134481] Attached scsi disk sdh at scsi3, channel 
> > 0, id 0, lun 7
> > 	[   69.134971]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.135355]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.135974] SCSI device sdi: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.136577] SCSI device sdi: drive cache: write through
> > 	[   69.136994] SCSI device sdi: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.137597] SCSI device sdi: drive cache: write through
> >         [   69.137736]  sdi: sdi1
> > 	[   69.142544] Attached scsi disk sdi at scsi3, channel 
> > 0, id 0, lun 8
> > 	[   69.143037]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.143421]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.144036] SCSI device sdj: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.144635] SCSI device sdj: drive cache: write through
> > 	[   69.145044] SCSI device sdj: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.145640] SCSI device sdj: drive cache: write through
> > 	[   69.145780]  sdj:<6>IP: routing cache hash table of 
> > 8192 buckets, 64Kbytes
> > 	[   69.150433] TCP established hash table entries: 
> > 131072 (order: 8, 1048576 bytes)
> > 	[   69.151333] TCP bind hash table entries: 65536 
> > (order: 7, 524288 bytes)
> > 	[   69.151870] TCP: Hash tables configured (established 
> > 131072 bind 65536)
> >         [   69.152110] NET: Registered protocol family 1
> >         [   69.153802]  unknown partition table
> > 	[   69.153959] Attached scsi disk sdj at scsi3, channel 
> > 0, id 0, lun 9
> > 	[   69.154482]   Vendor: DotHill   Model: SANnet II FC  
> >    Rev: 327R
> > 	[   69.154867]   Type:   Direct-Access                  
> >    ANSI SCSI revision: 03
> > 	[   69.155484] SCSI device sdk: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.156083] SCSI device sdk: drive cache: write through
> > 	[   69.156502] SCSI device sdk: 2097152 512-byte hdwr 
> > sectors (1074 MB)
> >         [   69.157095] SCSI device sdk: drive cache: write through
> >         [   69.157234]  sdk: unknown partition table
> > 	[   69.168099] Attached scsi disk sdk at scsi3, channel 
> > 0, id 0, lun 10
> >         
> >         
> >         
> >         
> >         
> > 	On 10/5/05, Ian Pratt <m+Ian.Pratt@xxxxxxxxxxxx> wrote: 
> >
> >                 Has anyone used xen succefully with a qla2300?
> >                 
> >                 What machines have this card?
> >                 
> >                 Ian
> >                 
> > 		> I've installed Xen 3.0-devel on SUSE Linux 
> > without any problems.
> > 		> But when i tryed to boot the system, i've got 
> > a funny problem: 
> > 		>
> > 		> qla2300 0000:05:01.0: Found an ISP2312, irq 
> > 185, iobase
> > 		> 0xf8812000 qla2300 0000:05:01.0: Configuring 
> > PCI space...
> >                 > qla2300 0000:05:01.0: Configure NVRAM parameters...
> >                 > qla2300 0000:05: 01.0: Verifying loaded RISC code...
> >                 > qla2300 0000:05:01.0: Waiting for LIP to complete...
> >                 >
> >                 > until here all works fine, but then:
> >                 >
> > 		> input: PS/2 Generic Mouse on 
> > synaptcs-pt/serio0 qla2300 
> > 		> 0000:05:01.0: LIP reset occured (f7f7).
> >                 > qla2300 0000:05:01.0: LOOP UP detected (2 Gbps).
> > 		> qla2300 0000:05:01.0: Topology - (F_Port), 
> > Host Loop address 0xffff
> >                 > scsi3 : qla2xxx
> >                 > qla2300 0000:04: 02.0:
> >                 >   QLogic Fibre Channel HBA Driver: 8.01.00b5-k
> > 		>   QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, 
> > Single Channel
> > 		>   ISP2312: PCI-X (100 MHz) @ 0000:05:01.0 
> > hdma+, host#=3,
> >                 > fw=3.03.15 IPX
> > 		> Loading kernel/fs/reiserfs/reiserfs.ko 
> > 		> Waiting for device /dev/sda4 to appear: 
> > .....not found ---
> >                 > exiting to /bin/sh $
> >                 >
> > 		> if i use the standard (bigsmp) kernel the 
> > normal massages are:
> >                 >
> > 		> SCSI device sda: 41943040 512-byte hdwr 
> > sectors (21475 MB) 
> > 		> SCSI device sda: drive cache: write back SCSI 
> > device sda:
> > 		> 41943040 512-byte hdwr sectors (21475 MB) 
> > SCSI device sda:
> >                 > drive cache: write back
> >                 >  sda: sda1 sda2 sda3 sda4
> >                 > ....usw.
> > 		> 
> > 		> Well, my qla2300 has the storage attached not 
> > a generic mouse.
> > 		> Of course it isn't possible to boot from this 
> > mouse. :-(
> >                 
> >                 
> >                 
> >                 _______________________________________________
> > 		Xen-users mailing list 
> > 		Xen-users@xxxxxxxxxxxxxxxxxxx
> >                 http://lists.xensource.com/xen-users
> >                 
> >
> >
> >
> >    
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-devel
>
>  

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel