# HG changeset patch
# User kaf24@xxxxxxxxxxxxxxxxxxxx
# Node ID 2b0078f771cc1152a003721e20c3972fe7cf6ea8
# Parent 18fa851b6dc6ca5893709b480cf38ee7c5ef445e
Upgrade mpparse.c to linux-2.6.16-rc2 codebase.
Signed-off-by: Keir Fraser <keir@xxxxxxxxxxxxx>
diff -r 18fa851b6dc6 -r 2b0078f771cc xen/arch/x86/mpparse.c
--- a/xen/arch/x86/mpparse.c Thu Feb 16 16:19:38 2006
+++ b/xen/arch/x86/mpparse.c Thu Feb 16 16:37:21 2006
@@ -37,6 +37,12 @@
int smp_found_config;
unsigned int __initdata maxcpus = NR_CPUS;
+#ifdef CONFIG_HOTPLUG_CPU
+#define CPU_HOTPLUG_ENABLED (1)
+#else
+#define CPU_HOTPLUG_ENABLED (0)
+#endif
+
/*
* Various Linux-internal data structures created from the
* MP-table.
@@ -47,7 +53,7 @@
int mp_bus_id_to_local [MAX_MP_BUSSES];
int quad_local_to_mp_bus_id [NR_CPUS/4][4];
int mp_bus_id_to_pci_bus [MAX_MP_BUSSES] = { [0 ... MAX_MP_BUSSES-1] = -1 };
-int mp_current_pci_id;
+static int mp_current_pci_id;
/* I/O APIC entries */
struct mpc_config_ioapic mp_ioapics[MAX_IO_APICS];
@@ -63,7 +69,7 @@
int pic_mode;
unsigned long mp_lapic_addr;
-unsigned int def_to_bigsmp;
+unsigned int def_to_bigsmp = 0;
/* Processor that is doing the boot up */
unsigned int boot_cpu_physical_apicid = -1U;
@@ -119,10 +125,10 @@
}
#endif
-void __init MP_processor_info (struct mpc_config_processor *m)
+static void __devinit MP_processor_info (struct mpc_config_processor *m)
{
int ver, apicid;
- physid_mask_t tmp;
+ physid_mask_t phys_cpu;
if (!(m->mpc_cpuflag & CPU_ENABLED))
return;
@@ -180,48 +186,57 @@
if (m->mpc_cpuflag & CPU_BOOTPROCESSOR) {
Dprintk(" Bootup CPU\n");
boot_cpu_physical_apicid = m->mpc_apicid;
- boot_cpu_logical_apicid = apicid;
- }
-
- if (num_processors >= NR_CPUS) {
- printk(KERN_WARNING "WARNING: NR_CPUS limit of %i reached."
- " Processor ignored.\n", NR_CPUS);
- return;
- }
-
- if (num_processors >= maxcpus) {
- printk(KERN_WARNING "WARNING: maxcpus limit of %i reached."
- " Processor ignored.\n", maxcpus);
- return;
- }
- num_processors++;
+ }
+
ver = m->mpc_apicver;
if (!MP_valid_apicid(apicid, ver)) {
printk(KERN_WARNING "Processor #%d INVALID. (Max ID: %d).\n",
m->mpc_apicid, MAX_APICS);
- --num_processors;
- return;
- }
-
- tmp = apicid_to_cpu_present(apicid);
- physids_or(phys_cpu_present_map, phys_cpu_present_map, tmp);
-
+ return;
+ }
+
/*
* Validate version
*/
if (ver == 0x0) {
- printk(KERN_WARNING "BIOS bug, APIC version is 0 for CPU#%d!
fixing up to 0x10. (tell your hw vendor)\n", m->mpc_apicid);
+ printk(KERN_WARNING "BIOS bug, APIC version is 0 for CPU#%d! "
+ "fixing up to 0x10. (tell your hw vendor)\n",
+ m->mpc_apicid);
ver = 0x10;
}
apic_version[m->mpc_apicid] = ver;
- if ((num_processors > 8) &&
- APIC_XAPIC(ver) &&
- (boot_cpu_data.x86_vendor == X86_VENDOR_INTEL))
- def_to_bigsmp = 1;
- else
- def_to_bigsmp = 0;
-
+
+ phys_cpu = apicid_to_cpu_present(apicid);
+ physids_or(phys_cpu_present_map, phys_cpu_present_map, phys_cpu);
+
+ if (num_processors >= NR_CPUS) {
+ printk(KERN_WARNING "WARNING: NR_CPUS limit of %i reached."
+ " Processor ignored.\n", NR_CPUS);
+ return;
+ }
+
+ if (num_processors >= maxcpus) {
+ printk(KERN_WARNING "WARNING: maxcpus limit of %i reached."
+ " Processor ignored.\n", maxcpus);
+ return;
+ }
+
+ cpu_set(num_processors, cpu_possible_map);
+ num_processors++;
+
+ if (CPU_HOTPLUG_ENABLED || (num_processors > 8)) {
+ switch (boot_cpu_data.x86_vendor) {
+ case X86_VENDOR_INTEL:
+ if (!APIC_XAPIC(ver)) {
+ def_to_bigsmp = 0;
+ break;
+ }
+ /* If P4 and above fall through */
+ case X86_VENDOR_AMD:
+ def_to_bigsmp = 1;
+ }
+ }
bios_cpu_apicid[num_processors - 1] = m->mpc_apicid;
}
@@ -662,8 +677,6 @@
struct intel_mp_floating *mpf = mpf_found;
/*
- * ACPI may be used to obtain the entire SMP configuration or just to
- * enumerate/configure processors (CONFIG_ACPI_BOOT). Note that
* ACPI supports both logical (e.g. Hyper-Threading) and physical
* processors, where MPS only supports physical.
*/
@@ -820,7 +833,7 @@
ACPI-based MP Configuration
--------------------------------------------------------------------------
*/
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
void __init mp_register_lapic_address (
u64 address)
@@ -836,7 +849,7 @@
}
-void __init mp_register_lapic (
+void __devinit mp_register_lapic (
u8 id,
u8 enabled)
{
@@ -866,12 +879,12 @@
MP_processor_info(&processor);
}
-#if defined(CONFIG_X86_IO_APIC) && (defined(CONFIG_ACPI_INTERPRETER) ||
defined(CONFIG_ACPI_BOOT))
+#ifdef CONFIG_X86_IO_APIC
#define MP_ISA_BUS 0
#define MP_MAX_IOAPIC_PIN 127
-struct mp_ioapic_routing {
+static struct mp_ioapic_routing {
int apic_id;
int gsi_base;
int gsi_end;
@@ -1067,7 +1080,7 @@
#define MAX_GSI_NUM 4096
-int mp_register_gsi (u32 gsi, int edge_level, int active_high_low)
+int mp_register_gsi (u32 gsi, int triggering, int polarity)
{
int ioapic = -1;
int ioapic_pin = 0;
@@ -1078,7 +1091,7 @@
* represent all possible interrupts, and IRQs
* assigned to actual devices.
*/
- static int gsi_to_irq[MAX_GSI_NUM];
+ static int gsi_to_irq[MAX_GSI_NUM];
#ifdef CONFIG_ACPI_BUS
/* Don't set up the ACPI SCI because it's already set up */
@@ -1118,14 +1131,22 @@
mp_ioapic_routing[ioapic].pin_programmed[idx] |= (1<<bit);
- if (edge_level) {
+ if (triggering == ACPI_LEVEL_SENSITIVE) {
/*
* For PCI devices assign IRQs in order, avoiding gaps
* due to unused I/O APIC pins.
*/
int irq = gsi;
if (gsi < MAX_GSI_NUM) {
- gsi = pci_irq++;
+ if (gsi > 15)
+ gsi = pci_irq++;
+#ifdef CONFIG_ACPI_BUS
+ /*
+ * Don't assign IRQ used by ACPI SCI
+ */
+ if (gsi == acpi_fadt.sci_int)
+ gsi = pci_irq++;
+#endif
gsi_to_irq[irq] = gsi;
} else {
printk(KERN_ERR "GSI %u is too high\n", gsi);
@@ -1134,10 +1155,10 @@
}
io_apic_set_pci_routing(ioapic, ioapic_pin, gsi,
- edge_level == ACPI_EDGE_SENSITIVE ? 0 : 1,
- active_high_low == ACPI_ACTIVE_HIGH ? 0 : 1);
+ triggering == ACPI_EDGE_SENSITIVE ? 0 : 1,
+ polarity == ACPI_ACTIVE_HIGH ? 0 : 1);
return gsi;
}
-#endif /*CONFIG_X86_IO_APIC && (CONFIG_ACPI_INTERPRETER || CONFIG_ACPI_BOOT)*/
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /* CONFIG_X86_IO_APIC */
+#endif /* CONFIG_ACPI */
_______________________________________________
Xen-changelog mailing list
Xen-changelog@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-changelog
|
Home