As reported earlier, booting xenLinux 2.4.36 with a 3ware ATA-RAID Controller
(7500-4)
does not work and runs into timeouts during the boot process and then goes into
an inifinite loop while trying to initialize the 3ware card.
I have now added an additonal normal ATA-Harddisk directly to the system.
Then I configured the 3w-xxxx driver as a module and booted from the single
ATA-Harddisk.
This gives me the chance to activate SCSI-Logging (That's a Kernel-Option and
is activated
via echo "scsi log all" > /proc/scsi/scsi") which logs a lot of SCSI tracing to
the kernel log.
After booting I just activated the SCSi logging and then did "modprobe
3w-xxxx". This tries
to load the 3ware module and to initialize the 3ware driver -- with the same
failiure again btw. ;-)
However, now there's a lot of SCSI debugging available, perhaps the Xen team or
somebody
else has some ideas what the problem might be by looking at the log ? TIA.
I know too little about the linux SCSI system to make much out of it.
Also as reported earlier, I could not get any additional output from Xen on the
serial
console while the system tried to initialize the 3ware controller.
I build Xen (being in the "xen" directory) with "make clean", "debug=y make",
"debug=y install". Are there any additional options to get more tracing from
Xen or
even from XenLinux 2.4 ?
This might be very helpfull in order to trace what's happening during the
timeouts.
Log is attached to this message.
Sven
Aug 13 16:05:30 filer11 kernel: scsi logging level set to 0xffffffff
Aug 13 16:05:40 filer11 kernel: 3ware Storage Controller device driver for
Linux v1.02.00.037.
Aug 13 16:05:40 filer11 kernel: PCI: Obtained IRQ 72 for device 03:03.0
Aug 13 16:05:40 filer11 kernel: scsi1 : Found a 3ware Storage Controller at
0xc800, IRQ: 72, P-chip: 1.3
Aug 13 16:05:40 filer11 kernel: Wake up parent -1
Aug 13 16:05:40 filer11 kernel: Error handler sleeping
Aug 13 16:05:40 filer11 kernel: scsi1 : 3ware Storage Controller
Aug 13 16:05:40 filer11 kernel: scsi: performing INQUIRY
Aug 13 16:05:40 filer11 kernel: scsi_do_req (host = 1, channel = 0 target = 0,
buffer =c608fdc0, bufflen = 256, done = c023a1a0, timeout = 600, retries = 3)
Aug 13 16:05:40 filer11 kernel: command : 12 00 00 00 ff 00
Aug 13 16:05:40 filer11 kernel: Activating command for device 0 (1)
Aug 13 16:05:40 filer11 kernel: Leaving scsi_init_cmd_from_req()
Aug 13 16:05:40 filer11 kernel: Adding timer for command c1536e00 at 600
(c023f5e0)
Aug 13 16:05:40 filer11 kernel: scsi_dispatch_cmnd (host = 1, channel = 0,
target = 0, command = c1536e58, buffer = c608fdc0,
Aug 13 16:05:40 filer11 kernel: bufflen = 256, done = c023a1a0)
Aug 13 16:05:40 filer11 kernel: queuecommand : routine at c84e1cb0
Aug 13 16:05:40 filer11 kernel: leaving scsi_dispatch_cmnd()
Aug 13 16:05:40 filer11 kernel: Leaving scsi_do_req()
Aug 13 16:05:46 filer11 kernel: Command timed out active=1 busy=1 failed=1
Aug 13 16:05:49 filer11 kernel: Error handler waking up
Aug 13 16:05:49 filer11 kernel: scsi_unjam_host: Checking to see if we need to
request sense
Aug 13 16:05:49 filer11 kernel: Command to ID 0 timedout
Aug 13 16:05:49 filer11 kernel: Total of 0+1 commands on 1 devices require eh
work
Aug 13 16:05:49 filer11 kernel: scsi_unjam_host: Checking to see if we want to
try abort
Aug 13 16:05:49 filer11 kernel: 3w-xxxx: scsi1: Unit #0: Command (c1536e00)
timed out, resetting card.
Aug 13 16:05:49 filer11 kernel: Clearing timer for command c1536e00 0
Aug 13 16:05:49 filer11 kernel: Adding timer for command c1536e00 at 1000
(c023f7b0)
Aug 13 16:05:59 filer11 kernel: In scsi_eh_times_out c1536e00
Aug 13 16:06:04 filer11 kernel: 3w-xxxx: scsi1: Unit #0: Command (c1536e00)
timed out, resetting card.
Aug 13 16:06:04 filer11 kernel: send_eh_cmnd: c1536e00 eh_state:2003
Aug 13 16:06:04 filer11 kernel: scsi_test_unit_ready: SCpnt c1536e00 eh_state
2003
Aug 13 16:06:04 filer11 kernel: scsi_unjam_host: Checking to see if we want to
try BDR
Aug 13 16:06:04 filer11 kernel: scsi_unjam_host: Try hard bus reset
Aug 13 16:06:04 filer11 kernel: scsi_unjam_host: Try hard host reset
Aug 13 16:06:04 filer11 kernel: 3w-xxxx: scsi1: Reset succeeded.
Aug 13 16:06:04 filer11 kernel: Sleeping for timer tics 1000
Aug 13 16:06:14 filer11 kernel: Adding timer for command c1536e00 at 1000
(c023f7b0)
Aug 13 16:06:24 filer11 kernel: In scsi_eh_times_out c1536e00
Aug 13 16:06:26 filer11 kernel: 3w-xxxx: scsi1: Unit #0: Command (c1536e00)
timed out, resetting card.
Aug 13 16:06:26 filer11 kernel: send_eh_cmnd: c1536e00 eh_state:2003
Aug 13 16:06:26 filer11 kernel: scsi_test_unit_ready: SCpnt c1536e00 eh_state
2003
Aug 13 16:06:26 filer11 kernel: scsi: device set offline - not ready or command
retry failed after host reset: host 1 channel 0 id 0 lun 0
Aug 13 16:06:26 filer11 kernel: Adding timer for command c1536e00 at 100
(c023f7b0)
Aug 13 16:06:26 filer11 kernel: Clearing timer for command c1536e00 1
Aug 13 16:06:26 filer11 kernel: scsi_error.c: Waking up host to restart
Aug 13 16:06:26 filer11 kernel: Error handler sleeping
Aug 13 16:06:26 filer11 kernel: scsi_error.c: device offline - report as SUCCESS
Aug 13 16:06:26 filer11 kernel: Command finished 1 0 0x80000
Aug 13 16:06:26 filer11 kernel: Notifying upper driver of completion for device
0 80000
Aug 13 16:06:26 filer11 kernel: Deactivating command for device 0 (active=0,
failed=0)
Aug 13 16:06:26 filer11 kernel: scsi: INQUIRY failed with code 0x80000
Aug 13 16:06:26 filer11 kernel: scsi: performing INQUIRY
Aug 13 16:06:26 filer11 kernel: scsi_do_req (host = 1, channel = 0 target = 1,
buffer =c608fdc0, bufflen = 256, done = c023a1a0, timeout = 600, retries = 3)
Aug 13 16:06:26 filer11 kernel: command : 12 00 00 00 ff 00
Aug 13 16:06:26 filer11 kernel: Activating command for device 1 (1)
Aug 13 16:06:26 filer11 kernel: Leaving scsi_init_cmd_from_req()
Aug 13 16:06:26 filer11 kernel: Adding timer for command c5f80800 at 600
(c023f5e0)
Aug 13 16:06:26 filer11 kernel: scsi_dispatch_cmnd (host = 1, channel = 0,
target = 1, command = c5f80858, buffer = c608fdc0,
Aug 13 16:06:26 filer11 kernel: bufflen = 256, done = c023a1a0)
Aug 13 16:06:26 filer11 kernel: queuecommand : routine at c84e1cb0
Aug 13 16:06:26 filer11 kernel: leaving scsi_dispatch_cmnd()
Aug 13 16:06:26 filer11 kernel: Leaving scsi_do_req()
Aug 13 16:06:32 filer11 kernel: Command timed out active=1 busy=1 failed=1
Aug 13 16:06:35 filer11 kernel: Error handler waking up
Aug 13 16:06:35 filer11 kernel: scsi_unjam_host: Checking to see if we need to
request sense
Aug 13 16:06:35 filer11 kernel: Command to ID 1 timedout
Aug 13 16:06:35 filer11 kernel: Total of 0+1 commands on 1 devices require eh
work
Aug 13 16:06:35 filer11 kernel: scsi_unjam_host: Checking to see if we want to
try abort
Aug 13 16:06:35 filer11 kernel: 3w-xxxx: scsi1: Unit #1: Command (c5f80800)
timed out, resetting card.
Aug 13 16:06:35 filer11 kernel: Clearing timer for command c5f80800 0
Aug 13 16:06:35 filer11 kernel: Adding timer for command c5f80800 at 1000
(c023f7b0)
Aug 13 16:06:45 filer11 kernel: In scsi_eh_times_out c5f80800
Aug 13 16:06:50 filer11 kernel: 3w-xxxx: scsi1: Unit #1: Command (c5f80800)
timed out, resetting card.
Aug 13 16:06:50 filer11 kernel: send_eh_cmnd: c5f80800 eh_state:2003
Aug 13 16:06:50 filer11 kernel: scsi_test_unit_ready: SCpnt c5f80800 eh_state
2003
Aug 13 16:06:50 filer11 kernel: scsi_unjam_host: Checking to see if we want to
try BDR
Aug 13 16:06:50 filer11 kernel: scsi_unjam_host: Try hard bus reset
Aug 13 16:06:50 filer11 kernel: scsi_unjam_host: Try hard host reset
Aug 13 16:06:50 filer11 kernel: 3w-xxxx: scsi1: Reset succeeded.
Aug 13 16:06:50 filer11 kernel: Sleeping for timer tics 1000
Aug 13 16:07:00 filer11 kernel: Adding timer for command c5f80800 at 1000
(c023f7b0)
Aug 13 16:07:10 filer11 kernel: In scsi_eh_times_out c5f80800
Aug 13 16:07:13 filer11 kernel: 3w-xxxx: scsi1: Unit #1: Command (c5f80800)
timed out, resetting card.
Aug 13 16:07:13 filer11 kernel: send_eh_cmnd: c5f80800 eh_state:2003
Aug 13 16:07:13 filer11 kernel: scsi_test_unit_ready: SCpnt c5f80800 eh_state
2003
Aug 13 16:07:13 filer11 kernel: scsi: device set offline - not ready or command
retry failed after host reset: host 1 channel 0 id 1 lun 0
Aug 13 16:07:13 filer11 kernel: Adding timer for command c5f80800 at 100
(c023f7b0)
Aug 13 16:07:13 filer11 kernel: Clearing timer for command c5f80800 1
Aug 13 16:07:13 filer11 kernel: scsi_error.c: Waking up host to restart
Aug 13 16:07:13 filer11 kernel: Error handler sleeping
Aug 13 16:07:13 filer11 kernel: scsi_error.c: device offline - report as SUCCESS
Aug 13 16:07:13 filer11 kernel: Command finished 1 0 0x80000
Aug 13 16:07:13 filer11 kernel: Notifying upper driver of completion for device
1 80000
Aug 13 16:07:13 filer11 kernel: Deactivating command for device 1 (active=0,
failed=0)
Aug 13 16:07:13 filer11 kernel: scsi: INQUIRY failed with code 0x80000
Aug 13 16:07:13 filer11 kernel: scsi: performing INQUIRY
Aug 13 16:07:13 filer11 kernel: scsi_do_req (host = 1, channel = 0 target = 2,
buffer =c608fdc0, bufflen = 256, done = c023a1a0, timeout = 600, retries = 3)
Aug 13 16:07:13 filer11 kernel: command : 12 00 00 00 ff 00
Aug 13 16:07:13 filer11 kernel: Activating command for device 2 (1)
Aug 13 16:07:13 filer11 kernel: Leaving scsi_init_cmd_from_req()
Aug 13 16:07:13 filer11 kernel: Adding timer for command c5f80800 at 600
(c023f5e0)
Aug 13 16:07:13 filer11 kernel: scsi_dispatch_cmnd (host = 1, channel = 0,
target = 2, command = c5f80858, buffer = c608fdc0,
Aug 13 16:07:13 filer11 kernel: bufflen = 256, done = c023a1a0)
Aug 13 16:07:13 filer11 kernel: queuecommand : routine at c84e1cb0
Aug 13 16:07:13 filer11 kernel: leaving scsi_dispatch_cmnd()
Aug 13 16:07:13 filer11 kernel: Leaving scsi_do_req()
Aug 13 16:07:19 filer11 kernel: Command timed out active=1 busy=1 failed=1
Aug 13 16:07:22 filer11 kernel: Error handler waking up
Aug 13 16:07:22 filer11 kernel: scsi_unjam_host: Checking to see if we need to
request sense
Aug 13 16:07:22 filer11 kernel: Command to ID 2 timedout
Aug 13 16:07:22 filer11 kernel: Total of 0+1 commands on 1 devices require eh
work
Aug 13 16:07:22 filer11 kernel: scsi_unjam_host: Checking to see if we want to
try abort
Aug 13 16:07:22 filer11 kernel: 3w-xxxx: scsi1: Unit #2: Command (c5f80800)
timed out, resetting card.
Aug 13 16:07:22 filer11 kernel: Clearing timer for command c5f80800 0
Aug 13 16:07:22 filer11 kernel: Adding timer for command c5f80800 at 1000
(c023f7b0)
Aug 13 16:07:32 filer11 kernel: In scsi_eh_times_out c5f80800
Aug 13 16:07:37 filer11 kernel: 3w-xxxx: scsi1: Unit #2: Command (c5f80800)
timed out, resetting card.
Aug 13 16:07:37 filer11 kernel: send_eh_cmnd: c5f80800 eh_state:2003
Aug 13 16:07:37 filer11 kernel: scsi_test_unit_ready: SCpnt c5f80800 eh_state
2003
Aug 13 16:07:37 filer11 kernel: scsi_unjam_host: Checking to see if we want to
try BDR
Aug 13 16:07:37 filer11 kernel: scsi_unjam_host: Try hard bus reset
Aug 13 16:07:37 filer11 kernel: scsi_unjam_host: Try hard host reset
Aug 13 16:07:37 filer11 kernel: 3w-xxxx: scsi1: Reset succeeded.
Aug 13 16:07:37 filer11 kernel: Sleeping for timer tics 1000
Aug 13 16:07:47 filer11 kernel: Adding timer for command c5f80800 at 1000
(c023f7b0)
Aug 13 16:07:55 filer11 shutdown: shutting down for system reboot
...
-------------------------------------------------------
SF.Net email is sponsored by Shop4tech.com-Lowest price on Blank Media
100pk Sonic DVD-R 4x for only $29 -100pk Sonic DVD+R for only $33
Save 50% off Retail on Ink & Toner - Free Shipping and Free Gift.
http://www.shop4tech.com/z/Inkjet_Cartridges/9_108_r285
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.sourceforge.net/lists/listinfo/xen-devel
|
Home